[PATCH v2 2/2] arm64: dts: renesas: rzg3s-smarc: Enable SDHI1

[Claudiu]

From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>

Add SDHI1 to RZ/G3S Smarc Carrier-II board. This is connected to a uSD
interface. Although Vccq doesn't cross the boundary of SoM it has
been added to RZ/G3S Smarc Carrier-II dtsi to have all the bits related to
SDHI1 in a single place. At the moment SoM is used only with RZ/G3S Smarc
Carrier-II board.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
---

Changes in v2:
- change regulators' names to regulator-vcc-sdhi1 and
  regulator-vccq-sdhi1
  
 arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi | 65 ++++++++++++++++++++
 1 file changed, 65 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
index e7073a09ed2e..214520137230 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
@@ -11,6 +11,26 @@
 / {
 	aliases {
 		serial0 = &scif0;
+		mmc1 = &sdhi1;
+	};
+
+	vcc_sdhi1: regulator-vcc-sdhi1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&pinctrl RZG2L_GPIO(2, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&pinctrl RZG2L_GPIO(4, 2) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
 	};
 };
 
@@ -19,6 +39,38 @@ scif0_pins: scif0 {
 		pinmux = <RZG2L_PORT_PINMUX(6, 3, 1)>, /* RXD */
 			 <RZG2L_PORT_PINMUX(6, 4, 1)>; /* TXD */
 	};
+
+	sdhi1_pins: sd1 {
+		data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <3300>;
+		};
+
+		ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <3300>;
+		};
+
+		cd {
+			pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+		};
+	};
+
+	sdhi1_pins_uhs: sd1-uhs {
+		data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <1800>;
+		};
+
+		ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <1800>;
+		};
+
+		cd {
+			pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+		};
+	};
 };
 
 &scif0 {
@@ -26,3 +78,16 @@ &scif0 {
 	pinctrl-0 = <&scif0_pins>;
 	status = "okay";
 };
+
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+	vmmc-supply = <&vcc_sdhi1>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <125000000>;
+	status = "okay";
+};
-- 
2.39.2