[PATCH v8 23/25] timer: Implement the hierarchical pull model

[Anna-Maria Behnsen]

Placing timers at enqueue time on a target CPU based on dubious heuristics
does not make any sense:

 1) Most timer wheel timers are canceled or rearmed before they expire.

 2) The heuristics to predict which CPU will be busy when the timer expires
    are wrong by definition.

So placing the timers at enqueue wastes precious cycles.

The proper solution to this problem is to always queue the timers on the
local CPU and allow the non pinned timers to be pulled onto a busy CPU at
expiry time.

Therefore split the timer storage into local pinned and global timers:
Local pinned timers are always expired on the CPU on which they have been
queued. Global timers can be expired on any CPU.

As long as a CPU is busy it expires both local and global timers. When a
CPU goes idle it arms for the first expiring local timer. If the first
expiring pinned (local) timer is before the first expiring movable timer,
then no action is required because the CPU will wake up before the first
movable timer expires. If the first expiring movable timer is before the
first expiring pinned (local) timer, then this timer is queued into a idle
timerqueue and eventually expired by some other active CPU.

To avoid global locking the timerqueues are implemented as a hierarchy. The
lowest level of the hierarchy holds the CPUs. The CPUs are associated to
groups of 8, which are separated per node. If more than one CPU group
exist, then a second level in the hierarchy collects the groups. Depending
on the size of the system more than 2 levels are required. Each group has a
"migrator" which checks the timerqueue during the tick for remote expirable
timers.

If the last CPU in a group goes idle it reports the first expiring event in
the group up to the next group(s) in the hierarchy. If the last CPU goes
idle it arms its timer for the first system wide expiring timer to ensure
that no timer event is missed.

Signed-off-by: Anna-Maria Behnsen <anna-maria@xxxxxxxxxxxxx>
---
v8:
  - Review of Frederic:
    - Fix hotplug race (introduction of wakeup_recalc)
    - Make wakeup and wakeup_recalc logic consistent all over the place
    - Fix child/group state race and read it with locks held
  - Add more clarifying comments
  - Fix grammar all over the place
  - change integers which act as boolean value into bool
  - rewrite condition in tmigr_check_migrator() without negation
  - Improve update events logic with a check of the first event
  - Implement a quick forecast which is called when
    get_next_timer_interrupt() is executed.

v7:
  - Review remarks of Frederic and bigeasy:
    - change logic in tmigr_handle_remote_cpu()
    - s/kzalloc/kcalloc
    - move timer_expire_remote() into NO_HZ_COMMON && SMP config section
    - drop DBG_BUG_ON() makro and use only WARN_ON_ONCE()
    - remove leftovers from sibling logic during setup
  - Move timer_expire_remote() into tick-internal.h
  - Add documentation section about "Required event and timerqueue update
    after remote expiry"
  - Fix fallout of kernel test robot

v6:
  - Fix typos
  - Review remarks of Peter Zijlstra (locking, struct member cleanup, use
    atomic_try_cmpxchg(), update struct member descriptions)
  - Fix race in tmigr_handle_remote_cpu() (Frederic Weisbecker)

v5:
  - Review remarks of Frederic
  - Return nextevt when CPU is marked offline in timer migration hierarchy
    instead of KTIME_MAX
  - Fix update of group events issue, after remote expiring

v4:
  - Fold typo fix in comment into proper patch "timer: Split out "get next
    timer interrupt" functionality"
  - Update wrong comment for tmigr_state union definition
  - Fix fallout of kernel test robot
---
 include/linux/cpuhotplug.h    |    1 +
 kernel/time/Makefile          |    3 +
 kernel/time/tick-internal.h   |    1 +
 kernel/time/timer.c           |   81 +-
 kernel/time/timer_migration.c | 1612 +++++++++++++++++++++++++++++++++
 kernel/time/timer_migration.h |  144 +++
 6 files changed, 1836 insertions(+), 6 deletions(-)
 create mode 100644 kernel/time/timer_migration.c
 create mode 100644 kernel/time/timer_migration.h

diff --git a/include/linux/cpuhotplug.h b/include/linux/cpuhotplug.h
index 06dda85f0424..ed992268f206 100644
--- a/include/linux/cpuhotplug.h
+++ b/include/linux/cpuhotplug.h
@@ -244,6 +244,7 @@ enum cpuhp_state {
 	CPUHP_AP_PERF_POWERPC_HV_24x7_ONLINE,
 	CPUHP_AP_PERF_POWERPC_HV_GPCI_ONLINE,
 	CPUHP_AP_PERF_CSKY_ONLINE,
+	CPUHP_AP_TMIGR_ONLINE,
 	CPUHP_AP_WATCHDOG_ONLINE,
 	CPUHP_AP_WORKQUEUE_ONLINE,
 	CPUHP_AP_RANDOM_ONLINE,
diff --git a/kernel/time/Makefile b/kernel/time/Makefile
index 7e875e63ff3b..4af2a264a160 100644
--- a/kernel/time/Makefile
+++ b/kernel/time/Makefile
@@ -17,6 +17,9 @@ endif
 obj-$(CONFIG_GENERIC_SCHED_CLOCK)		+= sched_clock.o
 obj-$(CONFIG_TICK_ONESHOT)			+= tick-oneshot.o tick-sched.o
 obj-$(CONFIG_LEGACY_TIMER_TICK)			+= tick-legacy.o
+ifeq ($(CONFIG_SMP),y)
+ obj-$(CONFIG_NO_HZ_COMMON)			+= timer_migration.o
+endif
 obj-$(CONFIG_HAVE_GENERIC_VDSO)			+= vsyscall.o
 obj-$(CONFIG_DEBUG_FS)				+= timekeeping_debug.o
 obj-$(CONFIG_TEST_UDELAY)			+= test_udelay.o
diff --git a/kernel/time/tick-internal.h b/kernel/time/tick-internal.h
index 7dbf5ab43d06..fb1568259c21 100644
--- a/kernel/time/tick-internal.h
+++ b/kernel/time/tick-internal.h
@@ -166,6 +166,7 @@ extern void fetch_next_timer_interrupt_remote(unsigned long basej, u64 basem,
 					      unsigned int cpu);
 extern void timer_lock_remote_bases(unsigned int cpu);
 extern void timer_unlock_remote_bases(unsigned int cpu);
+extern void timer_expire_remote(unsigned int cpu);
 # endif
 #else /* CONFIG_NO_HZ_COMMON */
 static inline void timers_update_nohz(void) { }
diff --git a/kernel/time/timer.c b/kernel/time/timer.c
index 7f06553e44de..331c59c0789a 100644
--- a/kernel/time/timer.c
+++ b/kernel/time/timer.c
@@ -53,6 +53,7 @@
 #include <asm/io.h>
 
 #include "tick-internal.h"
+#include "timer_migration.h"
 
 #define CREATE_TRACE_POINTS
 #include <trace/events/timer.h>
@@ -2080,6 +2081,21 @@ void timer_lock_remote_bases(unsigned int cpu)
 	raw_spin_lock(&base_local->lock);
 	raw_spin_lock_nested(&base_global->lock, SINGLE_DEPTH_NESTING);
 }
+
+static void __run_timer_base(struct timer_base *base);
+
+/**
+ * timer_expire_remote - expire global timers of cpu
+ * @cpu:	Remote CPU
+ *
+ * Expire timers of global base of remote CPU.
+ */
+void timer_expire_remote(unsigned int cpu)
+{
+	struct timer_base *base = per_cpu_ptr(&timer_bases[BASE_GLOBAL], cpu);
+
+	__run_timer_base(base);
+}
 # endif /* CONFIG_SMP */
 
 static inline unsigned long __get_next_timer_interrupt(unsigned long basej, u64 basem,
@@ -2113,13 +2129,18 @@ static inline unsigned long __get_next_timer_interrupt(unsigned long basej, u64
  * @basej:	base time jiffies
  * @basem:	base time clock monotonic
  *
- * Returns the tick aligned clock monotonic time of the next pending
- * timer or KTIME_MAX if no timer is pending.
+ * Returns the tick aligned clock monotonic time of the next pending timer
+ * or KTIME_MAX if no timer is pending. If timer of global base was queued
+ * into timer migration hierarchy, first global timer is not taken into
+ * account. If it was the last CPU of timer migration hierarchy going idle,
+ * first global event is taken into account.
  */
 u64 get_next_timer_interrupt(unsigned long basej, u64 basem)
 {
 	struct timer_events tevt = { .local = KTIME_MAX, .global = KTIME_MAX };
 	struct timer_base *base_local, *base_global;
+	u64 tmigr_expires = KTIME_MAX;
+	unsigned long nextevt;
 
 	/*
 	 * Pretend that there is no timer pending if the cpu is offline.
@@ -2134,12 +2155,19 @@ u64 get_next_timer_interrupt(unsigned long basej, u64 basem)
 	raw_spin_lock(&base_local->lock);
 	raw_spin_lock_nested(&base_global->lock, SINGLE_DEPTH_NESTING);
 
-	__get_next_timer_interrupt(basej, basem, base_local, base_global, &tevt);
+	nextevt = __get_next_timer_interrupt(basej, basem, base_local, base_global, &tevt);
+
+	if (time_after(nextevt, basej + 1)) {
+		tmigr_expires = tmigr_quick_check();
+
+		if (tmigr_expires < basem)
+			tmigr_expires = basem;
+	}
 
 	raw_spin_unlock(&base_global->lock);
 	raw_spin_unlock(&base_local->lock);
 
-	tevt.local = min_t(u64, tevt.local, tevt.global);
+	tevt.local = min_t(u64, tevt.local, tmigr_expires);
 
 	return cmp_next_hrtimer_event(basem, tevt.local);
 }
@@ -2194,13 +2222,47 @@ u64 timer_set_idle(unsigned long basej, u64 basem, bool *idle)
 	 */
 	*idle = time_after(nextevt, basej + 1);
 
+	if (*idle) {
+		u64 next_tmigr;
+
+		/*
+		 * Enqueue first global timer into timer migration
+		 * hierarchy, afterwards tevt.global is no longer used.
+		 */
+		next_tmigr = tmigr_cpu_deactivate(tevt.global);
+
+		/*
+		 * If CPU is the last going idle in timer migration
+		 * hierarchy, make sure CPU will wake up in time to handle
+		 * remote timers. next_tmigr == KTIME_MAX if other CPUs are
+		 * still active.
+		 */
+		if (next_tmigr < tevt.local) {
+			u64 tmp;
+
+			/* If we missed a tick already, force 0 delta */
+			if (next_tmigr < basem)
+				next_tmigr = basem;
+
+			tmp = div_u64(next_tmigr - basem, TICK_NSEC);
+
+			nextevt = basej + (unsigned long)tmp;
+			tevt.local = next_tmigr;
+			*idle = time_after(nextevt, basej + 1);
+		}
+		/*
+		 * Update of nextevt is not required in an else path, as it
+		 * is revisited in !is_idle path only.
+		 */
+	}
+
 	/* We need to mark both bases in sync */
 	base_local->is_idle = base_global->is_idle = *idle;
 
 	raw_spin_unlock(&base_global->lock);
 	raw_spin_unlock(&base_local->lock);
 
-	return min_t(u64, tevt.local, tevt.global);
+	return tevt.local;
 }
 
 /**
@@ -2218,6 +2280,9 @@ void timer_clear_idle(void)
 	 */
 	__this_cpu_write(timer_bases[BASE_LOCAL].is_idle, false);
 	__this_cpu_write(timer_bases[BASE_GLOBAL].is_idle, false);
+
+	/* Activate without holding the timer_base->lock */
+	tmigr_cpu_activate();
 }
 #endif
 
@@ -2283,6 +2348,9 @@ static __latent_entropy void run_timer_softirq(struct softirq_action *h)
 	if (IS_ENABLED(CONFIG_NO_HZ_COMMON)) {
 		run_timer_base(BASE_GLOBAL);
 		run_timer_base(BASE_DEF);
+
+		if (is_timers_nohz_active())
+			tmigr_handle_remote();
 	}
 }
 
@@ -2297,7 +2365,8 @@ static void run_local_timers(void)
 
 	for (int i = 0; i < NR_BASES; i++, base++) {
 		/* Raise the softirq only if required. */
-		if (time_after_eq(jiffies, base->next_expiry)) {
+		if (time_after_eq(jiffies, base->next_expiry) ||
+		    (i == BASE_DEF && tmigr_requires_handle_remote())) {
 			raise_softirq(TIMER_SOFTIRQ);
 			return;
 		}
diff --git a/kernel/time/timer_migration.c b/kernel/time/timer_migration.c
new file mode 100644
index 000000000000..929b3b94b893
--- /dev/null
+++ b/kernel/time/timer_migration.c
@@ -0,0 +1,1612 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Infrastructure for migratable timers
+ *
+ * Copyright(C) 2022 linutronix GmbH
+ */
+#include <linux/cpuhotplug.h>
+#include <linux/slab.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/timerqueue.h>
+#include <trace/events/ipi.h>
+
+#include "timer_migration.h"
+#include "tick-internal.h"
+
+/*
+ * The timer migration mechanism is built on a hierarchy of groups. The
+ * lowest level group contains CPUs, the next level groups of CPU groups
+ * and so forth. The CPU groups are kept per node so for the normal case
+ * lock contention won't happen across nodes. Depending on the number of
+ * CPUs per node even the next level might be kept as groups of CPU groups
+ * per node and only the levels above cross the node topology.
+ *
+ * Example topology for a two node system with 24 CPUs each.
+ *
+ * LVL 2			[GRP2:0]
+ *			      GRP1:0 = GRP1:M
+ *
+ * LVL 1            [GRP1:0]		         [GRP1:1]
+ *	         GRP0:0 - GRP0:2	      GRP0:3 - GRP0:5
+ *
+ * LVL 0  [GRP0:0]  [GRP0:1]  [GRP0:2]  [GRP0:3]  [GRP0:4]  [GRP0:5]
+ * CPUS     0-7       8-15     16-23     24-31	   32-39     40-47
+ *
+ * The groups hold a timer queue of events sorted by expiry time. These
+ * queues are updated when CPUs go in idle. When they come out of idle
+ * ignore flag of events is set.
+ *
+ * Each group has a designated migrator CPU/group as long as a CPU/group is
+ * active in the group. This designated role is necessary to avoid that all
+ * active CPUs in a group try to migrate expired timers from other CPUs,
+ * which would result in massive lock bouncing.
+ *
+ * When a CPU is awake, it checks in it's own timer tick the group
+ * hierarchy up to the point where it is assigned the migrator role or if
+ * no CPU is active, it also checks the groups where no migrator is set
+ * (TMIGR_NONE).
+ *
+ * If it finds expired timers in one of the group queues it pulls them over
+ * from the idle CPU and runs the timer function. After that it updates the
+ * group and the parent groups if required.
+ *
+ * CPUs which go idle arm their CPU local timer hardware for the next local
+ * (pinned) timer event. If the next migratable timer expires after the
+ * next local timer or the CPU has no migratable timer pending then the
+ * CPU does not queue an event in the LVL0 group. If the next migratable
+ * timer expires before the next local timer then the CPU queues that timer
+ * in the LVL0 group. In both cases the CPU marks itself idle in the LVL0
+ * group.
+ *
+ * When CPU comes out of idle and when a group has at least a single active
+ * child, the ignore flag of the tmigr_event is set. This indicates, that
+ * the event is ignored even if it is still enqueued in the parent groups
+ * timer queue. It will be removed when touching the timer queue the next
+ * time. This spares locking in active path as the lock protects (after
+ * setup) only event information. For more information about locking,
+ * please read the section "Locking rules".
+ *
+ * If the CPU is the migrator of the group then it delegates that role to
+ * the next active CPU in the group or sets migrator to TMIGR_NONE when
+ * there is no active CPU in the group. This delegation needs to be
+ * propagated up the hierarchy so hand over from other leaves can happen at
+ * all hierarchy levels w/o doing a search.
+ *
+ * When the last CPU in the system goes idle, then it drops all migrator
+ * duties up to the top level of the hierarchy (LVL2 in the example). It
+ * then has to make sure, that it arms it's own local hardware timer for
+ * the earliest event in the system.
+ *
+ *
+ * Lifetime rules:
+ * ---------------
+ *
+ * The groups are built up at init time or when CPUs come online. They are
+ * not destroyed when a group becomes empty due to offlining. The group
+ * just won't participate in the hierarchy management anymore. Destroying
+ * groups would result in interesting race conditions which would just make
+ * the whole mechanism slow and complex.
+ *
+ *
+ * Locking rules:
+ * --------------
+ *
+ * For setting up new groups and handling events it's required to lock both
+ * child and parent group. The lock ordering is always bottom up. This also
+ * includes the per CPU locks in struct tmigr_cpu. For updating the migrator and
+ * active CPU/group information atomic_try_cmpxchg() is used instead and only
+ * the per CPU tmigr_cpu->lock is held.
+ *
+ * During the setup of groups tmigr_level_list is required. It is protected by
+ * @tmigr_mutex.
+ *
+ * When @timer_base->lock as well as tmigr related locks are required, the lock
+ * ordering is: first @timer_base->lock, afterwards tmigr related locks.
+ *
+ *
+ * Protection of the tmigr group state information:
+ * ------------------------------------------------
+ *
+ * The state information with the list of active children and migrator needs to
+ * be protected by a sequence counter. It prevents a race when updates in a
+ * child groups are propagated in changed order. The following scenario
+ * describes what happens without updating the sequence counter:
+ *
+ * Therefore, let's take three groups and four CPUs (CPU2 and CPU3 as well
+ * as GRP0:1 will not change during the scenario):
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:0, GRP0:1
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *           migrator = CPU0           migrator = CPU2
+ *           active   = CPU0           active   = CPU2
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             active      idle           active      idle
+ *
+ *
+ * 1. CPU0 goes idle (changes are updated in GRP0:0; afterwards the current
+ *    states of GRP0:0 and GRP1:0 are stored in the data for walking the
+ *    hierarchy):
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:0, GRP0:1
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *       --> migrator = TMIGR_NONE     migrator = CPU2
+ *       --> active   =                active   = CPU2
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *         --> idle        idle           active      idle
+ *
+ * 2. CPU1 comes out of idle (changes are update in GRP0:0; afterwards the
+ *    current states of GRP0:0 and GRP1:0 are stored in the data for walking the
+ *    hierarchy):
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:0, GRP0:1
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *       --> migrator = CPU1           migrator = CPU2
+ *       --> active   = CPU1           active   = CPU2
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             idle    --> active         active      idle
+ *
+ * 3. Here comes the change of the order: Propagating the changes of step 2
+ *    through the hierarchy to GRP1:0 - nothing to be done, because GRP0:0
+ *    is already up to date.
+ *
+ * 4. Propagating the changes of step 1 through the hierarchy to GRP1:0
+ *
+ *    LVL 1            [GRP1:0]
+ *                 --> migrator = GRP0:1
+ *                 --> active   = GRP0:1
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *           migrator = CPU1           migrator = CPU2
+ *           active   = CPU1           active   = CPU2
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             idle        active         active      idle
+ *
+ * Now there is a inconsistent overall state because GRP0:0 is active, but
+ * it is marked as idle in the GRP1:0. This is prevented by incrementing
+ * sequence counter whenever changing the state.
+ *
+ *
+ * Required event and timerqueue update after a remote expiry:
+ * -----------------------------------------------------------
+ *
+ * After a remote expiry of a CPU, a walk through the hierarchy updating the
+ * events and timerqueues has to be done when there is a 'new' global timer of
+ * the remote CPU (which is obvious) but also if there is no new global timer,
+ * but the remote CPU is still idle:
+ *
+ * 1. CPU2 is the migrator and does the remote expiry in GRP1:0; expiry of
+ *    evt-CPU0 and evt-CPU1 are equal:
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:1
+ *                 --> timerqueue = evt-GRP0:0
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *           migrator = TMIGR_NONE     migrator = CPU2
+ *           active   =                active   = CPU2
+ *           groupevt.ignore = false   groupevt.ignore = true
+ *           groupevt.cpu = CPU0       groupevt.cpu =
+ *           timerqueue = evt-CPU0,    timerqueue =
+ *                        evt-CPU1
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             idle        idle           active      idle
+ *
+ * 2. Remove the first event of the timerqueue in GRP1:0 and expire the timers
+ *    of CPU0 (see evt-GRP0:0->cpu value):
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:1
+ *                 --> timerqueue =
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *           migrator = TMIGR_NONE     migrator = CPU2
+ *           active   =                active   = CPU2
+ *           groupevt.ignore = false   groupevt.ignore = true
+ *       --> groupevt.cpu = CPU0       groupevt.cpu =
+ *           timerqueue = evt-CPU0,    timerqueue =
+ *                        evt-CPU1
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             idle        idle           active      idle
+ *
+ * 3. After the remote expiry CPU0 has no global timer that needs to be
+ *    enqueued. When skipping the walk, the global timer of CPU1 is not handled,
+ *    as the group event of GRP0:0 is not updated and not enqueued into GRP1:0. The
+ *    walk has to be done to update the group events and timerqueues:
+ *
+ *    LVL 1            [GRP1:0]
+ *                     migrator = GRP0:1
+ *                     active   = GRP0:1
+ *                 --> timerqueue = evt-GRP0:0
+ *                   /                \
+ *    LVL 0  [GRP0:0]                  [GRP0:1]
+ *           migrator = TMIGR_NONE     migrator = CPU2
+ *           active   =                active   = CPU2
+ *           groupevt.ignore = false   groupevt.ignore = true
+ *       --> groupevt.cpu = CPU1       groupevt.cpu =
+ *       --> timerqueue = evt-CPU1     timerqueue =
+ *              /         \                /         \
+ *    CPUs     0           1              2           3
+ *             idle        idle           active      idle
+ *
+ * Now CPU2 (migrator) is able to handle the timer of CPU1 as CPU2 only scans
+ * the timerqueues of GRP0:1 and GRP1:0.
+ *
+ * The update of step 3 is valid to be skipped, when the remote CPU went offline
+ * in the meantime because an update was already done during inactive path. When
+ * CPU became active in the meantime, update isn't required as well, because
+ * GRP0:0 is now longer idle.
+ */
+
+static DEFINE_MUTEX(tmigr_mutex);
+static struct list_head *tmigr_level_list __read_mostly;
+
+static unsigned int tmigr_hierarchy_levels __read_mostly;
+static unsigned int tmigr_crossnode_level __read_mostly;
+
+static DEFINE_PER_CPU(struct tmigr_cpu, tmigr_cpu);
+
+#define TMIGR_NONE	0xFF
+#define BIT_CNT		8
+
+static DEFINE_STATIC_KEY_FALSE(tmigr_enabled);
+
+static inline bool is_tmigr_enabled(void)
+{
+	return static_branch_unlikely(&tmigr_enabled);
+}
+
+/*
+ * Returns true, when @childmask corresponds to the group migrator or when the
+ * group is not active - so no migrator is set.
+ */
+static bool tmigr_check_migrator(struct tmigr_group *group, u8 childmask)
+{
+	union tmigr_state s;
+
+	s.state = atomic_read(&group->migr_state);
+
+	if ((s.migrator == childmask) || (s.migrator == TMIGR_NONE))
+		return true;
+
+	return false;
+}
+
+static bool tmigr_check_migrator_and_lonely(struct tmigr_group *group, u8 childmask)
+{
+	bool lonely, migrator = false;
+	unsigned long active;
+	union tmigr_state s;
+
+	s.state = atomic_read(&group->migr_state);
+
+	if ((s.migrator == childmask) || (s.migrator == TMIGR_NONE))
+		migrator = true;
+
+	active = s.active;
+	lonely = bitmap_weight(&active, BIT_CNT) <= 1;
+
+	return (migrator && lonely);
+}
+
+static bool tmigr_check_lonely(struct tmigr_group *group)
+{
+	unsigned long active;
+	union tmigr_state s;
+
+	s.state = atomic_read(&group->migr_state);
+
+	active = s.active;
+
+	return bitmap_weight(&active, BIT_CNT) <= 1;
+}
+
+typedef bool (*up_f)(struct tmigr_group *, struct tmigr_group *, void *);
+
+static void __walk_groups(up_f up, void *data,
+			  struct tmigr_cpu *tmc)
+{
+	struct tmigr_group *child = NULL, *group = tmc->tmgroup;
+
+	do {
+		WARN_ON_ONCE(group->level >= tmigr_hierarchy_levels);
+
+		if (up(group, child, data))
+			break;
+
+		child = group;
+		group = group->parent;
+	} while (group);
+}
+
+static void walk_groups(up_f up, void *data, struct tmigr_cpu *tmc)
+{
+	lockdep_assert_held(&tmc->lock);
+
+	__walk_groups(up, data, tmc);
+}
+
+/**
+ * struct tmigr_walk - data required for walking the hierarchy
+ * @evt:		Pointer to tmigr_event which needs to be queued (of idle
+ *			child group)
+ * @childmask:		childmask of child group
+ * @nextexp:		Next CPU event expiry information which is handed into
+ *			the timer migration code by the timer code
+ *			(get_next_timer_interrupt()); it is furthermore used for
+ *			the first event which is queued, if the timer migration
+ *			hierarchy is completely idle
+ * @childstate:		tmigr_group->migr_state of the child - will be only
+ *			reread when cmpxchg in the group fails (is required for
+ *			the deactivate path and the new timer path)
+ * @groupstate:		tmigr_group->migr_state of the group - will be only
+ *			reread when cmpxchg in the group fails (is required for
+ *			the active, the deactivate and the new timer path)
+ * @remote:		Is set, when the new timer path is executed in
+ *			tmigr_handle_remote_cpu()
+ */
+struct tmigr_walk {
+	struct tmigr_event	*evt;
+	u8			childmask;
+	u64			nextexp;
+	union tmigr_state	childstate;
+	union tmigr_state	groupstate;
+	bool			remote;
+};
+
+/**
+ * struct tmigr_remote_data -	data required for (check) remote expiry
+ *				hierarchy walk
+ * @basej:		timer base in jiffies
+ * @now:		timer base monotonic
+ * @nextexp:		returns expiry of the first timer in the idle timer
+ *			migration hierarchy to make sure the timer is handled in
+ *			time; it is stored in the per CPU tmigr_cpu struct of
+ *			CPU which expires remote timers
+ * @childmask:		childmask of child group
+ * @check:		is set if there is the need to handle remote timers;
+ *			required in tmigr_check_handle_remote() only
+ * @tmc_active:		this flag indicates, whether the CPU which triggers
+ *			the hierarchy walk is !idle in the timer migration
+ *			hierarchy. When the CPU is idle and the whole hierarchy is
+ *			idle, only the first event of the top level has to be
+ *			considered.
+ */
+struct tmigr_remote_data {
+	unsigned long	basej;
+	u64		now;
+	u64		nextexp;
+	u8		childmask;
+	bool		check;
+	bool		tmc_active;
+};
+
+/*
+ * Returns the next event of the timerqueue @group->events
+ *
+ * Removes timers with ignore flag and update next_expiry of the group. Values
+ * of the group event are updated in tmigr_update_events() only.
+ */
+static struct tmigr_event *tmigr_next_groupevt(struct tmigr_group *group)
+{
+	struct timerqueue_node *node = NULL;
+	struct tmigr_event *evt = NULL;
+
+	lockdep_assert_held(&group->lock);
+
+	WRITE_ONCE(group->next_expiry, KTIME_MAX);
+
+	while ((node = timerqueue_getnext(&group->events))) {
+		evt = container_of(node, struct tmigr_event, nextevt);
+
+		if (!evt->ignore) {
+			WRITE_ONCE(group->next_expiry, evt->nextevt.expires);
+			return evt;
+		}
+
+		/*
+		 * Remove next timers with ignore flag, because the group lock
+		 * is held anyway
+		 */
+		if (!timerqueue_del(&group->events, node))
+			break;
+	}
+
+	return NULL;
+}
+
+/*
+ * Return the next event which is already expired of the group timerqueue
+ *
+ * Event, which is returned, is also removed from the queue.
+ */
+static struct tmigr_event *tmigr_next_expired_groupevt(struct tmigr_group *group,
+						     u64 now)
+{
+	struct tmigr_event *evt = tmigr_next_groupevt(group);
+
+	if (!evt || now < evt->nextevt.expires)
+		return NULL;
+
+	/*
+	 * The event is already expired. Remove it. If it's not the last event,
+	 * then update all group event related information.
+	 */
+	if (timerqueue_del(&group->events, &evt->nextevt))
+		tmigr_next_groupevt(group);
+	else
+		WRITE_ONCE(group->next_expiry, KTIME_MAX);
+
+	return evt;
+}
+
+static u64 tmigr_next_groupevt_expires(struct tmigr_group *group)
+{
+	struct tmigr_event *evt;
+
+	evt = tmigr_next_groupevt(group);
+
+	if (!evt)
+		return KTIME_MAX;
+	else
+		return evt->nextevt.expires;
+}
+
+static bool tmigr_active_up(struct tmigr_group *group,
+			    struct tmigr_group *child,
+			    void *ptr)
+{
+	union tmigr_state curstate, newstate;
+	struct tmigr_walk *data = ptr;
+	bool walk_done;
+	u8 childmask;
+
+	childmask = data->childmask;
+	newstate = curstate = data->groupstate;
+
+retry:
+	walk_done = true;
+
+	if (newstate.migrator == TMIGR_NONE) {
+		newstate.migrator = childmask;
+
+		/* Changes need to be propagated */
+		walk_done = false;
+	}
+
+	newstate.active |= childmask;
+
+	newstate.seq++;
+
+	if (!atomic_try_cmpxchg(&group->migr_state, &curstate.state, newstate.state)) {
+		newstate.state = curstate.state;
+		goto retry;
+	}
+
+	if (group->parent && (walk_done == false)) {
+		data->groupstate.state = atomic_read(&group->parent->migr_state);
+		data->childmask = group->childmask;
+	}
+
+	/*
+	 * The group is active and the event will be ignored - the ignore flag is
+	 * updated without holding the lock. In case the bit is set while
+	 * another CPU already handles remote events, nothing happens, because
+	 * it is clear that the CPU became active just in this moment, or in
+	 * worst case the event is handled remote. Nothing to worry about.
+	 */
+	group->groupevt.ignore = true;
+
+	return walk_done;
+}
+
+static void __tmigr_cpu_activate(struct tmigr_cpu *tmc)
+{
+	struct tmigr_walk data;
+
+	data.childmask = tmc->childmask;
+	data.groupstate.state = atomic_read(&tmc->tmgroup->migr_state);
+
+	tmc->cpuevt.ignore = true;
+	WRITE_ONCE(tmc->wakeup, KTIME_MAX);
+	tmc->wakeup_recalc = false;
+
+	walk_groups(&tmigr_active_up, &data, tmc);
+}
+
+/**
+ * tmigr_cpu_activate - set CPU active in timer migration hierarchy
+ *
+ * Call site timer_clear_idle() is called with interrupts disabled
+ */
+void tmigr_cpu_activate(void)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+
+	if (!is_tmigr_enabled() || !tmc->tmgroup || !tmc->online || !tmc->idle)
+		return;
+
+	raw_spin_lock(&tmc->lock);
+	tmc->idle = false;
+	__tmigr_cpu_activate(tmc);
+	raw_spin_unlock(&tmc->lock);
+}
+
+/*
+ * Returns true, if there is nothing to be propagated to the next level
+ *
+ * @data->nextexp is reset to KTIME_MAX; it is reused for the first global event
+ * which needs to be handled by the migrator (in the top level group).
+ *
+ * This is the only place where the group event expiry value is set.
+ */
+static bool tmigr_update_events(struct tmigr_group *group,
+				struct tmigr_group *child,
+				struct tmigr_walk *data)
+{
+	struct tmigr_event *evt, *first_childevt;
+	bool walk_done, remote = data->remote;
+	bool leftmost_change = false;
+	u64 nextexp;
+
+	if (child) {
+		raw_spin_lock(&child->lock);
+		raw_spin_lock_nested(&group->lock, SINGLE_DEPTH_NESTING);
+
+		data->childstate.state = atomic_read(&child->migr_state);
+		data->groupstate.state = atomic_read(&group->migr_state);
+
+		if (data->childstate.active) {
+			walk_done = true;
+			goto unlock;
+		}
+
+		first_childevt = tmigr_next_groupevt(child);
+		nextexp = child->next_expiry;
+		evt = &child->groupevt;
+	} else {
+		nextexp = data->nextexp;
+
+		/*
+		 * Set @data->nextexp to KTIME_MAX; it is reused for the first
+		 * global event which needs to be handled by the migrator (in
+		 * the top level group).
+		 */
+		data->nextexp = KTIME_MAX;
+
+		first_childevt = evt = data->evt;
+
+		/*
+		 * Walking the hierarchy is required in any case when a
+		 * remote expiry was done before. This ensures to not lose
+		 * already queued events in non active groups (see section
+		 * "Required event and timerqueue update after remote
+		 * expiry" in the documentation at the top).
+		 *
+		 * The two call sites which are executed without a remote expiry
+		 * before, are not prevented from propagating changes through
+		 * the hierarchy by the return:
+		 *  - When entering this path by tmigr_new_timer(), @evt->ignore
+		 *    is never set.
+		 *  - tmigr_inactive_up() takes care of the propagation by
+		 *    itself and ignores the return value. But an immediate
+		 *    return is required because nothing has to be done in this
+		 *    level as the event could be ignored.
+		 */
+		if (evt->ignore && !remote)
+			return true;
+
+		raw_spin_lock(&group->lock);
+		data->groupstate.state = atomic_read(&group->migr_state);
+	}
+
+	if (nextexp == KTIME_MAX) {
+		evt->ignore = true;
+
+		/*
+		 * When the next child event could be ignored (nextexp is
+		 * KTIME_MAX) and there was no remote timer handling before or
+		 * the group is already active, there is no need to walk the
+		 * hierarchy even if there is a parent group.
+		 *
+		 * The other way round: even if the event could be ignored, but
+		 * if a remote timer handling was executed before and the group
+		 * is not active, walking the hierarchy is required to not miss
+		 * an enqueued timer in the non active group. The enqueued timer
+		 * of the group needs to be propagated to a higher level to
+		 * ensure it is handled.
+		 */
+		if (!remote || data->groupstate.active) {
+			walk_done = true;
+			goto unlock;
+		}
+	} else {
+		/*
+		 * An update of @evt->cpu and @evt->ignore flag is required only
+		 * when @child is set (the child is equal or higher than lvl0),
+		 * but it doesn't matter if it is written once more to the per
+		 * CPU event; make the update unconditional.
+		 */
+		evt->cpu = first_childevt->cpu;
+		evt->ignore = false;
+	}
+
+	walk_done = !group->parent;
+
+	/*
+	 * If the child event is already queued in the group, remove it from the
+	 * queue when the expiry time changed only.
+	 */
+	if (timerqueue_node_queued(&evt->nextevt)) {
+		if (evt->nextevt.expires == nextexp)
+			goto check_toplvl;
+
+		leftmost_change = timerqueue_getnext(&group->events) == &evt->nextevt;
+		if (!timerqueue_del(&group->events, &evt->nextevt))
+			WRITE_ONCE(group->next_expiry, KTIME_MAX);
+	}
+
+	evt->nextevt.expires = nextexp;
+
+	if (timerqueue_add(&group->events, &evt->nextevt)) {
+		leftmost_change = true;
+		WRITE_ONCE(group->next_expiry, nextexp);
+	}
+
+check_toplvl:
+	if (walk_done && (data->groupstate.migrator == TMIGR_NONE)) {
+		/*
+		 * Nothing to do when first event didn't changed and update was
+		 * done during remote timer handling.
+		 */
+		if (remote && !leftmost_change)
+			goto unlock;
+		/*
+		 * The top level group is idle and it has to be ensured the
+		 * global timers are handled in time. (This could be optimized
+		 * by keeping track of the last global scheduled event and only
+		 * arming it on the CPU if the new event is earlier. Not sure if
+		 * its worth the complexity.)
+		 */
+		data->nextexp = tmigr_next_groupevt_expires(group);
+	}
+
+unlock:
+	raw_spin_unlock(&group->lock);
+
+	if (child)
+		raw_spin_unlock(&child->lock);
+
+	return walk_done;
+}
+
+static bool tmigr_new_timer_up(struct tmigr_group *group,
+			       struct tmigr_group *child,
+			       void *ptr)
+{
+	struct tmigr_walk *data = ptr;
+
+	return tmigr_update_events(group, child, data);
+}
+
+/*
+ * Returns the expiry of the next timer that needs to be handled. KTIME_MAX is
+ * returned, when an active CPU will handle all the timer migration hierarchy
+ * timers.
+ */
+static u64 tmigr_new_timer(struct tmigr_cpu *tmc, u64 nextexp)
+{
+	struct tmigr_walk data = { .evt = &tmc->cpuevt,
+				   .nextexp = nextexp };
+
+	lockdep_assert_held(&tmc->lock);
+
+	if (tmc->remote)
+		return KTIME_MAX;
+
+	tmc->cpuevt.ignore = false;
+	data.remote = false;
+
+	walk_groups(&tmigr_new_timer_up, &data, tmc);
+
+	/* If there is a new first global event, make sure it is handled */
+	return data.nextexp;
+}
+
+static u64 tmigr_handle_remote_cpu(unsigned int cpu, u64 now,
+				   unsigned long jif)
+{
+	struct timer_events tevt;
+	struct tmigr_walk data;
+	struct tmigr_cpu *tmc;
+	u64 next = KTIME_MAX;
+
+	tmc = per_cpu_ptr(&tmigr_cpu, cpu);
+
+	raw_spin_lock_irq(&tmc->lock);
+
+	/*
+	 * The remote CPU is offline or the CPU event does not has to be handled
+	 * (the CPU is active or there is no longer an event to expire) or
+	 * another CPU handles the CPU timers already or the next event was
+	 * already expired - return!
+	 */
+	if (!tmc->online || tmc->remote || tmc->cpuevt.ignore ||
+	    now < tmc->cpuevt.nextevt.expires) {
+		raw_spin_unlock_irq(&tmc->lock);
+		return next;
+	}
+
+	tmc->remote = true;
+	WRITE_ONCE(tmc->wakeup, KTIME_MAX);
+
+	/* Drop the lock to allow the remote CPU to exit idle */
+	raw_spin_unlock_irq(&tmc->lock);
+
+	if (cpu != smp_processor_id())
+		timer_expire_remote(cpu);
+
+	/*
+	 * Lock ordering needs to be preserved - timer_base locks before tmigr
+	 * related locks (see section "Locking rules" in the documentation at
+	 * the top). During fetching the next timer interrupt, also tmc->lock
+	 * needs to be held. Otherwise there is a possible race window against
+	 * the CPU itself when it comes out of idle, updates the first timer in
+	 * the hierarchy and goes back to idle.
+	 *
+	 * timer base locks are dropped as fast as possible: After checking
+	 * whether the remote CPU went offline in the meantime and after
+	 * fetching the next remote timer interrupt. Dropping the locks as fast
+	 * as possible keeps the locking region small and prevents holding
+	 * several (unnecessary) locks during walking the hierarchy for updating
+	 * the timerqueue and group events.
+	 */
+	local_irq_disable();
+	timer_lock_remote_bases(cpu);
+	raw_spin_lock(&tmc->lock);
+
+	/*
+	 * When the CPU went offline in the meantime, no hierarchy walk has to
+	 * be done for updating the queued events, because the walk was
+	 * already done during marking the CPU offline in the hierarchy.
+	 *
+	 * When the CPU is no longer idle, the CPU takes care of the timers and
+	 * also of the timers in the path to the top.
+	 *
+	 * (See also section "Required event and timerqueue update after
+	 * remote expiry" in the documentation at the top)
+	 */
+	if (!tmc->online || !tmc->idle) {
+		timer_unlock_remote_bases(cpu);
+		goto unlock;
+	} else {
+		/* next	event of CPU */
+		fetch_next_timer_interrupt_remote(jif, now, &tevt, cpu);
+	}
+
+	timer_unlock_remote_bases(cpu);
+
+	data.evt = &tmc->cpuevt;
+	data.nextexp = tevt.global;
+	data.remote = true;
+
+	/*
+	 * The update is done even when there is no 'new' global timer pending
+	 * on the remote CPU (see section "Required event and timerqueue update
+	 * after remote expiry" in the documentation at the top)
+	 */
+	walk_groups(&tmigr_new_timer_up, &data, tmc);
+
+	next = data.nextexp;
+
+unlock:
+	tmc->remote = false;
+	raw_spin_unlock_irq(&tmc->lock);
+
+	return next;
+}
+
+static bool tmigr_handle_remote_up(struct tmigr_group *group,
+				   struct tmigr_group *child,
+				   void *ptr)
+{
+	struct tmigr_remote_data *data = ptr;
+	u64 now, next = KTIME_MAX;
+	struct tmigr_event *evt;
+	unsigned long jif;
+	u8 childmask;
+
+	jif = data->basej;
+	now = data->now;
+
+	childmask = data->childmask;
+
+again:
+	/*
+	 * Handle the group only if @childmask is the migrator or if the
+	 * group has no migrator. Otherwise the group is active and is
+	 * handled by its own migrator.
+	 */
+	if (!tmigr_check_migrator(group, childmask))
+		return true;
+
+	raw_spin_lock_irq(&group->lock);
+
+	evt = tmigr_next_expired_groupevt(group, now);
+
+	if (evt) {
+		unsigned int remote_cpu = evt->cpu;
+
+		raw_spin_unlock_irq(&group->lock);
+
+		next = tmigr_handle_remote_cpu(remote_cpu, now, jif);
+
+		/* check if there is another event, that needs to be handled */
+		goto again;
+	} else {
+		raw_spin_unlock_irq(&group->lock);
+	}
+
+	/* Update of childmask for the next level */
+	data->childmask = group->childmask;
+	data->nextexp = next;
+
+	return false;
+}
+
+/**
+ * tmigr_handle_remote - Handle migratable timers on remote idle CPUs
+ *
+ * Called from the timer soft interrupt with interrupts enabled.
+ */
+void tmigr_handle_remote(void)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+	struct tmigr_remote_data data;
+
+	if (!is_tmigr_enabled() || !tmc->tmgroup || !tmc->online)
+		return;
+
+	data.childmask = tmc->childmask;
+	data.nextexp = KTIME_MAX;
+
+	/*
+	 * NOTE: This is a doubled check because the migrator test will be done
+	 * in tmigr_handle_remote_up() anyway. Keep this check to fasten the
+	 * return when nothing has to be done.
+	 */
+	if (!tmigr_check_migrator(tmc->tmgroup, tmc->childmask))
+		return;
+
+	data.now = get_jiffies_update(&data.basej);
+
+	/*
+	 * Update @tmc->wakeup only at the end and do not reset @tmc->wakeup to
+	 * KTIME_MAX. Even if tmc->lock is not held during the whole remote
+	 * handling, tmc->wakeup is fine to be stale as it is called in
+	 * interrupt context and tick_nohz_next_event() is executed in interrupt
+	 * exit path only after processing the last pending interrupt.
+	 */
+
+	__walk_groups(&tmigr_handle_remote_up, &data, tmc);
+
+	raw_spin_lock_irq(&tmc->lock);
+	WRITE_ONCE(tmc->wakeup, data.nextexp);
+	raw_spin_unlock_irq(&tmc->lock);
+}
+
+static bool tmigr_requires_handle_remote_up(struct tmigr_group *group,
+					    struct tmigr_group *child,
+					    void *ptr)
+{
+	struct tmigr_remote_data *data = ptr;
+	u8 childmask;
+
+	childmask = data->childmask;
+
+	/*
+	 * Handle the group only if the child is the migrator or if the group
+	 * has no migrator. Otherwise the group is active and is handled by its
+	 * own migrator.
+	 */
+	if (!tmigr_check_migrator(group, childmask))
+		return true;
+
+	/*
+	 * When there is a parent group and the CPU which triggered the
+	 * hierarchy walk is not active, proceed the walk to reach the top level
+	 * group before reading the next_expiry value.
+	 */
+	if (group->parent && !data->tmc_active)
+		goto out;
+
+	/*
+	 * On 32 bit systems the racy lockless check for next_expiry will
+	 * turn into a random number generator. Therefore do the lockless
+	 * check only on 64 bit systems.
+	 */
+	if (IS_ENABLED(CONFIG_64BIT)) {
+		data->nextexp = READ_ONCE(group->next_expiry);
+		if (data->now >= data->nextexp) {
+			data->check = true;
+			return true;
+		}
+	} else {
+		raw_spin_lock(&group->lock);
+		data->nextexp = group->next_expiry;
+		if (data->now >= group->next_expiry) {
+			data->check = true;
+			raw_spin_unlock(&group->lock);
+			return true;
+		}
+		raw_spin_unlock(&group->lock);
+	}
+
+out:
+	/* Update of childmask for the next level */
+	data->childmask = group->childmask;
+	return false;
+}
+
+/**
+ * tmigr_requires_handle_remote - Check whether remote timer handling is required
+ *
+ * Must be called with interrupts disabled.
+ */
+int tmigr_requires_handle_remote(void)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+	struct tmigr_remote_data data;
+	unsigned int ret = 0;
+	unsigned long jif;
+
+	if (!is_tmigr_enabled() || !tmc->tmgroup || !tmc->online)
+		return ret;
+
+	data.now = get_jiffies_update(&jif);
+	data.childmask = tmc->childmask;
+	data.nextexp = KTIME_MAX;
+	data.tmc_active = !tmc->idle;
+	data.check = false;
+
+	/*
+	 * When the CPU is active, walking the hierarchy to check whether a
+	 * remote expiry is required.
+	 *
+	 * Check is done lockless as interrupts are disabled and @tmc->idle is
+	 * set only by the local CPU.
+	 */
+	if (!tmc->idle) {
+		__walk_groups(&tmigr_requires_handle_remote_up, &data, tmc);
+
+		if (data.nextexp != KTIME_MAX)
+			ret = 1;
+
+		return ret;
+	}
+
+	/*
+	 * When the CPU is idle, check whether the recalculation of @tmc->wakeup
+	 * is required. @tmc->wakeup_recalc is set by a remote CPU which is
+	 * about to go offline, was the last active CPU in the whole timer
+	 * migration hierarchy and now delegates handling of the hierarchy to
+	 * this CPU.
+	 *
+	 * Racy lockless check is valid:
+	 * - @tmc->wakeup_recalc is set by the remote CPU before it issues
+	 *   reschedule IPI.
+	 * - As interrupts are disabled here this CPU will either observe
+	 *   @tmc->wakeup_recalc set before the reschedule IPI can be handled or
+	 *   it will observe it when this function is called again on return
+	 *   from handling the reschedule IPI.
+	 */
+	if (tmc->wakeup_recalc) {
+		raw_spin_lock(&tmc->lock);
+
+		__walk_groups(&tmigr_requires_handle_remote_up, &data, tmc);
+
+		if (data.nextexp != KTIME_MAX)
+			ret = 1;
+
+		WRITE_ONCE(tmc->wakeup, data.nextexp);
+		tmc->wakeup_recalc = false;
+		raw_spin_unlock(&tmc->lock);
+
+		return ret;
+	}
+
+	/*
+	 * When the CPU is idle and @tmc->wakeup is reliable, compare it with
+	 * @data.now. On 64 bit it is valid to do this lockless. On 32 bit
+	 * systems, holding the lock is required to get valid data on concurrent
+	 * writers.
+	 */
+	if (IS_ENABLED(CONFIG_64BIT)) {
+		if (data.now >= READ_ONCE(tmc->wakeup))
+			ret = 1;
+	} else {
+		raw_spin_lock(&tmc->lock);
+		if (data.now >= tmc->wakeup)
+			ret = 1;
+		raw_spin_unlock(&tmc->lock);
+	}
+
+	return ret;
+}
+
+static bool tmigr_inactive_up(struct tmigr_group *group,
+			      struct tmigr_group *child,
+			      void *ptr)
+{
+	union tmigr_state curstate, newstate;
+	struct tmigr_walk *data = ptr;
+	bool walk_done;
+	u8 childmask;
+
+	childmask = data->childmask;
+	newstate = curstate = data->groupstate;
+
+retry:
+	walk_done = true;
+
+	/* Reset active bit when the child is no longer active */
+	if (!data->childstate.active)
+		newstate.active &= ~childmask;
+
+	if (newstate.migrator == childmask) {
+		/*
+		 * Find a new migrator for the group, because the child group is
+		 * idle!
+		 */
+		if (!data->childstate.active) {
+			unsigned long new_migr_bit, active = newstate.active;
+
+			new_migr_bit = find_first_bit(&active, BIT_CNT);
+
+			if (new_migr_bit != BIT_CNT) {
+				newstate.migrator = BIT(new_migr_bit);
+			} else {
+				newstate.migrator = TMIGR_NONE;
+
+				/* Changes need to be propagated */
+				walk_done = false;
+			}
+		}
+	}
+
+	newstate.seq++;
+
+	WARN_ON_ONCE((newstate.migrator != TMIGR_NONE) && !(newstate.active));
+
+	if (!atomic_try_cmpxchg(&group->migr_state, &curstate.state, newstate.state)) {
+		newstate.state = curstate.state;
+
+		/*
+		 * Something changed in the child/parent group in the meantime,
+		 * reread the state of the child and parent; Update of
+		 * data->childstate is required for event handling;
+		 */
+		if (child)
+			data->childstate.state = atomic_read(&child->migr_state);
+
+		goto retry;
+	}
+
+	data->groupstate = newstate;
+	data->remote = false;
+
+	/* Event Handling */
+	tmigr_update_events(group, child, data);
+
+	if (group->parent && (walk_done == false)) {
+		data->childmask = group->childmask;
+		data->childstate = newstate;
+		data->groupstate.state = atomic_read(&group->parent->migr_state);
+	}
+
+	/*
+	 * data->nextexp was set by tmigr_update_events() and contains the
+	 * expiry of the first global event which needs to be handled
+	 */
+	if (data->nextexp != KTIME_MAX) {
+		WARN_ON_ONCE(group->parent);
+		/*
+		 * Top level path - If this CPU is about going offline, wake
+		 * up some random other CPU so it will take over the
+		 * migrator duty and program its timer properly. Ideally
+		 * wake the CPU with the closest expiry time, but that's
+		 * overkill to figure out.
+		 *
+		 * Set wakeup_recalc of remote CPU, to make sure the complete
+		 * idle hierarchy with enqueued timers is reevaluated.
+		 */
+		if (!(this_cpu_ptr(&tmigr_cpu)->online)) {
+			struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+			unsigned int cpu = smp_processor_id();
+			struct tmigr_cpu *tmc_resched;
+
+			cpu = cpumask_any_but(cpu_online_mask, cpu);
+			tmc_resched = per_cpu_ptr(&tmigr_cpu, cpu);
+
+			raw_spin_unlock(&tmc->lock);
+
+			raw_spin_lock(&tmc_resched->lock);
+			tmc_resched->wakeup_recalc = true;
+			raw_spin_unlock(&tmc_resched->lock);
+
+			raw_spin_lock(&tmc->lock);
+			smp_send_reschedule(cpu);
+		}
+	}
+
+	return walk_done;
+}
+
+static u64 __tmigr_cpu_deactivate(struct tmigr_cpu *tmc, u64 nextexp)
+{
+	struct tmigr_walk data = { .childmask = tmc->childmask,
+				   .evt = &tmc->cpuevt,
+				   .nextexp = nextexp,
+				   .childstate.state = 0 };
+
+	data.groupstate.state = atomic_read(&tmc->tmgroup->migr_state);
+
+	/*
+	 * If nextexp is KTIME_MAX, the CPU event will be ignored because the
+	 * local timer expires before the global timer, no global timer is set
+	 * or CPU goes offline.
+	 */
+	if (nextexp != KTIME_MAX)
+		tmc->cpuevt.ignore = false;
+
+	walk_groups(&tmigr_inactive_up, &data, tmc);
+	return data.nextexp;
+}
+
+/**
+ * tmigr_cpu_deactivate - Put current CPU into inactive state
+ * @nextexp:	The next timer event expiry set in the current CPU
+ *
+ * Must be called with interrupts disabled.
+ *
+ * Return: the next event expiry of the current CPU or the next event expiry
+ * from the hierarchy if this CPU is the top level migrator or the hierarchy is
+ * completely idle.
+ */
+u64 tmigr_cpu_deactivate(u64 nextexp)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+	u64 ret;
+
+	if (!is_tmigr_enabled() || !tmc->tmgroup || !tmc->online)
+		return nextexp;
+
+	raw_spin_lock(&tmc->lock);
+
+	/*
+	 * The CPU is already deactivated in the timer migration
+	 * hierarchy. tick_nohz_get_sleep_length() calls tick_nohz_next_event()
+	 * and thereby the timer idle path is executed once more. @tmc->wakeup
+	 * holds the first timer, when the timer migration hierarchy is
+	 * completely idle. If there is no new next expiry value handed in which
+	 * should be inserted into the timer migration hierarchy, the wakeup
+	 * time is returned.
+	 */
+	if (tmc->idle) {
+		ret = READ_ONCE(tmc->wakeup);
+		if (nextexp != KTIME_MAX) {
+			if (nextexp != tmc->cpuevt.nextevt.expires ||
+			    tmc->cpuevt.ignore) {
+				ret = tmigr_new_timer(tmc, nextexp);
+			}
+		} else if (tmc->wakeup_recalc) {
+			struct tmigr_remote_data data;
+
+			data.now = KTIME_MAX;
+			data.childmask = tmc->childmask;
+			data.nextexp = KTIME_MAX;
+			data.tmc_active = false;
+			data.check = false;
+
+			__walk_groups(&tmigr_requires_handle_remote_up, &data, tmc);
+
+			ret = data.nextexp;
+		}
+		tmc->wakeup_recalc = false;
+		goto unlock;
+	}
+
+	ret = __tmigr_cpu_deactivate(tmc, nextexp);
+
+	tmc->idle = true;
+
+unlock:
+	/*
+	 * Make sure the reevaluation of timers in idle path will not miss an
+	 * event.
+	 */
+	WRITE_ONCE(tmc->wakeup, ret);
+
+	raw_spin_unlock(&tmc->lock);
+	return ret;
+}
+
+/**
+ * tmigr_quick_check - Quick check which is called by tick_nohz_next_event
+ *
+ * Returns KTIME_MAX, when it is probable that nothing has to be done (not the
+ * only one in the level 0 group; and if it is the only one in level 0 group,
+ * but there are more than a single group active in top level)
+ *
+ * Returns first expiry of the top level group, when it is the only one in level
+ * 0 and top level also only has a single active child.
+ */
+u64 tmigr_quick_check(void)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+	struct tmigr_group *topgroup;
+	struct list_head lvllist;
+
+	if (!is_tmigr_enabled() || !tmc->tmgroup || !tmc->online || tmc->idle)
+		return KTIME_MAX;
+
+	if (!tmigr_check_migrator_and_lonely(tmc->tmgroup, tmc->childmask))
+		return KTIME_MAX;
+
+	for (int i = tmigr_hierarchy_levels; i > 0 ; i--) {
+		lvllist = tmigr_level_list[i - 1];
+		if (list_is_singular(&lvllist)) {
+			topgroup = list_first_entry(&lvllist, struct tmigr_group, list);
+
+			if (tmigr_check_lonely(topgroup))
+				return READ_ONCE(topgroup->next_expiry);
+		} else {
+			continue;
+		}
+	}
+
+	return KTIME_MAX;
+}
+
+static void tmigr_init_group(struct tmigr_group *group, unsigned int lvl,
+			     int node)
+{
+	union tmigr_state s;
+
+	raw_spin_lock_init(&group->lock);
+
+	group->level = lvl;
+	group->numa_node = lvl < tmigr_crossnode_level ? node : NUMA_NO_NODE;
+
+	group->num_children = 0;
+
+	s.migrator = TMIGR_NONE;
+	s.active = 0;
+	s.seq = 0;
+	atomic_set(&group->migr_state, s.state);
+
+	timerqueue_init_head(&group->events);
+	timerqueue_init(&group->groupevt.nextevt);
+	group->groupevt.nextevt.expires = KTIME_MAX;
+	WRITE_ONCE(group->next_expiry, KTIME_MAX);
+	group->groupevt.ignore = true;
+}
+
+static struct tmigr_group *tmigr_get_group(unsigned int cpu, int node,
+					   unsigned int lvl)
+{
+	struct tmigr_group *tmp, *group = NULL;
+
+	lockdep_assert_held(&tmigr_mutex);
+
+	/* Try to attach to an existing group first */
+	list_for_each_entry(tmp, &tmigr_level_list[lvl], list) {
+		/*
+		 * If @lvl is below the cross numa node level, check whether
+		 * this group belongs to the same numa node.
+		 */
+		if (lvl < tmigr_crossnode_level && tmp->numa_node != node)
+			continue;
+
+		/* Capacity left? */
+		if (tmp->num_children >= TMIGR_CHILDREN_PER_GROUP)
+			continue;
+
+		/*
+		 * TODO: A possible further improvement: Make sure that all CPU
+		 * siblings end up in the same group of the lowest level of the
+		 * hierarchy. Rely on the topology sibling mask would be a
+		 * reasonable solution.
+		 */
+
+		group = tmp;
+		break;
+	}
+
+	if (group)
+		return group;
+
+	/* Allocate and	set up a new group */
+	group = kzalloc_node(sizeof(*group), GFP_KERNEL, node);
+	if (!group)
+		return ERR_PTR(-ENOMEM);
+
+	tmigr_init_group(group, lvl, node);
+
+	/* Setup successful. Add it to the hierarchy */
+	list_add(&group->list, &tmigr_level_list[lvl]);
+	return group;
+}
+
+static void tmigr_connect_child_parent(struct tmigr_group *child,
+				       struct tmigr_group *parent)
+{
+	union tmigr_state childstate;
+
+	raw_spin_lock_irq(&child->lock);
+	raw_spin_lock_nested(&parent->lock, SINGLE_DEPTH_NESTING);
+
+	child->parent = parent;
+	child->childmask = BIT(parent->num_children++);
+
+	raw_spin_unlock(&parent->lock);
+	raw_spin_unlock_irq(&child->lock);
+
+	/*
+	 * To prevent inconsistent states, active children need to be active in
+	 * the new parent as well. Inactive children are already marked inactive
+	 * in the parent group.
+	 */
+	childstate.state = atomic_read(&child->migr_state);
+	if (childstate.migrator != TMIGR_NONE) {
+		struct tmigr_walk data;
+
+		data.childmask = child->childmask;
+		data.groupstate.state = atomic_read(&parent->migr_state);
+
+		/*
+		 * There is only one new level per time. When connecting the
+		 * child and the parent and set the child active when the parent
+		 * is inactive, the parent needs to be the uppermost
+		 * level. Otherwise there went something wrong!
+		 */
+		WARN_ON(!tmigr_active_up(parent, child, &data) && parent->parent);
+	}
+}
+
+static int tmigr_setup_groups(unsigned int cpu, unsigned int node)
+{
+	struct tmigr_group *group, *child, **stack;
+	int top = 0, err = 0, i = 0;
+	struct list_head *lvllist;
+
+	stack = kcalloc(tmigr_hierarchy_levels, sizeof(*stack), GFP_KERNEL);
+	if (!stack)
+		return -ENOMEM;
+
+	do {
+		group = tmigr_get_group(cpu, node, i);
+		if (IS_ERR(group)) {
+			err = PTR_ERR(group);
+			break;
+		}
+
+		top = i;
+		stack[i++] = group;
+
+		/*
+		 * When booting only less CPUs of a system than CPUs are
+		 * available, not all calculated hierarchy levels are required.
+		 *
+		 * The loop is aborted as soon as the highest level, which might
+		 * be different from tmigr_hierarchy_levels, contains only a
+		 * single group.
+		 */
+		if (group->parent || i == tmigr_hierarchy_levels ||
+		    (list_empty(&tmigr_level_list[i]) &&
+		     list_is_singular(&tmigr_level_list[i - 1])))
+			break;
+
+	} while (i < tmigr_hierarchy_levels);
+
+	do {
+		group = stack[--i];
+
+		if (err < 0) {
+			list_del(&group->list);
+			kfree(group);
+			continue;
+		}
+
+		WARN_ON_ONCE(i != group->level);
+
+		/*
+		 * Update tmc -> group / child -> group connection
+		 */
+		if (i == 0) {
+			struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+
+			raw_spin_lock_irq(&group->lock);
+
+			tmc->tmgroup = group;
+			tmc->childmask = BIT(group->num_children++);
+
+			raw_spin_unlock_irq(&group->lock);
+
+			/* There are no children that need to be connected */
+			continue;
+		} else {
+			child = stack[i - 1];
+			tmigr_connect_child_parent(child, group);
+		}
+
+		/* check if uppermost level was newly created */
+		if (top != i)
+			continue;
+
+		WARN_ON_ONCE(top == 0);
+
+		lvllist = &tmigr_level_list[top];
+		if (group->num_children == 1 && list_is_singular(lvllist)) {
+			lvllist = &tmigr_level_list[top - 1];
+			list_for_each_entry(child, lvllist, list) {
+				if (child->parent)
+					continue;
+
+				tmigr_connect_child_parent(child, group);
+			}
+		}
+	} while (i > 0);
+
+	kfree(stack);
+
+	return err;
+}
+
+static int tmigr_add_cpu(unsigned int cpu)
+{
+	int node = cpu_to_node(cpu);
+	int ret;
+
+	mutex_lock(&tmigr_mutex);
+	ret = tmigr_setup_groups(cpu, node);
+	mutex_unlock(&tmigr_mutex);
+
+	return ret;
+}
+
+static int tmigr_cpu_online(unsigned int cpu)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+	unsigned int ret;
+
+	/* First online attempt? Initialize CPU data */
+	if (!tmc->tmgroup) {
+		raw_spin_lock_init(&tmc->lock);
+
+		ret = tmigr_add_cpu(cpu);
+		if (ret < 0)
+			return ret;
+
+		if (tmc->childmask == 0)
+			return -EINVAL;
+
+		timerqueue_init(&tmc->cpuevt.nextevt);
+		tmc->cpuevt.nextevt.expires = KTIME_MAX;
+		tmc->cpuevt.ignore = true;
+		tmc->cpuevt.cpu = cpu;
+
+		tmc->remote = false;
+		tmc->idle = false;
+		WRITE_ONCE(tmc->wakeup, KTIME_MAX);
+	}
+	raw_spin_lock_irq(&tmc->lock);
+	__tmigr_cpu_activate(tmc);
+	tmc->online = true;
+	raw_spin_unlock_irq(&tmc->lock);
+	return 0;
+}
+
+static int tmigr_cpu_offline(unsigned int cpu)
+{
+	struct tmigr_cpu *tmc = this_cpu_ptr(&tmigr_cpu);
+
+	raw_spin_lock_irq(&tmc->lock);
+	tmc->online = false;
+	WRITE_ONCE(tmc->wakeup, KTIME_MAX);
+
+	/*
+	 * CPU has to handle the local events on his own, when on the way to
+	 * offline; Therefore nextevt value is set to KTIME_MAX
+	 */
+	__tmigr_cpu_deactivate(tmc, KTIME_MAX);
+	raw_spin_unlock_irq(&tmc->lock);
+
+	return 0;
+}
+
+static int __init tmigr_init(void)
+{
+	unsigned int cpulvl, nodelvl, cpus_per_node, i;
+	unsigned int nnodes = num_possible_nodes();
+	unsigned int ncpus = num_possible_cpus();
+	int ret = -ENOMEM;
+
+	/* Nothing to do if running on UP */
+	if (ncpus == 1)
+		return 0;
+
+	/*
+	 * Calculate the required hierarchy levels. Unfortunately there is no
+	 * reliable information available, unless all possible CPUs have been
+	 * brought up and all numa nodes are populated.
+	 *
+	 * Estimate the number of levels with the number of possible nodes and
+	 * the number of possible CPUs. Assume CPUs are spread evenly across
+	 * nodes. We cannot rely on cpumask_of_node() because there only already
+	 * online CPUs are considered.
+	 */
+	cpus_per_node = DIV_ROUND_UP(ncpus, nnodes);
+
+	/* Calc the hierarchy levels required to hold the CPUs of a node */
+	cpulvl = DIV_ROUND_UP(order_base_2(cpus_per_node),
+			      ilog2(TMIGR_CHILDREN_PER_GROUP));
+
+	/* Calculate the extra levels to connect all nodes */
+	nodelvl = DIV_ROUND_UP(order_base_2(nnodes),
+			       ilog2(TMIGR_CHILDREN_PER_GROUP));
+
+	tmigr_hierarchy_levels = cpulvl + nodelvl;
+
+	/*
+	 * If a numa node spawns more than one CPU level group then the next
+	 * level(s) of the hierarchy contains groups which handle all CPU groups
+	 * of the same numa node. The level above goes across numa nodes. Store
+	 * this information for the setup code to decide when node matching is
+	 * not longer required.
+	 */
+	tmigr_crossnode_level = cpulvl;
+
+	tmigr_level_list = kcalloc(tmigr_hierarchy_levels, sizeof(struct list_head), GFP_KERNEL);
+	if (!tmigr_level_list)
+		goto err;
+
+	for (i = 0; i < tmigr_hierarchy_levels; i++)
+		INIT_LIST_HEAD(&tmigr_level_list[i]);
+
+	pr_info("Timer migration: %d hierarchy levels; %d children per group;"
+		" %d crossnode level\n",
+		tmigr_hierarchy_levels, TMIGR_CHILDREN_PER_GROUP,
+		tmigr_crossnode_level);
+
+	ret = cpuhp_setup_state(CPUHP_AP_TMIGR_ONLINE, "tmigr:online",
+				tmigr_cpu_online, tmigr_cpu_offline);
+	if (ret)
+		goto err;
+
+	static_branch_enable(&tmigr_enabled);
+
+	return 0;
+
+err:
+	pr_err("Timer migration setup failed\n");
+	return ret;
+}
+late_initcall(tmigr_init);
diff --git a/kernel/time/timer_migration.h b/kernel/time/timer_migration.h
new file mode 100644
index 000000000000..01c08a5dbb49
--- /dev/null
+++ b/kernel/time/timer_migration.h
@@ -0,0 +1,144 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef _KERNEL_TIME_MIGRATION_H
+#define _KERNEL_TIME_MIGRATION_H
+
+/* Per group capacity. Must be a power of 2! */
+#define TMIGR_CHILDREN_PER_GROUP 8
+
+/**
+ * struct tmigr_event - a timer event associated to a CPU
+ * @nextevt:	The node to enqueue an event in the parent group queue
+ * @cpu:	The CPU to which this event belongs
+ * @ignore:	Hint whether the event could be ignored; it is set when
+ *		CPU or group is active;
+ */
+struct tmigr_event {
+	struct timerqueue_node	nextevt;
+	unsigned int		cpu;
+	bool			ignore;
+};
+
+/**
+ * struct tmigr_group - timer migration hierarchy group
+ * @lock:		Lock protecting the event information and group hierarchy
+ *			information during setup
+ * @migr_state:		State of group (see union tmigr_state)
+ * @parent:		Pointer to parent group
+ * @groupevt:		Next event of group which is only used when group is
+ *			!active. The group event is then queued into parent
+ *			timer queue.
+ *			Ignore bit of @groupevt is set when group is active.
+ * @next_expiry:	Base monotonic expiry time of next event of group;
+ *			Used for racy lockless check whether remote expiry is
+ *			required; it is always reliable
+ * @events:		Timer queue for child events queued in the group
+ * @childmask:		childmask of group in parent group; is set during
+ *			setup and will never change; could be read lockless
+ * @level:		Hierarchy level of group; Required during setup and
+ *			when DEBUG is defined
+ * @list:		List head that is added to per level
+ *			tmigr_level_list; is required during setup when a
+ *			new group needs to be connected to the existing
+ *			hierarchy groups
+ * @numa_node:		Is set to numa node when level < tmigr_crossnode_level;
+ *			otherwise it is set to NUMA_NO_NODE; Required for
+ *			setup only to make sure CPUs and groups are per
+ *			numa node as long as level < tmigr_crossnode_level
+ * @num_children:	Counter of group children to make sure group is only filled
+ *			with TMIGR_CHILDREN_PER_GROUP; Required for setup only
+ */
+struct tmigr_group {
+	raw_spinlock_t		lock;
+	atomic_t		migr_state;
+	struct tmigr_group	*parent;
+	struct tmigr_event	groupevt;
+	u64			next_expiry;
+	struct timerqueue_head	events;
+	u8			childmask;
+	unsigned int		level;
+	struct list_head	list;
+	int			numa_node;
+	unsigned int		num_children;
+};
+
+/**
+ * struct tmigr_cpu - timer migration per CPU group
+ * @lock:		Lock protecting tmigr_cpu group information
+ * @online:		Indicates whether CPU is online; In deactivate path it
+ *			is required to know whether the migrator in top level
+ *			group is on the way to go offline when a timer is
+ *			pending. Then another online CPU needs to be rescheduled
+ *			to make sure timers are handled properly; Furthermore
+ *			the information is required in CPU hotplug path as CPU is
+ *			able to go idle before timer migration hierarchy hotplug
+ *			AP is reached. During this phase CPU has to handle
+ *			global timers by its own and does not act as migrator.
+ * @idle:		Indicates whether CPU is idle in timer migration
+ *			hierarchy
+ * @remote:		Is set when timers of CPU are expired remote
+ * @wakeup_recalc:	Indicates, whether a recalculation of @wakeup value is
+ *			required. It is only used when CPU is marked idle in
+ *			timer migration hierarchy.
+ * @tmgroup:		Pointer to parent group
+ * @childmask:		childmask of tmigr_cpu in parent group
+ * @wakeup:		Stores the first timer when the timer migration
+ *			hierarchy is completely idle and remote expiry was done;
+ *			is returned to timer code when tmigr_cpu_deactive() is
+ *			called and group is idle; it is only valid, when
+ *			@wakeup_recalc is not set;
+ * @cpuevt:		CPU event which could be queued into parent group
+ */
+struct tmigr_cpu {
+	raw_spinlock_t		lock;
+	bool			online;
+	bool			idle;
+	bool			remote;
+	bool			wakeup_recalc;
+	struct tmigr_group	*tmgroup;
+	u8			childmask;
+	u64			wakeup;
+	struct tmigr_event	cpuevt;
+};
+
+/**
+ * union tmigr_state - state of tmigr_group
+ * @state:	Combined version of the state - only used for atomic
+ *		read/cmpxchg function
+ * @struct:	Split version of the state - only use the struct members to
+ *		update information to stay independent of endianness
+ */
+union tmigr_state {
+	u32 state;
+	/**
+	 * struct - split state of tmigr_group
+	 * @active:	Contains each childmask bit of active children
+	 * @migrator:	Contains childmask of child which is migrator
+	 * @seq:	Sequence counter needs to be increased when update
+	 *		to the tmigr_state is done. It prevents a race when
+	 *		updates in child groups are propagated in changed
+	 *		order. Detailed information about the scenario is
+	 *		given in documentation at the begin of
+	 *		timer_migration.c.
+	 */
+	struct {
+		u8	active;
+		u8	migrator;
+		u16	seq;
+	} __packed;
+};
+
+#if defined(CONFIG_SMP) && defined(CONFIG_NO_HZ_COMMON)
+extern void tmigr_handle_remote(void);
+extern int tmigr_requires_handle_remote(void);
+extern void tmigr_cpu_activate(void);
+extern u64 tmigr_cpu_deactivate(u64 nextevt);
+extern u64 tmigr_quick_check(void);
+#else
+static inline void tmigr_handle_remote(void) { }
+static inline int tmigr_requires_handle_remote(void) { return 0; }
+static inline void tmigr_cpu_activate(void) { }
+static inline u64 tmigr_cpu_deactivate(u64 nextevt) { return KTIME_MAX; }
+static inline u64 tmigr_quick_check(void) { return KTIME_MAX; };
+#endif
+
+#endif
-- 
2.39.2