[PATCH v3 10/27] staging: iio: resolver: ad2s1210: use regmap for config registers
From: David Lechner
Date: Fri Sep 29 2023 - 13:50:24 EST
From: David Lechner <david@xxxxxxxxxxxxxx>
From: David Lechner <dlechner@xxxxxxxxxxxx>
This makes use of the regmap API to read and write the configuration
registers. This simplifies code quite a bit and makes it safer
(previously, it was easy to write a bad value to the config registers
which causes the chip to lock up and need to be reset).
This chip has multiple modes of operation. In normal mode, we do not use
regmap since there is no addressing - data is just bitshifted out during
the SPI read. In config mode, we use regmap since it requires writing
the address (with read/write flag) before reading and writing.
We don't use the lock provided by the regmap because we need to also
synchronize with the normal mode SPI reads and with the various GPIOs.
There is also a quirk when reading registers (other than the fault
register). If the address/data bit is set in the value read, then it
indicates there is a configuration parity error and the data is not
valid. Previously, this was checked in a few places, but not
consistently. Now, we always check it in the regmap read function.
Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
---
v3 changes:
* Expanded description in commit message.
* Fixed multiline comment style.
* Replaced use of AD2S1210_DEF_CONTROL with FIELD_PREP().
* Removed unrelated `if (reg < 0)` change.
drivers/staging/iio/resolver/ad2s1210.c | 259 +++++++++++++++++++-------------
1 file changed, 155 insertions(+), 104 deletions(-)
diff --git a/drivers/staging/iio/resolver/ad2s1210.c b/drivers/staging/iio/resolver/ad2s1210.c
index c8723b6f3a3b..0663a51d04ad 100644
--- a/drivers/staging/iio/resolver/ad2s1210.c
+++ b/drivers/staging/iio/resolver/ad2s1210.c
@@ -5,6 +5,8 @@
* Copyright (c) 2010-2010 Analog Devices Inc.
* Copyright (c) 2023 BayLibre, SAS
*/
+#include <linux/bitfield.h>
+#include <linux/bits.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/device.h>
@@ -12,6 +14,7 @@
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/of.h>
+#include <linux/regmap.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
#include <linux/sysfs.h>
@@ -22,21 +25,17 @@
#define DRV_NAME "ad2s1210"
-#define AD2S1210_DEF_CONTROL 0x7E
-
-#define AD2S1210_MSB_IS_HIGH 0x80
-#define AD2S1210_MSB_IS_LOW 0x7F
-#define AD2S1210_PHASE_LOCK_RANGE_44 0x20
-#define AD2S1210_ENABLE_HYSTERESIS 0x10
-#define AD2S1210_SET_ENRES1 0x08
-#define AD2S1210_SET_ENRES0 0x04
-#define AD2S1210_SET_RES1 0x02
-#define AD2S1210_SET_RES0 0x01
-
-#define AD2S1210_SET_RESOLUTION (AD2S1210_SET_RES1 | AD2S1210_SET_RES0)
-
-#define AD2S1210_REG_POSITION 0x80
-#define AD2S1210_REG_VELOCITY 0x82
+/* control register flags */
+#define AD2S1210_ADDRESS_DATA BIT(7)
+#define AD2S1210_PHASE_LOCK_RANGE_44 BIT(5)
+#define AD2S1210_ENABLE_HYSTERESIS BIT(4)
+#define AD2S1210_SET_ENRES GENMASK(3, 2)
+#define AD2S1210_SET_RES GENMASK(1, 0)
+
+#define AD2S1210_REG_POSITION_MSB 0x80
+#define AD2S1210_REG_POSITION_LSB 0x81
+#define AD2S1210_REG_VELOCITY_MSB 0x82
+#define AD2S1210_REG_VELOCITY_LSB 0x83
#define AD2S1210_REG_LOS_THRD 0x88
#define AD2S1210_REG_DOS_OVR_THRD 0x89
#define AD2S1210_REG_DOS_MIS_THRD 0x8A
@@ -92,6 +91,8 @@ struct ad2s1210_state {
struct mutex lock;
struct spi_device *sdev;
struct gpio_desc *gpios[5];
+ /** Used to access config registers. */
+ struct regmap *regmap;
/** The external oscillator frequency in Hz. */
unsigned long clkin_hz;
unsigned int fexcit;
@@ -120,24 +121,51 @@ static inline void ad2s1210_set_mode(enum ad2s1210_mode mode,
st->mode = mode;
}
-/* write 1 bytes (address or data) to the chip */
-static int ad2s1210_config_write(struct ad2s1210_state *st, u8 data)
+/*
+ * Writes the given data to the given register address.
+ *
+ * If the mode is configurable, the device will first be placed in
+ * configuration mode.
+ */
+static int ad2s1210_regmap_reg_write(void *context, unsigned int reg,
+ unsigned int val)
{
- int ret;
+ struct ad2s1210_state *st = context;
+ struct spi_transfer xfers[] = {
+ {
+ .len = 1,
+ .rx_buf = &st->rx[0],
+ .tx_buf = &st->tx[0],
+ .cs_change = 1,
+ }, {
+ .len = 1,
+ .rx_buf = &st->rx[1],
+ .tx_buf = &st->tx[1],
+ },
+ };
+
+ /* values can only be 7 bits, the MSB indicates an address */
+ if (val & ~0x7F)
+ return -EINVAL;
+
+ st->tx[0] = reg;
+ st->tx[1] = val;
ad2s1210_set_mode(MOD_CONFIG, st);
- st->tx[0] = data;
- ret = spi_write(st->sdev, st->tx, 1);
- if (ret < 0)
- return ret;
- return 0;
+ return spi_sync_transfer(st->sdev, xfers, ARRAY_SIZE(xfers));
}
-/* read value from one of the registers */
-static int ad2s1210_config_read(struct ad2s1210_state *st,
- unsigned char address)
+/*
+ * Reads value from one of the registers.
+ *
+ * If the mode is configurable, the device will first be placed in
+ * configuration mode.
+ */
+static int ad2s1210_regmap_reg_read(void *context, unsigned int reg,
+ unsigned int *val)
{
+ struct ad2s1210_state *st = context;
struct spi_transfer xfers[] = {
{
.len = 1,
@@ -150,22 +178,36 @@ static int ad2s1210_config_read(struct ad2s1210_state *st,
.tx_buf = &st->tx[1],
},
};
- int ret = 0;
+ int ret;
ad2s1210_set_mode(MOD_CONFIG, st);
- st->tx[0] = address | AD2S1210_MSB_IS_HIGH;
+ st->tx[0] = reg;
+ /*
+ * Must be valid register address here otherwise this could write data.
+ * It doesn't matter which one.
+ */
st->tx[1] = AD2S1210_REG_FAULT;
- ret = spi_sync_transfer(st->sdev, xfers, 2);
+
+ ret = spi_sync_transfer(st->sdev, xfers, ARRAY_SIZE(xfers));
if (ret < 0)
return ret;
- return st->rx[1];
+ /*
+ * If the D7 bit is set on any read/write register, it indicates a
+ * parity error. The fault register is read-only and the D7 bit means
+ * something else there.
+ */
+ if (reg != AD2S1210_REG_FAULT && st->rx[1] & AD2S1210_ADDRESS_DATA)
+ return -EBADMSG;
+
+ *val = st->rx[1];
+
+ return 0;
}
static inline
int ad2s1210_update_frequency_control_word(struct ad2s1210_state *st)
{
- int ret;
unsigned char fcw;
fcw = (unsigned char)(st->fexcit * (1 << 15) / st->clkin_hz);
@@ -174,11 +216,7 @@ int ad2s1210_update_frequency_control_word(struct ad2s1210_state *st)
return -ERANGE;
}
- ret = ad2s1210_config_write(st, AD2S1210_REG_EXCIT_FREQ);
- if (ret < 0)
- return ret;
-
- return ad2s1210_config_write(st, fcw);
+ return regmap_write(st->regmap, AD2S1210_REG_EXCIT_FREQ, fcw);
}
static const int ad2s1210_res_pins[4][2] = {
@@ -195,13 +233,7 @@ static inline void ad2s1210_set_resolution_pin(struct ad2s1210_state *st)
static inline int ad2s1210_soft_reset(struct ad2s1210_state *st)
{
- int ret;
-
- ret = ad2s1210_config_write(st, AD2S1210_REG_SOFT_RESET);
- if (ret < 0)
- return ret;
-
- return ad2s1210_config_write(st, 0x0);
+ return regmap_write(st->regmap, AD2S1210_REG_SOFT_RESET, 0);
}
static ssize_t ad2s1210_show_fexcit(struct device *dev,
@@ -246,12 +278,13 @@ static ssize_t ad2s1210_show_control(struct device *dev,
char *buf)
{
struct ad2s1210_state *st = iio_priv(dev_to_iio_dev(dev));
+ unsigned int value;
int ret;
mutex_lock(&st->lock);
- ret = ad2s1210_config_read(st, AD2S1210_REG_CONTROL);
+ ret = regmap_read(st->regmap, AD2S1210_REG_CONTROL, &value);
mutex_unlock(&st->lock);
- return ret < 0 ? ret : sprintf(buf, "0x%x\n", ret);
+ return ret < 0 ? ret : sprintf(buf, "0x%x\n", value);
}
static ssize_t ad2s1210_store_control(struct device *dev,
@@ -268,25 +301,13 @@ static ssize_t ad2s1210_store_control(struct device *dev,
return -EINVAL;
mutex_lock(&st->lock);
- ret = ad2s1210_config_write(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
- data = udata & AD2S1210_MSB_IS_LOW;
- ret = ad2s1210_config_write(st, data);
+ data = udata & ~AD2S1210_ADDRESS_DATA;
+ ret = regmap_write(st->regmap, AD2S1210_REG_CONTROL, data);
if (ret < 0)
goto error_ret;
- ret = ad2s1210_config_read(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
- if (ret & AD2S1210_MSB_IS_HIGH) {
- ret = -EIO;
- dev_err(dev,
- "ad2s1210: write control register fail\n");
- goto error_ret;
- }
st->resolution =
- ad2s1210_resolution_value[data & AD2S1210_SET_RESOLUTION];
+ ad2s1210_resolution_value[data & AD2S1210_SET_RES];
ad2s1210_set_resolution_pin(st);
ret = len;
st->hysteresis = !!(data & AD2S1210_ENABLE_HYSTERESIS);
@@ -319,30 +340,17 @@ static ssize_t ad2s1210_store_resolution(struct device *dev,
dev_err(dev, "ad2s1210: resolution out of range\n");
return -EINVAL;
}
+
+ data = (udata - 10) >> 1;
+
mutex_lock(&st->lock);
- ret = ad2s1210_config_read(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
- data = ret;
- data &= ~AD2S1210_SET_RESOLUTION;
- data |= (udata - 10) >> 1;
- ret = ad2s1210_config_write(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
- ret = ad2s1210_config_write(st, data & AD2S1210_MSB_IS_LOW);
- if (ret < 0)
- goto error_ret;
- ret = ad2s1210_config_read(st, AD2S1210_REG_CONTROL);
+ ret = regmap_update_bits(st->regmap, AD2S1210_REG_CONTROL,
+ AD2S1210_SET_RES, data);
if (ret < 0)
goto error_ret;
- data = ret;
- if (data & AD2S1210_MSB_IS_HIGH) {
- ret = -EIO;
- dev_err(dev, "ad2s1210: setting resolution fail\n");
- goto error_ret;
- }
+
st->resolution =
- ad2s1210_resolution_value[data & AD2S1210_SET_RESOLUTION];
+ ad2s1210_resolution_value[data & AD2S1210_SET_RES];
ad2s1210_set_resolution_pin(st);
ret = len;
error_ret:
@@ -355,13 +363,14 @@ static ssize_t ad2s1210_show_fault(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct ad2s1210_state *st = iio_priv(dev_to_iio_dev(dev));
+ unsigned int value;
int ret;
mutex_lock(&st->lock);
- ret = ad2s1210_config_read(st, AD2S1210_REG_FAULT);
+ ret = regmap_read(st->regmap, AD2S1210_REG_FAULT, &value);
mutex_unlock(&st->lock);
- return ret < 0 ? ret : sprintf(buf, "0x%02x\n", ret);
+ return ret < 0 ? ret : sprintf(buf, "0x%02x\n", value);
}
static ssize_t ad2s1210_clear_fault(struct device *dev,
@@ -370,6 +379,7 @@ static ssize_t ad2s1210_clear_fault(struct device *dev,
size_t len)
{
struct ad2s1210_state *st = iio_priv(dev_to_iio_dev(dev));
+ unsigned int value;
int ret;
mutex_lock(&st->lock);
@@ -377,7 +387,7 @@ static ssize_t ad2s1210_clear_fault(struct device *dev,
/* delay (2 * tck + 20) nano seconds */
udelay(1);
gpiod_set_value(st->gpios[AD2S1210_SAMPLE], 1);
- ret = ad2s1210_config_read(st, AD2S1210_REG_FAULT);
+ ret = regmap_read(st->regmap, AD2S1210_REG_FAULT, &value);
if (ret < 0)
goto error_ret;
gpiod_set_value(st->gpios[AD2S1210_SAMPLE], 0);
@@ -394,13 +404,14 @@ static ssize_t ad2s1210_show_reg(struct device *dev,
{
struct ad2s1210_state *st = iio_priv(dev_to_iio_dev(dev));
struct iio_dev_attr *iattr = to_iio_dev_attr(attr);
+ unsigned int value;
int ret;
mutex_lock(&st->lock);
- ret = ad2s1210_config_read(st, iattr->address);
+ ret = regmap_read(st->regmap, iattr->address, &value);
mutex_unlock(&st->lock);
- return ret < 0 ? ret : sprintf(buf, "%d\n", ret);
+ return ret < 0 ? ret : sprintf(buf, "%d\n", value);
}
static ssize_t ad2s1210_store_reg(struct device *dev,
@@ -415,12 +426,9 @@ static ssize_t ad2s1210_store_reg(struct device *dev,
ret = kstrtou8(buf, 10, &data);
if (ret)
return -EINVAL;
+
mutex_lock(&st->lock);
- ret = ad2s1210_config_write(st, iattr->address);
- if (ret < 0)
- goto error_ret;
- ret = ad2s1210_config_write(st, data & AD2S1210_MSB_IS_LOW);
-error_ret:
+ ret = regmap_write(st->regmap, iattr->address, data);
mutex_unlock(&st->lock);
return ret < 0 ? ret : len;
}
@@ -587,22 +595,15 @@ static int ad2s1210_initial(struct ad2s1210_state *st)
mutex_lock(&st->lock);
ad2s1210_set_resolution_pin(st);
- ret = ad2s1210_config_write(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
- data = AD2S1210_DEF_CONTROL & ~(AD2S1210_SET_RESOLUTION);
- data |= (st->resolution - 10) >> 1;
- ret = ad2s1210_config_write(st, data);
- if (ret < 0)
- goto error_ret;
- ret = ad2s1210_config_read(st, AD2S1210_REG_CONTROL);
- if (ret < 0)
- goto error_ret;
+ /* Use default config register value plus resolution from devicetree. */
+ data = FIELD_PREP(AD2S1210_PHASE_LOCK_RANGE_44, 1);
+ data |= FIELD_PREP(AD2S1210_ENABLE_HYSTERESIS, 1);
+ data |= FIELD_PREP(AD2S1210_SET_ENRES, 0x3);
+ data |= FIELD_PREP(AD2S1210_SET_RES, (st->resolution - 10) >> 1);
- if (ret & AD2S1210_MSB_IS_HIGH) {
- ret = -EIO;
+ ret = regmap_write(st->regmap, AD2S1210_REG_CONTROL, data);
+ if (ret < 0)
goto error_ret;
- }
ret = ad2s1210_update_frequency_control_word(st);
if (ret < 0)
@@ -656,6 +657,52 @@ static int ad2s1210_setup_gpios(struct ad2s1210_state *st)
return 0;
}
+static const struct regmap_range ad2s1210_regmap_readable_ranges[] = {
+ regmap_reg_range(AD2S1210_REG_POSITION_MSB, AD2S1210_REG_VELOCITY_LSB),
+ regmap_reg_range(AD2S1210_REG_LOS_THRD, AD2S1210_REG_LOT_LOW_THRD),
+ regmap_reg_range(AD2S1210_REG_EXCIT_FREQ, AD2S1210_REG_CONTROL),
+ regmap_reg_range(AD2S1210_REG_FAULT, AD2S1210_REG_FAULT),
+};
+
+static const struct regmap_access_table ad2s1210_regmap_rd_table = {
+ .yes_ranges = ad2s1210_regmap_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(ad2s1210_regmap_readable_ranges),
+};
+
+static const struct regmap_range ad2s1210_regmap_writeable_ranges[] = {
+ regmap_reg_range(AD2S1210_REG_LOS_THRD, AD2S1210_REG_LOT_LOW_THRD),
+ regmap_reg_range(AD2S1210_REG_EXCIT_FREQ, AD2S1210_REG_CONTROL),
+ regmap_reg_range(AD2S1210_REG_SOFT_RESET, AD2S1210_REG_SOFT_RESET),
+ regmap_reg_range(AD2S1210_REG_FAULT, AD2S1210_REG_FAULT),
+};
+
+static const struct regmap_access_table ad2s1210_regmap_wr_table = {
+ .yes_ranges = ad2s1210_regmap_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(ad2s1210_regmap_writeable_ranges),
+};
+
+static int ad2s1210_setup_regmap(struct ad2s1210_state *st)
+{
+ struct device *dev = &st->sdev->dev;
+ const struct regmap_config config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .disable_locking = true,
+ .reg_read = ad2s1210_regmap_reg_read,
+ .reg_write = ad2s1210_regmap_reg_write,
+ .rd_table = &ad2s1210_regmap_rd_table,
+ .wr_table = &ad2s1210_regmap_wr_table,
+ .can_sleep = true,
+ };
+
+ st->regmap = devm_regmap_init(dev, NULL, st, &config);
+ if (IS_ERR(st->regmap))
+ return dev_err_probe(dev, PTR_ERR(st->regmap),
+ "failed to allocate register map\n");
+
+ return 0;
+}
+
static int ad2s1210_probe(struct spi_device *spi)
{
struct iio_dev *indio_dev;
@@ -682,6 +729,10 @@ static int ad2s1210_probe(struct spi_device *spi)
if (ret < 0)
return ret;
+ ret = ad2s1210_setup_regmap(st);
+ if (ret < 0)
+ return ret;
+
ret = ad2s1210_initial(st);
if (ret < 0)
return ret;
--
2.42.0