[PATCH AUTOSEL 5.15 15/18] scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command

[Sasha Levin]

From: Michal Grzedzicki <mge@xxxxxxxx>

[ Upstream commit 71996bb835aed58c7ec4967be1d05190a27339ec ]

Some cards have more than one SAS address. Using an incorrect address
causes communication issues with some devices like expanders.

Closes: https://lore.kernel.org/linux-kernel/A57AEA84-5CA0-403E-8053-106033C73C70@xxxxxx/
Signed-off-by: Michal Grzedzicki <mge@xxxxxxxx>
Link: https://lore.kernel.org/r/20230913155611.3183612-1-mge@xxxxxxxx
Acked-by: Jack Wang <jinpu.wang@xxxxxxxxx>
Signed-off-by: Martin K. Petersen <martin.petersen@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
 drivers/scsi/pm8001/pm8001_hwi.c | 2 +-
 drivers/scsi/pm8001/pm80xx_hwi.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/pm8001/pm8001_hwi.c b/drivers/scsi/pm8001/pm8001_hwi.c
index 32fc450bf84b4..352705e023c83 100644
--- a/drivers/scsi/pm8001/pm8001_hwi.c
+++ b/drivers/scsi/pm8001/pm8001_hwi.c
@@ -4402,7 +4402,7 @@ pm8001_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id)
 	payload.sas_identify.dev_type = SAS_END_DEVICE;
 	payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
 	memcpy(payload.sas_identify.sas_addr,
-		pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+		&pm8001_ha->phy[phy_id].dev_sas_addr, SAS_ADDR_SIZE);
 	payload.sas_identify.phy_id = phy_id;
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
 			sizeof(payload), 0);
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c
index 04746df26c6c9..ea305d093c871 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -4814,7 +4814,7 @@ pm80xx_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id)
 	payload.sas_identify.dev_type = SAS_END_DEVICE;
 	payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
 	memcpy(payload.sas_identify.sas_addr,
-	  &pm8001_ha->sas_addr, SAS_ADDR_SIZE);
+		&pm8001_ha->phy[phy_id].dev_sas_addr, SAS_ADDR_SIZE);
 	payload.sas_identify.phy_id = phy_id;
 	ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
 			sizeof(payload), 0);
-- 
2.40.1