[RFC PATCH v2 net-next 04/15] phy: allow querying the address of protocol converters through phy_get_status()

[Vladimir Oltean]

The bit stream handled by a SerDes lane needs protocol converters to be
usable for Ethernet. On Freescale/NXP SoCs, those protocol converters
are located on the internal MDIO buses of the Ethernet MACs that need
them.

The location on that MDIO bus, on these SoCs, is not fixed, but given by
some control registers of the SerDes block itself.

Because no one modifies those addresses from the power-on default, so
far we've relied on hardcoding the default values in the device trees,
resulting in something like this:

		pcs_mdio1: mdio@8c07000 {
			compatible = "fsl,fman-memac-mdio";

			pcs1: ethernet-phy@0 {
				reg = <0>;
			};
		};

where the "reg" of "pcs1" can actually be retrieved from "serdes_1".

That was for the PCS. For AN/LT blocks, that can also be done, but the
MAC to PCS to AN/LT block mapping is non-trivial and extremely easy to
get wrong, which will confuse and frustrate any device tree writers.

The proposal is to take advantage of the fact that these protocol
converters *are* discoverable, and to side-step that entire device tree
mapping issue by not putting them in the device tree at all. So, one of
the consumers of the SerDes PHY uses the phy_get_status() API to figure
out the address on the MDIO bus, it also has a reference to the MDIO bus
=> it can create the mdio_device in a non OF-based manner.

Signed-off-by: Vladimir Oltean <vladimir.oltean@xxxxxxx>
---
v1->v2: patch is new

 include/linux/phy/phy.h | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
index f1f03fa66943..ee721067517b 100644
--- a/include/linux/phy/phy.h
+++ b/include/linux/phy/phy.h
@@ -56,6 +56,33 @@ enum phy_media {
 enum phy_status_type {
 	/* Valid for PHY_MODE_ETHERNET and PHY_MODE_ETHTOOL */
 	PHY_STATUS_CDR_LOCK,
+	PHY_STATUS_PCVT_ADDR,
+};
+
+/* enum phy_pcvt_type - PHY protocol converter type
+ *
+ * @PHY_PCVT_ETHERNET_PCS: Ethernet Physical Coding Sublayer, top-most layer of
+ *			   an Ethernet PHY. Connects through MII to the MAC,
+ *			   and handles link status detection and the conversion
+ *			   of MII signals to link-specific code words (8b/10b,
+ *			   64b/66b etc).
+ * @PHY_PCVT_ETHERNET_ANLT: Ethernet Auto-Negotiation and Link Training,
+ *			    bottom-most layer of an Ethernet PHY, beneath the
+ *			    PMA and PMD. Its activity is only visible on the
+ *			    physical medium, and it is responsible for
+ *			    selecting the most adequate PCS/PMA/PMD set that
+ *			    can operate on that medium.
+ */
+enum phy_pcvt_type {
+	PHY_PCVT_ETHERNET_PCS,
+	PHY_PCVT_ETHERNET_ANLT,
+};
+
+struct phy_status_opts_pcvt {
+	enum phy_pcvt_type type;
+	union {
+		unsigned int mdio;
+	} addr;
 };
 
 /* If the CDR (Clock and Data Recovery) block is able to lock onto the RX bit
@@ -71,9 +98,11 @@ struct phy_status_opts_cdr {
  * union phy_status_opts - Opaque generic phy status
  *
  * @cdr:	Configuration set applicable for PHY_STATUS_CDR_LOCK.
+ * @pcvt:	Configuration set applicable for PHY_STATUS_PCVT_ADDR.
  */
 union phy_status_opts {
 	struct phy_status_opts_cdr		cdr;
+	struct phy_status_opts_pcvt		pcvt;
 };
 
 /**
-- 
2.34.1