Re: [PATCH V6 1/3] mfd: Add support for UP board CPLD/FPGA
From: Lee Jones
Date: Thu Sep 21 2023 - 16:03:11 EST
On Fri, 15 Sep 2023, larry.lai wrote:
> The UP Squared board <http://www.upboard.com> implements certain
> features (pin control, onboard LEDs or CEC) through an on-board CPLD/FPGA.
>
> This driver implements the line protocol to read and write registers
> from the FPGA through regmap. The register address map is also included.
>
> The UP Boards provide a few I/O pin headers (for both GPIO and
> functions), including a 40-pin Raspberry Pi compatible header.
>
> This patch implements support for the FPGA-based pin controller that
> manages direction and enable state for those header pins.
>
> Partial support UP boards:
> * UP core + CREX
> * UP core + CRST02
>
> Reported-by: kernel test robot <lkp@xxxxxxxxx>
> Signed-off-by: Gary Wang <garywang@xxxxxxxxxxxx>
> Signed-off-by: larry.lai <larry.lai@xxxxxxxxxxxxxxx>
> ---
> PATCH V5 -> PATCH V6
> (1) Fixed kernel test robot compiler warning.
> PATCH V4 -> PATCH V5
> (1) Refer 2023/05/25 Lee Jones review, cleaned up coding style
> and addressed review comments.
> (2) Synchronizing upboard github to v1.0.5 tag.
> RFC 2023/04/25 -> PATCH V4
> (1) Fixed kernel test robot compiler warning.
> (2) Remove mistakes with wrong Reviewed-by tags.
> RFC 2022/11/23 -> RFC 2023/04/25
> (1) Refer 2022/12/08 Andy Shevchenko review, cleaned up coding style
> and addressed review comments.
> PATCH V3 -> RFC 2022/11/23:
> (1) Refer 2022/11/16 Lee Jones review, cleaned up coding style and
> addressed review comments.
> (2) Description on the UP Boards FPGA register read/write protocols
> PATCH V2 -> V3:
> (1) fixed kernel test robot compiler warning.
> PATCH V1 -> V2:
> (1) Synchronizing upboard github to rc2.
> (2) Refer 2022/10/31 Lee Jones review, fixed some of the issues.
> ---
> drivers/mfd/Kconfig | 12 +
> drivers/mfd/Makefile | 1 +
> drivers/mfd/upboard-fpga.c | 492 +++++++++++++++++++++++++++++++
> include/linux/mfd/upboard-fpga.h | 55 ++++
> 4 files changed, 560 insertions(+)
> create mode 100644 drivers/mfd/upboard-fpga.c
> create mode 100644 include/linux/mfd/upboard-fpga.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index abb58ab1a1a4..1041e937fc7a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -2104,6 +2104,18 @@ config MFD_QCOM_PM8008
> under it in the device tree. Additional drivers must be enabled in
> order to use the functionality of the device.
>
> +config MFD_INTEL_UPBOARD_FPGA
> + tristate "Support for the Intel platform foundation kit UP board FPGA"
> + select MFD_CORE
> + depends on X86 && ACPI
> + help
> + Select this option to enable the Intel AAEON UP and UP^2 on-board FPGA.
> + This is core driver for the UP board that implements certain (pin
> + control, onboard LEDs or CEC) through an on-board FPGA.
> +
> + To compile this driver as a module, choose M here: the module will be
> + called upboard-fpga.
> +
> menu "Multimedia Capabilities Port drivers"
> depends on ARCH_SA1100
>
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 858cacf659d6..8374a05f6f43 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -250,6 +250,7 @@ obj-$(CONFIG_MFD_ALTERA_A10SR) += altera-a10sr.o
> obj-$(CONFIG_MFD_ALTERA_SYSMGR) += altera-sysmgr.o
> obj-$(CONFIG_MFD_STPMIC1) += stpmic1.o
> obj-$(CONFIG_MFD_SUN4I_GPADC) += sun4i-gpadc.o
> +obj-$(CONFIG_MFD_INTEL_UPBOARD_FPGA) += upboard-fpga.o
>
> obj-$(CONFIG_MFD_STM32_LPTIMER) += stm32-lptimer.o
> obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
> diff --git a/drivers/mfd/upboard-fpga.c b/drivers/mfd/upboard-fpga.c
> new file mode 100644
> index 000000000000..b5c36f9dbfdd
> --- /dev/null
> +++ b/drivers/mfd/upboard-fpga.c
> @@ -0,0 +1,492 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * UP Board for control CPLD/FPGA to
Nit: That's an odd place to break a line.
> + * provide more GPIO driving power also provide CPLD LEDs and pin mux function
> + * recognize HID AANT0F00 ~ AAANT0F04 in ACPI name space
> + *
> + * Copyright (c) AAEON. All rights reserved.
> + *
> + * Author: Gary Wang <garywang@xxxxxxxxxxxx>
> + *
Nit: Please remove this line.
> + */
> +
> +#include <linux/acpi.h>
> +#include <linux/dmi.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/kernel.h>
> +#include <linux/leds.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/upboard-fpga.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +
> +struct upboard_fpga_data {
> + const struct regmap_config *regmap_config;
> + const struct mfd_cell *cells;
> + size_t ncells;
> +};
> +
> +static struct gpio_led_platform_data pdata;
No globals if you can help it. Please *alloc this.
> +#define RESET_DEVICE 1
> +#define ENABLE_DEVICE 1
> +
> +#define AAEON_MANUFACTURER_ID 0x01
> +#define SUPPORTED_FW_MAJOR 0x0
> +#define MENUFACTURER_ID_MASK GENMASK(7, 0)
> +
> +#define FIRMWARE_ID_BUILD_OFFSET 12
> +#define FIRMWARE_ID_MAJOR_OFFSET 8
> +#define FIRMWARE_ID_MINOR_OFFSET 4
> +#define FIRMWARE_ID_PATCH_OFFSET 0
> +#define FIRMWARE_ID_MASK GENMASK(3, 0)
> +
> +/*
> + * read CPLD register on custom protocol
> + * send clock and addr bit in strobe and datain pins then read from dataout pin
> + */
> +static int upboard_fpga_read(void *context, unsigned int reg, unsigned int *val)
> +{
> + struct upboard_fpga * const fpga = context;
> + int i;
> +
> + /* clear to start new transcation */
> + gpiod_set_value(fpga->clear_gpio, 0);
> + gpiod_set_value(fpga->clear_gpio, 1);
> +
> + reg |= UPFPGA_READ_FLAG;
> +
> + /* send clock and data from strobe & datain */
> + for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
> + gpiod_set_value(fpga->strobe_gpio, 0);
> + gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
> + gpiod_set_value(fpga->strobe_gpio, 1);
> + }
> +
> + gpiod_set_value(fpga->strobe_gpio, 0);
> + *val = 0;
> +
> + /* read from dataout */
> + for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
> + gpiod_set_value(fpga->strobe_gpio, 1);
> + gpiod_set_value(fpga->strobe_gpio, 0);
> + *val |= gpiod_get_value(fpga->dataout_gpio) << i;
> + }
> +
> + gpiod_set_value(fpga->strobe_gpio, 1);
> +
> + return 0;
> +}
> +
> +/*
> + * write CPLD register on custom protocol
> + * send clock and addr bit in strobe and datain pins then write to datain pin
> + */
> +static int upboard_fpga_write(void *context, unsigned int reg, unsigned int val)
> +{
> + struct upboard_fpga * const fpga = context;
> + int i;
> +
> + /* clear to start new transcation */
> + gpiod_set_value(fpga->clear_gpio, 0);
> + gpiod_set_value(fpga->clear_gpio, 1);
> +
> + /* send clock and data from strobe & datain */
> + for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
> + gpiod_set_value(fpga->strobe_gpio, 0);
> + gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
> + gpiod_set_value(fpga->strobe_gpio, 1);
> + }
> +
> + gpiod_set_value(fpga->strobe_gpio, 0);
> +
> + /* write to datain pin */
> + for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
> + gpiod_set_value(fpga->datain_gpio, !!(val & BIT(i)));
> + gpiod_set_value(fpga->strobe_gpio, 1);
> + gpiod_set_value(fpga->strobe_gpio, 0);
> + }
> +
> + gpiod_set_value(fpga->strobe_gpio, 1);
> +
> + return 0;
> +}
Should this live in drivers/fpga?
> +static const struct regmap_range upboard_up_readable_ranges[] = {
> + regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
> + regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
> + regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
> +};
> +
> +static const struct regmap_range upboard_up_writable_ranges[] = {
> + regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
> + regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
> +};
> +
> +static const struct regmap_access_table upboard_up_readable_table = {
> + .yes_ranges = upboard_up_readable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(upboard_up_readable_ranges),
> +};
> +
> +static const struct regmap_access_table upboard_up_writable_table = {
> + .yes_ranges = upboard_up_writable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(upboard_up_writable_ranges),
> +};
> +
> +static const struct regmap_config upboard_up_regmap_config = {
> + .reg_bits = UPFPGA_ADDRESS_SIZE,
> + .val_bits = UPFPGA_REGISTER_SIZE,
> + .max_register = UPFPGA_REG_MAX,
> + .reg_read = upboard_fpga_read,
> + .reg_write = upboard_fpga_write,
> + .fast_io = false,
> + .cache_type = REGCACHE_NONE,
> + .rd_table = &upboard_up_readable_table,
> + .wr_table = &upboard_up_writable_table,
> +};
> +
> +/* 3 LEDs controlled by CPLD */
> +static struct upboard_led_data upboard_up_led_data[] = {
> + { .bit = 0, .colour = "yellow" },
> + { .bit = 1, .colour = "green" },
> + { .bit = 2, .colour = "red" },
> +};
> +
> +static const struct mfd_cell upboard_up_mfd_cells[] = {
> + MFD_CELL_NAME("upboard-pinctrl"),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[0],
> + sizeof(*upboard_up_led_data), 1),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[1],
> + sizeof(*upboard_up_led_data), 2),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[2],
> + sizeof(*upboard_up_led_data), 3),
What other devices does the upboard support?
I'm not sure that an LED device constitutes an MFD?
> +};
> +
> +/* UP Squared 6000 EHL board */
> +
> +static const struct upboard_fpga_data upboard_up_fpga_data = {
> + .regmap_config = &upboard_up_regmap_config,
> + .cells = upboard_up_mfd_cells,
> + .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
> +};
> +
> +static const struct mfd_cell upboard_pinctrl_cells[] = {
> + MFD_CELL_NAME("upboard-pinctrl"),
> +};
> +
> +static const struct upboard_fpga_data upboard_pinctrl_data = {
> + .regmap_config = &upboard_up_regmap_config,
> + .cells = upboard_pinctrl_cells,
> + .ncells = ARRAY_SIZE(upboard_pinctrl_cells),
> +};
> +
> +/* UP^2 board */
> +static const struct regmap_range upboard_up2_readable_ranges[] = {
> + regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
> + regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
> + regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
> + regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
> +};
> +
> +static const struct regmap_range upboard_up2_writable_ranges[] = {
> + regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
> + regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
> + regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
> +};
> +
> +static const struct regmap_access_table upboard_up2_readable_table = {
> + .yes_ranges = upboard_up2_readable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(upboard_up2_readable_ranges),
> +};
> +
> +static const struct regmap_access_table upboard_up2_writable_table = {
> + .yes_ranges = upboard_up2_writable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(upboard_up2_writable_ranges),
> +};
> +
> +static const struct regmap_config upboard_up2_regmap_config = {
> + .reg_bits = UPFPGA_ADDRESS_SIZE,
> + .val_bits = UPFPGA_REGISTER_SIZE,
> + .max_register = UPFPGA_REG_MAX,
> + .reg_read = upboard_fpga_read,
> + .reg_write = upboard_fpga_write,
> + .fast_io = false,
> + .cache_type = REGCACHE_NONE,
> + .rd_table = &upboard_up2_readable_table,
> + .wr_table = &upboard_up2_writable_table,
> +};
> +
> +static struct upboard_led_data upboard_up2_led_data[] = {
> + { .bit = 0, .colour = "blue" },
> + { .bit = 1, .colour = "yellow" },
> + { .bit = 2, .colour = "green" },
> + { .bit = 3, .colour = "red" },
> +};
> +
> +static const struct mfd_cell upboard_up2_mfd_cells[] = {
> + MFD_CELL_NAME("upboard-pinctrl"),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[0],
> + sizeof(*upboard_up2_led_data), 1),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[1],
> + sizeof(*upboard_up2_led_data), 2),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[2],
> + sizeof(*upboard_up2_led_data), 3),
> + MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[3],
> + sizeof(*upboard_up2_led_data), 4),
> +};
> +
> +static const struct upboard_fpga_data upboard_up2_fpga_data = {
> + .regmap_config = &upboard_up2_regmap_config,
> + .cells = upboard_up2_mfd_cells,
> + .ncells = ARRAY_SIZE(upboard_up2_mfd_cells),
> +};
> +
> +/* UP-CRST02 carrier board for UP Core */
> +
> +/* same MAX10 config as UP2, but same LED cells as UP1 */
> +static const struct upboard_fpga_data upboard_upcore_crst02_fpga_data = {
> + .regmap_config = &upboard_up2_regmap_config,
> + .cells = upboard_up_mfd_cells,
> + .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
> +};
> +
> +static int __init upboard_fpga_gpio_init(struct upboard_fpga *fpga)
> +{
> + enum gpiod_flags flags = fpga->uninitialised ? GPIOD_OUT_LOW : GPIOD_ASIS;
> +
> + fpga->enable_gpio = devm_gpiod_get(fpga->dev, "enable", flags);
> + if (IS_ERR(fpga->enable_gpio))
> + return PTR_ERR(fpga->enable_gpio);
> +
> + fpga->clear_gpio = devm_gpiod_get(fpga->dev, "clear", GPIOD_OUT_LOW);
> + if (IS_ERR(fpga->clear_gpio))
> + return PTR_ERR(fpga->clear_gpio);
> +
> + fpga->strobe_gpio = devm_gpiod_get(fpga->dev, "strobe", GPIOD_OUT_LOW);
> + if (IS_ERR(fpga->strobe_gpio))
> + return PTR_ERR(fpga->strobe_gpio);
> +
> + fpga->datain_gpio = devm_gpiod_get(fpga->dev, "datain", GPIOD_OUT_LOW);
> + if (IS_ERR(fpga->datain_gpio))
> + return PTR_ERR(fpga->datain_gpio);
> +
> + fpga->dataout_gpio = devm_gpiod_get(fpga->dev, "dataout", GPIOD_IN);
> + if (IS_ERR(fpga->dataout_gpio))
> + return PTR_ERR(fpga->dataout_gpio);
> +
> + /*
> + * The SoC pinctrl driver may not support reserving the GPIO line for
> + * FPGA reset without causing an undesired reset pulse. This will clear
> + * any settings on the FPGA, so only do it if we must.
> + * Reset GPIO defaults HIGH, get GPIO and set to LOW, then set back to
> + * HIGH as a pulse.
> + */
> + if (fpga->uninitialised) {
> + fpga->reset_gpio = devm_gpiod_get(fpga->dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(fpga->reset_gpio))
> + return PTR_ERR(fpga->reset_gpio);
> +
> + gpiod_set_value(fpga->reset_gpio, RESET_DEVICE);
> + }
> +
> + gpiod_set_value(fpga->enable_gpio, ENABLE_DEVICE);
> + fpga->uninitialised = false;
> +
> + return 0;
> +}
> +
> +static int __init upboard_fpga_verify_device(struct upboard_fpga *fpga)
> +{
> + unsigned int platform_id, manufacturer_id;
> + unsigned int firmware_id, build, major, minor, patch;
> + int ret;
> +
> + ret = regmap_read(fpga->regmap, UPFPGA_REG_PLATFORM_ID, &platform_id);
> + if (ret)
> + return ret;
> +
> + manufacturer_id = platform_id & MENUFACTURER_ID_MASK;
> + if (manufacturer_id != AAEON_MANUFACTURER_ID) {
> + dev_err(fpga->dev,
> + "Manufacturer ID 0x%02x not supported\n",
> + manufacturer_id);
> +
> + return -ENODEV;
> + }
> +
> + ret = regmap_read(fpga->regmap, UPFPGA_REG_FIRMWARE_ID, &firmware_id);
> + if (ret)
> + return ret;
> +
> + build = (firmware_id >> FIRMWARE_ID_BUILD_OFFSET) & FIRMWARE_ID_MASK;
> + major = (firmware_id >> FIRMWARE_ID_MAJOR_OFFSET) & FIRMWARE_ID_MASK;
> + minor = (firmware_id >> FIRMWARE_ID_MINOR_OFFSET) & FIRMWARE_ID_MASK;
> + patch = (firmware_id >> FIRMWARE_ID_PATCH_OFFSET) & FIRMWARE_ID_MASK;
> +
> + if (major != SUPPORTED_FW_MAJOR) {
> + dev_err(fpga->dev, "Manufacturer ID 0x%02x not supported\n", build);
> +
> + return -ENODEV;
> + }
> +
> + dev_info(fpga->dev, "Compatible FPGA FW v%u.%u.%u build 0x%02x",
> + major, minor, patch, build);
> +
> + return 0;
> +}
> +
> +static const struct mfd_cell upboard_gpio_led_cells[] = {
> + MFD_CELL_BASIC("leds-gpio", NULL,
> + &pdata,
> + sizeof(pdata), 0)
> +};
> +
> +static int upboard_led_gpio_register(struct upboard_fpga *fpga)
> +{
> + struct gpio_led blue_led, yellow_led, green_led, red_led;
> + struct gpio_desc *desc;
> + static struct gpio_led leds[4];
> + int num_leds = 0;
> + int ret;
> +
> + desc = devm_gpiod_get(fpga->dev, "blue", GPIOD_OUT_LOW);
> + if (!IS_ERR(desc)) {
> + blue_led.name = "upboard:blue:";
> + blue_led.gpio = desc_to_gpio(desc);
> + blue_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
> + leds[num_leds++] = blue_led;
> + devm_gpiod_put(fpga->dev, desc);
> + }
> +
> + desc = devm_gpiod_get(fpga->dev, "yellow", GPIOD_OUT_LOW);
> + if (!IS_ERR(desc)) {
> + yellow_led.name = "upboard:yellow:";
> + yellow_led.gpio = desc_to_gpio(desc);
> + yellow_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
> + leds[num_leds++] = yellow_led;
> + devm_gpiod_put(fpga->dev, desc);
> + }
> +
> + desc = devm_gpiod_get(fpga->dev, "green", GPIOD_OUT_LOW);
> + if (!IS_ERR(desc)) {
> + green_led.name = "upboard:green:";
> + green_led.gpio = desc_to_gpio(desc);
> + green_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
> + leds[num_leds++] = green_led;
> + devm_gpiod_put(fpga->dev, desc);
> + }
> +
> + desc = devm_gpiod_get(fpga->dev, "red", GPIOD_OUT_LOW);
> + if (!IS_ERR(desc)) {
> + red_led.name = "upboard:red:";
> + red_led.gpio = desc_to_gpio(desc);
> + red_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
> + leds[num_leds++] = red_led;
> + devm_gpiod_put(fpga->dev, desc);
> + }
> +
> + /* No optional LEDs defined */
> + if (num_leds == 0)
> + return 0;
> +
> + pdata.num_leds = num_leds;
> + pdata.leds = leds;
Where is this consumed?
If the answer is "only the LED"driver, then move it there.
> + ret = devm_mfd_add_devices(fpga->dev, PLATFORM_DEVID_AUTO,
> + upboard_gpio_led_cells,
> + ARRAY_SIZE(upboard_gpio_led_cells),
> + NULL, 0, NULL);
> + if (ret) {
> + dev_err(fpga->dev, "Failed to add GPIO LEDs, %d", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * -------------------------------------- ------------
> + * | Intel SOC,1.8V | --- |ADC Chip | native driver
> + * | GPIO/I2C/SPI/UART/PWM | |SPI/I2C |
> + * -------------------------------------- -------------
> + * | |
> + * ----------------------------------------------------------
> + * | CPLD/FPGA Driver | upboard-fpga CPLD control driver
> + * | provide more GPIO driving power | register leds-upboard
> + * | HAT 40 pin mux function | register pinctrl-upboard
> + * ---------------------------------------------------------
> + * | |
> + * ---------- -------------------------------------------
> + * |3 or 4| | HAT 40 pins, 3.3V | leds-upboard
> + * | Leds | |GPIO/ADC/I2C/SPI/UART/PWM | pinctrl-upboard
> + * ---------- -------------------------------------------
> + */
> +static const struct acpi_device_id upboard_fpga_acpi_match[] = {
> + { "AANT0000", (kernel_ulong_t)&upboard_pinctrl_data },
> + { "AANT0F00", (kernel_ulong_t)&upboard_up_fpga_data },
> + { "AANT0F01", (kernel_ulong_t)&upboard_up2_fpga_data },
> + { "AANT0F02", (kernel_ulong_t)&upboard_up_fpga_data },
> + { "AANT0F03", (kernel_ulong_t)&upboard_upcore_crst02_fpga_data },
> + { "AANT0F04", (kernel_ulong_t)&upboard_up_fpga_data },
When I asked you not to place MFD data through other platform APIs, I
didn't mean continue to pass it through hidden inside another structure.
I meant don't pass it through at all. Please use differentiating IDs
(usually just an numerical value), then match on those (usually in a
switch-case). There are lots of examples of people doing this.
> + { }
> +};
> +MODULE_DEVICE_TABLE(acpi, upboard_fpga_acpi_match);
> +
> +static int __init upboard_fpga_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct upboard_fpga *ddata;
> + const struct acpi_device_id *id;
> + const struct upboard_fpga_data *fpga_data;
> + int ret;
> +
> + id = acpi_match_device(upboard_fpga_acpi_match, dev);
> + if (!id)
> + return -ENODEV;
> +
> + fpga_data = (const struct upboard_fpga_data *) id->driver_data;
> +
> + ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
> + if (!ddata)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, ddata);
> + ddata->dev = dev;
> +
> + ddata->regmap = devm_regmap_init(dev, NULL, ddata, fpga_data->regmap_config);
> + if (IS_ERR(ddata->regmap))
> + return PTR_ERR(ddata->regmap);
> +
> + ddata->regmap_config = fpga_data->regmap_config;
> +
> + ret = upboard_fpga_gpio_init(ddata);
> + if (ret) {
> + /* Not FPGA firmware, abort FPGA GPIO initialize process */
> + dev_warn(dev, "Failed to initialize FPGA common GPIOs: %d", ret);
> + } else {
> + upboard_fpga_verify_device(ddata);
> + }
> +
> + ret = upboard_led_gpio_register(ddata);
> + if (ret) {
> + /* LEDs are optional. */
> + dev_warn(dev, "Failed to register LEDs: %d", ret);
> + }
If LEDs are optional, what does this device do?
LEDs are the only functional piece of this that I can see.
> + return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO,
> + fpga_data->cells,
> + fpga_data->ncells,
> + NULL, 0, NULL);
> +}
> +
> +static struct platform_driver upboard_fpga_driver = {
> + .driver = {
> + .name = "upboard-fpga",
> + .acpi_match_table = upboard_fpga_acpi_match,
> + },
> +};
> +module_platform_driver_probe(upboard_fpga_driver, upboard_fpga_probe);
> +
> +MODULE_AUTHOR("Gary Wang <garywang@xxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("UP Board CPLD/FPGA driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/upboard-fpga.h b/include/linux/mfd/upboard-fpga.h
> new file mode 100644
> index 000000000000..d6bf7dd11da8
> --- /dev/null
> +++ b/include/linux/mfd/upboard-fpga.h
> @@ -0,0 +1,55 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * UP Board CPLD/FPGA driver
> + *
> + * Copyright (c) AAEON. All rights reserved.
> + *
> + * Author: Gary Wang <garywang@xxxxxxxxxxxx>
> + *
Nit: Remove this line.
> + */
> +
> +#ifndef __MFD_UPBOARD_FPGA_H
> +#define __MFD_UPBOARD_FPGA_H
> +
> +/* CPLD/FPGA protocol version */
> +#define UPFPGA_PROTOCOL_V1_HRV 1
> +#define UPFPGA_PROTOCOL_V2_HRV 2
> +
> +#define UPFPGA_ADDRESS_SIZE 7
> +#define UPFPGA_REGISTER_SIZE 16
> +
> +#define UPFPGA_READ_FLAG BIT(UPFPGA_ADDRESS_SIZE)
> +
> +enum upboard_fpgareg {
> + UPFPGA_REG_PLATFORM_ID = 0x10,
> + UPFPGA_REG_FIRMWARE_ID = 0x11,
> + UPFPGA_REG_FUNC_EN0 = 0x20,
> + UPFPGA_REG_FUNC_EN1 = 0x21,
> + UPFPGA_REG_GPIO_EN0 = 0x30,
> + UPFPGA_REG_GPIO_EN1 = 0x31,
> + UPFPGA_REG_GPIO_EN2 = 0x32,
> + UPFPGA_REG_GPIO_DIR0 = 0x40,
> + UPFPGA_REG_GPIO_DIR1 = 0x41,
> + UPFPGA_REG_GPIO_DIR2 = 0x42,
> + UPFPGA_REG_MAX,
> +};
> +
> +struct upboard_fpga {
> + struct device *dev;
> + struct regmap *regmap;
> + const struct regmap_config *regmap_config;
Where is this consumed?
> + struct gpio_desc *enable_gpio;
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *clear_gpio;
> + struct gpio_desc *strobe_gpio;
> + struct gpio_desc *datain_gpio;
> + struct gpio_desc *dataout_gpio;
> + bool uninitialised;
> +};
> +
> +struct upboard_led_data {
> + unsigned int bit;
> + const char *colour;
> +};
> +
> +#endif /* __MFD_UPBOARD_FPGA_H */
> --
> 2.17.1
>
--
Lee Jones [李琼斯]