Re: [PATCH 2/2] net: dsa: microchip: Provide Module 4 KSZ9477 errata (DS80000754C)

[Lukasz Majewski]

Hi Vladimir,

> Hi Lukasz,
> 
> On Tue, Aug 29, 2023 at 10:35:33AM +0200, Lukasz Majewski wrote:
> > Hi Vladimir,
> >   
> > > On Fri, Aug 25, 2023 at 06:48:41PM +0000,
> > > Tristram.Ha@xxxxxxxxxxxxx wrote:  
> > > > > > IMHO adding functions to MMD modification would facilitate
> > > > > > further development (for example LED setup).    
> > > > > 
> > > > > We already have some KSZ9477 specific initialization done in
> > > > > the Micrel PHY driver under drivers/net/phy/micrel.c, can we
> > > > > converge on the PHY driver which has a reasonable amount of
> > > > > infrastructure for dealing with workarounds, indirect or
> > > > > direct MMD accesses etc.?    
> > > > 
> > > > Actually the internal PHY used in the KSZ9897/KSZ9477/KSZ9893
> > > > switches are special and only used inside those switches.
> > > > Putting all the switch related code in Micrel PHY driver does
> > > > not really help.  When the switch is reset all those PHY
> > > > registers need to be set again, but the PHY driver only
> > > > executes those code during PHY initialization.  I do not know
> > > > if there is a good way to tell the PHY to re-initialize again.
> > > >   
> > > 
> > > Suppose there was a method to tell the PHY driver to re-initialize
> > > itself. What would be the key points in which the DSA switch
> > > driver would need to trigger that method? Where is the switch
> > > reset at runtime?  
> > 
> > Tristam has explained why adding the internal switch PHY errata to
> > generic PHY code is not optimal.  
> 
> Yes, and I didn't understand that explanation, so I asked a
> clarification question.

Ok. Let's wait for Tristram's answer.

> 
> > If adding MMD generic code is a problem - then I'm fine with just
> > clearing proper bits with just two indirect writes in the
> > drivers/net/dsa/microchip/ksz9477.c
> > 
> > I would also prefer to keep the separate ksz9477_errata() function,
> > so we could add other errata code there.
> > 
> > Just informative - without this patch the KSZ9477-EVB board's
> > network is useless when the other peer has EEE enabled by default
> > (like almost all non managed ETH switches).  
> 
> No, adding direct PHY MMD access code to the ksz9477 switch driver is
> not even the biggest problem - even though, IIUC, the "workaround" to
> disable EEE advertisement could be moved to ksz9477_get_features() in
> drivers/net/phy/micrel.c, where phydev->supported_eee could be
> cleared.

To be even more interesting (after looking into the PHY micrel.c code):
https://elixir.bootlin.com/linux/latest/source/drivers/net/phy/micrel.c#L1804

The errata from this patch is already present.

The issue is that ksz9477_config_init() (drivers/net/phy/micrel.c) is
executed AFTER generic phy_probe():
https://elixir.bootlin.com/linux/latest/source/drivers/net/phy/phy_device.c#L3256
in which the EEE advertisement registers are read.

Hence, those registers needs to be cleared earlier - as I do in
ksz9477_setup() in drivers/net/dsa/microchip/ksz9477.

Here the precedence matters ...

> 
> The biggest problem that I see is that Oleksij Rempel has "just" added
> EEE support to the KSZ9477 earlier this year, with an ack from Arun
> Ramadoss: 69d3b36ca045 ("net: dsa: microchip: enable EEE support").
> I'm not understanding why the erratum wasn't a discussion topic then.

+1

> 
> I am currently on vacation and won't be able to look very deeply into
> the problem, but IIUC, your patch undoes that work, and so, it needs
> an ACK from Oleksij.

Ok.


Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@xxxxxxx

Attachment: pgpxL3VC0R1rH.pgp
Description: OpenPGP digital signature