Re: [patch 41/58] x86/apic: Add max_apic_id member

[Thomas Gleixner]

On Tue, Jul 18 2023 at 09:47, Thomas Gleixner wrote:
> On Mon, Jul 17 2023 at 17:19, Linus Torvalds wrote:
>> So all of your patches make sense to me, but the whole apic_flat case
>> confuses me.
>>
>> On Mon, 17 Jul 2023 at 16:15, Thomas Gleixner <tglx@xxxxxxxxxxxxx> wrote:
>>>
>>> --- a/arch/x86/kernel/apic/apic_flat_64.c
>>> +++ b/arch/x86/kernel/apic/apic_flat_64.c
>>> @@ -94,6 +94,7 @@ static struct apic apic_flat __ro_after_
>>>         .cpu_present_to_apicid          = default_cpu_present_to_apicid,
>>>         .phys_pkg_id                    = flat_phys_pkg_id,
>>>
>>> +       .max_apic_id                    = 0xFE,
>>>         .get_apic_id                    = flat_get_apic_id,
>>>         .set_apic_id                    = set_apic_id,
>>
>> flat_send_IPI_mask() can only deal with a single word mask. How the
>> heck can the max apic ID be more than 64?
>>
>> I'm probably very confused.
>
> APIC is doing that to people.
>
> The confusing part here is the physical APIC ID vs. the destination
> mode.
>
> Physical APIC ID is always a unique number per CPU (APIC) and on XAPIC
> ranging from 0x0 to 0xFE. That's what is actually checked with that
> max_apic_id entry.
>
> Destination mode is a different story. APIC has two destination modes
> for actually sending IPIs or messages from IO/APIC or PCI/MSI: Physical
> and logical.
>
> Logical is a bitmap of 8 bits, where each bit represents one CPU. So the
> maximum number of CPUs addressable in logical mode is 8.
>
> You can have a system with 8 CPUs where the physical APIC IDs are
> 0x20-0x27 and use logical destination mode by setting the LDR register
> to the bit which represents the CPU, i.e. 1 << CPU#.
>
> So in that 8 CPU case LDR is 0x1, 0x2, ... 0x80 on CPU0 - 7. When
> sending an IPI then the destination mode in the ICR is set to logical
> and the destination field is written with the bit representing the
> target, i.e. 1 << CPU#. The destination field can have multiple bits set
> to send the IPI to several CPUs (up to 8) with a single ICR write
> operation.
>
> Once the machine has more than 8 CPUs we are forced to use physical
> destination mode. Physical destination mode is using the physical APIC
> ID of the target: 0-254 are the valid addresses, which fit into one
> byte. 255 (0xff) is a broadcast address. Sending IPIs to multiple
> targets needs one ICR write per target, which is obviously more
> expensive as between each write the ICR register has to be read back and
> the ICR busy bit needs to go back to zero before the next ICR write can
> happen.
>
> X2APIC is similar. It just has a wider physical APIC ID space (full
> 32bit). X2APIC has a logical destination mode too which is more
> useful. The logical destination is 32bit wide and split into two areas:
>
>   [cluster ID] [logical ID]
>
> Each being 16 bit wide. The logical ID is again one bit per CPU, the
> cluster ID is a number. So we can send IPIs to multiple targets (up to
> 16) within a cluster with one ICR write. If the IPI targets are in
> different clusters then obviously we need one write per cluster.
>
> Physical destination mode on X2APIC is the same as with XAPIC but
> cheaper as it does not need the ICR readback.

Just for making the confusion complete. XAPIC has a clustered logical
mode too:

The cluster ID is in the topmost 4 bits with a range from 0-14 and the
logical ID bits are the lower 4 bits. That means it works up to 4 * 15 =
60 CPUs.

The kernel never implemented that mode and with anything modern having
X2APIC I don't think it's worth the trouble to do so.

Thanks,

        tglx

---
"Confusion now hath made his masterpiece." - Shakespeare, Macbeth