Re: [PATCH v3 8/8] ARM: dts: stm32: Add Octavo OSD32MP1-RED board

[Sean Nyekjaer]

> On 12 Jul 2023, at 10.34, Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> wrote:
> 
> On 12/07/2023 08:29, Sean Nyekjaer wrote:
>> Add support for the Octavo OSD32MP1-RED development board.
>> 
>> General features:
>> - STM32MP157C
>> - 512MB DDR3
>> - CAN-FD
>> - HDMI
>> - USB-C OTG
>> - UART
>> 
> 
> ...
> 
>> +
>> +&i2c1 {
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&i2c1_pins_a>;
>> + pinctrl-1 = <&i2c1_sleep_pins_a>;
>> + status = "okay";
>> + i2c-scl-rising-time-ns = <100>;
>> + i2c-scl-falling-time-ns = <7>;
>> + /delete-property/dmas;
>> + /delete-property/dma-names;
> 
> You should explain it with comment, unless it is quite common for all
> STM32 boards to disable DMA for I2C...

Quite common for all STM32 boards, but I will add a comment anyway :)

> 
>> +
>> + hdmi-transmitter@39 {
>> + compatible = "sil,sii9022";
>> + reg = <0x39>;
>> + reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
>> + interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
>> + interrupt-parent = <&gpiog>;
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&ltdc_pins_e>;
>> + pinctrl-1 = <&ltdc_sleep_pins_e>;
>> + status = "okay";
> 
> Did anything disable this node?

No will remove.

> 
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + sii9022_in: endpoint {
>> + remote-endpoint = <&ltdc_ep0_out>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + sii9022_tx_endpoint: endpoint {
>> + remote-endpoint = <&i2s2_endpoint>;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2s2 {
>> + clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc CK_PER>, <&rcc PLL3_R>;
>> + clock-names = "pclk", "i2sclk", "x8k", "x11k";
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&i2s2_pins_b>;
>> + pinctrl-1 = <&i2s2_sleep_pins_b>;
>> + status = "okay";
>> +
>> + i2s2_port: port {
>> + i2s2_endpoint: endpoint {
>> + remote-endpoint = <&sii9022_tx_endpoint>;
>> + format = "i2s";
>> + mclk-fs = <256>;
>> + };
>> + };
>> +};
>> +
>> +&ltdc {
>> + status = "okay";
>> +
>> + port {
>> + ltdc_ep0_out: endpoint@0 {
>> + reg = <0>;
>> + remote-endpoint = <&sii9022_in>;
>> + };
>> + };
>> +};
>> +
>> +&m_can1 {
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&m_can1_pins_d>;
>> + pinctrl-1 = <&m_can1_sleep_pins_d>;
>> + status = "okay";
>> +};
>> +
>> +&pwr_regulators {
>> + vdd-supply = <&vdd>;
>> + vdd_3v3_usbfs-supply = <&vdd_usb>;
>> +};
>> +
>> +&rtc {
>> + status = "okay";
>> +};
>> +
>> +&sdmmc1 {
>> + pinctrl-names = "default", "opendrain", "sleep";
>> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
>> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>> + cd-gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>> + disable-wp;
>> + st,neg-edge;
>> + bus-width = <4>;
>> + vmmc-supply = <&v3v3>;
>> + status = "okay";
>> +};
>> +
>> +&sdmmc2 {
>> + pinctrl-names = "default", "opendrain", "sleep";
>> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
>> + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
>> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
>> + non-removable;
>> + no-sd;
>> + no-sdio;
>> + st,neg-edge;
>> + bus-width = <8>;
>> + vmmc-supply = <&v3v3>;
>> + vqmmc-supply = <&vdd>;
>> + mmc-ddr-3_3v;
>> + status = "okay";
>> +};
>> +
>> +&uart4 {
>> + pinctrl-names = "default", "sleep", "idle";
>> + pinctrl-0 = <&uart4_pins_a>;
>> + pinctrl-1 = <&uart4_sleep_pins_a>;
>> + pinctrl-2 = <&uart4_idle_pins_a>;
>> + /delete-property/dmas;
>> + /delete-property/dma-names;
> 
> Same concerns.

Thanks for the review Krzysztof.

/Sean

> 
> Best regards,
> Krzysztof
>