[PATCH v1 08/13] arm64: dts: rockchip: rock-5a: add analog audio

[Sebastian Reichel]

Add analog audio support based on the Everest Semi ES8316 codec.

Note, that this currently does not support headphone plug events. The
Rock 5A uses a different headphone jack with a different logic to detect
a headphone plug. Unfortunately the detect GPIO is always low.
Downstream uses an ADC channel instead, but that is currently not
supported upstream.

Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxx>
---
 .../boot/dts/rockchip/rk3588s-rock-5a.dts     | 52 +++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
index 5bad81c5b09d..4c6c87d462e9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
@@ -16,6 +16,20 @@ aliases {
 		serial2 = &uart2;
 	};
 
+	analog-sound {
+		compatible = "audio-graph-card";
+		label = "rk3588-es8316";
+
+		widgets = "Microphone", "Mic Jack",
+			  "Headphone", "Headphones";
+
+		routing = "MIC2", "Mic Jack",
+			  "Headphones", "HPOL",
+			  "Headphones", "HPOR";
+
+		dais = <&i2s0_8ch_p0>;
+	};
+
 	chosen {
 		stdout-path = "serial2:1500000n8";
 	};
@@ -149,6 +163,44 @@ regulator-state-mem {
 	};
 };
 
+&i2c7 {
+	status = "okay";
+
+	es8316: audio-codec@11 {
+		compatible = "everest,es8316";
+		reg = <0x11>;
+		clocks = <&cru I2S0_8CH_MCLKOUT>;
+		clock-names = "mclk";
+		assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+		assigned-clock-rates = <12288000>;
+		#sound-dai-cells = <0>;
+
+		port {
+			es8316_p0_0: endpoint {
+				remote-endpoint = <&i2s0_8ch_p0_0>;
+			};
+		};
+	};
+};
+
+&i2s0_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_lrck
+		     &i2s0_mclk
+		     &i2s0_sclk
+		     &i2s0_sdi0
+		     &i2s0_sdo0>;
+	status = "okay";
+
+	i2s0_8ch_p0: port {
+		i2s0_8ch_p0_0: endpoint {
+			dai-format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&es8316_p0_0>;
+		};
+	};
+};
+
 &gmac1 {
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
-- 
2.40.1