[PATCH 1/2] net: phy: mscc: add support for CLKOUT ctrl reg for VSC8531 and similar

[Alexandru Ardelean]

The VSC8531 and similar PHYs (i.e. VSC8530, VSC8531, VSC8540 & VSC8541)
have a CLKOUT pin on the chip that can be controlled by register (13G in
the General Purpose Registers page) that can be configured to output a
frequency of 25, 50 or 125 Mhz.

This is useful when wanting to provide a clock source for the MAC in some
board designs.

Signed-off-by: Marius Muresan <marius.muresan@xxxxxx>
Signed-off-by: Alexandru Ardelean <alex@xxxxxxxxxxx>
---

The original patch was done by Marius.
The final (upstream) version was done by Alex.

Tested on VSC8531.

 drivers/net/phy/mscc/mscc.h      |  5 ++++
 drivers/net/phy/mscc/mscc_main.c | 40 ++++++++++++++++++++++++++++++++
 2 files changed, 45 insertions(+)

diff --git a/drivers/net/phy/mscc/mscc.h b/drivers/net/phy/mscc/mscc.h
index 7a962050a4d4..4ea21921a7ba 100644
--- a/drivers/net/phy/mscc/mscc.h
+++ b/drivers/net/phy/mscc/mscc.h
@@ -181,6 +181,11 @@ enum rgmii_clock_delay {
 #define VSC8502_RGMII_TX_DELAY_MASK	  0x0007
 #define VSC8502_RGMII_RX_CLK_DISABLE	  0x0800
 
+/* CKLOUT Control register, for VSC8531 and similar */
+#define VSC8531_CLKOUT_CNTL		  13
+#define VSC8531_CLKOUT_CNTL_ENABLE	  BIT(15)
+#define VSC8531_CLKOUT_CNTL_FREQ_MASK	  GENMASK(14, 13)
+
 #define MSCC_PHY_WOL_LOWER_MAC_ADDR	  21
 #define MSCC_PHY_WOL_MID_MAC_ADDR	  22
 #define MSCC_PHY_WOL_UPPER_MAC_ADDR	  23
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 4171f01d34e5..61c1554935ce 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -618,6 +618,41 @@ static void vsc85xx_tr_write(struct phy_device *phydev, u16 addr, u32 val)
 	__phy_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
 }
 
+static int vsc8531_clkout_config(struct phy_device *phydev)
+{
+	static const u32 freq_vals[] = { 25, 50, 125 };
+	struct device *dev = &phydev->mdio.dev;
+	u16 mask, set;
+	u32 freq, i;
+	int rc;
+
+	mask = VSC8531_CLKOUT_CNTL_ENABLE | VSC8531_CLKOUT_CNTL_FREQ_MASK;
+	set = 0;
+
+	if (device_property_read_u32(dev, "vsc8531,clkout-freq-mhz", &freq) == 0) {
+		/* The indices from 'freq_vals' are used in the register */
+		for (i = 0; i < ARRAY_SIZE(freq_vals); i++) {
+			if (freq != freq_vals[i])
+				continue;
+
+			set |= VSC8531_CLKOUT_CNTL_ENABLE |
+			       FIELD_PREP(VSC8531_CLKOUT_CNTL_FREQ_MASK, i);
+			break;
+		}
+		if (set == 0)
+			dev_warn(dev,
+				 "Invalid 'vsc8531,clkout-freq-mhz' value %u\n",
+				 freq);
+	}
+
+	mutex_lock(&phydev->lock);
+	rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_GPIO,
+			      VSC8531_CLKOUT_CNTL, mask, set);
+	mutex_unlock(&phydev->lock);
+
+	return rc;
+}
+
 static int vsc8531_pre_init_seq_set(struct phy_device *phydev)
 {
 	int rc;
@@ -1852,6 +1887,11 @@ static int vsc85xx_config_init(struct phy_device *phydev)
 		rc = vsc8531_pre_init_seq_set(phydev);
 		if (rc)
 			return rc;
+
+		rc = vsc8531_clkout_config(phydev);
+		if (rc)
+			return rc;
+
 	}
 
 	rc = vsc85xx_eee_init_seq_set(phydev);
-- 
2.40.1