Re: [EXTERNAL] Re: [PATCH] PCI: j721e: Fix delay before PERST# deassert
From: Verma, Achal
Date: Tue Jul 04 2023 - 12:07:17 EST
On 7/3/2023 9:51 PM, Bjorn Helgaas wrote:
In subject, "Fix" doesn't convey much information. Does it increase?
Decrease? How much time are we talking about? PERST# deassert is at
one end of the delay; what event is at the other end?
Hi Bjorn,
How about "Increase delay to 100ms for PERST# deassert from moment
power-rails achieve operating limits"
Some of these useful bits of information could appear in the subject
line.
On Mon, Jul 03, 2023 at 04:59:14PM +0530, Achal Verma wrote:
As per the PCIe Card Electromechanical specification REV. 3.0, PERST#
I think the current rev of this spec is r5.0. Can you cite that
instead? I think the relevant section is r5.0, sec 2.9.2.
REV 5.0 also quote same TPVPERL=100ms delay.
I refer REV. 3.0 as pci-j721e controller follows REV. 3.0
signal should be de-asserted after minimum 100ms from the time power-rails
become stable. Current delay of 100us is observed to be not enough on some
custom platform implemented using TI's K3 SOCs.
Is this delay for the benefit of the Root Port or for the attached
Endpoint? If the latter, my guess is that some Endpoints might
tolerate the current shorter delay, while others might require more,
and it doesn't sound like "TI's K3 SoC" would be relevant here.
Its for the endpoints, TI's EVB doesn't exhibit any issues with 100us
delay but some customer reported the issue with shorter delay.
I have been working to refactor this driver to build as a module, I too
observed the issue on re-probe after remove when delay is lesser.
So, to ensure 100ms delay to give sufficient time for power-rails and
refclk to become stable, change delay from 100us to 100ms.
From PCIe Card Electromechanical specification REV. 3.0 section 2.6.2:
TPVPERL: Power stable to PERST# inactive - 100ms
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
Numbers like 100ms that come from the PCIe specs should have #defines
for them. If we don't have one already, can you add one, please?
Sure, will do it in next revision but should this go in some generic PCI
header file or just pci-j721e.c
Fixes: f3e25911a430 ("PCI: j721e: Add TI J721E PCIe driver")
Signed-off-by: Achal Verma <a-verma1@xxxxxx>
---
drivers/pci/controller/cadence/pci-j721e.c | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/drivers/pci/controller/cadence/pci-j721e.c b/drivers/pci/controller/cadence/pci-j721e.c
index e70213c9060a..fa2b4c11d2c4 100644
--- a/drivers/pci/controller/cadence/pci-j721e.c
+++ b/drivers/pci/controller/cadence/pci-j721e.c
@@ -499,13 +499,12 @@ static int j721e_pcie_probe(struct platform_device *pdev)
/*
* "Power Sequencing and Reset Signal Timings" table in
* PCI EXPRESS CARD ELECTROMECHANICAL SPECIFICATION, REV. 3.0
- * indicates PERST# should be deasserted after minimum of 100us
- * once REFCLK is stable. The REFCLK to the connector in RC
- * mode is selected while enabling the PHY. So deassert PERST#
- * after 100 us.
+ * indicates PERST# should be deasserted after minimum of 100ms
+ * after power rails achieve specified operating limits and
+ * within this period reference clock should also become stable.
*/
if (gpiod) {
- usleep_range(100, 200);
+ msleep(100);
gpiod_set_value_cansleep(gpiod, 1);
}
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel