Re: [PATCH 6/6] arm64: dts: meson-t7-a311d2-khadas-vim4: add initial device-tree

From: Lucas Tanure
Date: Sun Jun 18 2023 - 13:42:08 EST

Next message: Lucas Tanure: "Re: [PATCH 3/6] clk: meson: t7: add peripheral clock controller"
Previous message: Lucas Tanure: "Re: [PATCH 5/6] tty: serial: meson: Added T7 SOC compatibility"
Next in thread: Lucas Tanure: "Re: [PATCH 6/6] arm64: dts: meson-t7-a311d2-khadas-vim4: add initial device-tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Fri, Jun 16, 2023 at 1:01 AM Yixun Lan <dlan@xxxxxxxxxx> wrote:
>
> Hi Lucas:
>
> On 19:29 Thu 15 Jun , Lucas Tanure wrote:
> > The Khadas VIM4 uses the Amlogic A311D2 SoC, based on the Amlogic T7 SoC
> > family, on a board with the same form factor as the VIM3 models.
> I'd like to see little bit more verbose messages here, like
> which functionality/driver added here - cpu, gic, timer, uart?
Ok, I add this information in the next version.
Its adding CPU, GIC, and UART.

>
> so, it's capable of booting into a serial console?
yes

>
> >
> > - 8GB LPDDR4X 2016MHz
> > - 32GB eMMC 5.1 storage
> > - 32MB SPI flash
> > - 10/100/1000 Base-T Ethernet
> > - AP6275S Wireless (802.11 a/b/g/n/ac/ax, BT5.1)
> > - HDMI 2.1 video
> > - HDMI Input
> > - 1x USB 2.0 + 1x USB 3.0 ports
> > - 1x USB-C (power) with USB 2.0 OTG
> > - 3x LED's (1x red, 1x blue, 1x white)
> > - 3x buttons (power, function, reset)
> > - M2 socket with PCIe, USB, ADC & I2C
> > - 40pin GPIO Header
> > - 1x micro SD card slot
> >
> > Signed-off-by: Lucas Tanure <tanure@xxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/amlogic/Makefile | 1 +
> > .../amlogic/meson-t7-a311d2-khadas-vim4.dts | 112 ++++++++++
> > arch/arm64/boot/dts/amlogic/meson-t7.dtsi | 202 ++++++++++++++++++
> > 3 files changed, 315 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > create mode 100644 arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> > index cd1c5b04890a..1c5846bd1ca0 100644
> > --- a/arch/arm64/boot/dts/amlogic/Makefile
> > +++ b/arch/arm64/boot/dts/amlogic/Makefile
> > @@ -74,3 +74,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb
> > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
> > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air-gbit.dtb
> > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air.dtb
> > +dtb-$(CONFIG_ARCH_MESON) += meson-t7-a311d2-khadas-vim4.dtb
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts b/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > new file mode 100644
> > index 000000000000..46e175536edf
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > @@ -0,0 +1,112 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2022 Wesion, Inc. All rights reserved.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "meson-t7.dtsi"
> > +
> > +/ {
> > + model = "Khadas VIM4";
> > +
> > + aliases {
> > + serial0 = &uart_A;
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + /* 3 MiB reserved for ARM Trusted Firmware (BL31) */
> > + secmon_reserved: secmon@5000000 {
> > + reg = <0x0 0x05000000 0x0 0x300000>;
> > + no-map;
> > + };
> > +
> > + /* 32 MiB reserved for ARM Trusted Firmware (BL32) */
> > + secmon_reserved_bl32: secmon@5300000 {
> > + reg = <0x0 0x05300000 0x0 0x2000000>;
> > + no-map;
> > + };
> > + };
> > +
> > + xtal: xtal-clk {
> > + compatible = "fixed-clock";
> > + clock-frequency = <24000000>;
> > + clock-output-names = "xtal";
> > + #clock-cells = <0>;
> > + };
> > +
> > + vddcpu_a: regulator-vddcpu-a {
> > + /*
> > + * MP8756GD Regulator.
> > + */
> > + compatible = "pwm-regulator";
> > +
> > + regulator-name = "VDDCPU_A";
> > + regulator-min-microvolt = <689000>;
> > + regulator-max-microvolt = <1049000>;
> > +
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vddcpu_b: regulator-vddcpu-a {
> > + /*
> > + * MP8756GD Regulator.
> > + */
> > + compatible = "pwm-regulator";
> > +
> > + regulator-name = "VDDCPU_B";
> > + regulator-min-microvolt = <689000>;
> > + regulator-max-microvolt = <1049000>;
> > +
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +};
> > +
> > +&clkc{
> > + clocks = <&xtal>;
> > + clock-names = "xtal";
> > + status = "okay";
> > +};
> > +
> > +&uart_A {
> > + status = "okay";
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&vddcpu_a>;
> > +};
> > +
> > +&cpu1 {
> > + cpu-supply = <&vddcpu_a>;
> > +};
> > +
> > +&cpu2 {
> > + cpu-supply = <&vddcpu_a>;
> > +};
> > +
> > +&cpu3 {
> > + cpu-supply = <&vddcpu_a>;
> > +};
> > +
> > +&cpu100 {
> > + cpu-supply = <&vddcpu_b>;
> > +};
> > +
> > +&cpu101 {
> > + cpu-supply = <&vddcpu_b>;
> > +};
> > +
> > +&cpu102 {
> > + cpu-supply = <&vddcpu_b>;
> > +};
> > +
> > +&cpu103 {
> > + cpu-supply = <&vddcpu_b>;
> > +};
> > +
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-t7.dtsi b/arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> > new file mode 100644
> > index 000000000000..453b3d9cb9d8
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> > @@ -0,0 +1,202 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> > + */
> > +
> > +#include <dt-bindings/clock/mesont7-clkc.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > + compatible = "amlogic,t7";
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + cpus {
> > + #address-cells = <0x2>;
> > + #size-cells = <0x0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&cpu100>;
> > + };
> > + core1 {
> > + cpu = <&cpu101>;
> > + };
> > + core2 {
> > + cpu = <&cpu102>;
> > + };
> > + core3 {
> > + cpu = <&cpu103>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&cpu0>;
> > + };
> > + core1 {
> > + cpu = <&cpu1>;
> > + };
> > + core2 {
> > + cpu = <&cpu2>;
> > + };
> > + core3 {
> > + cpu = <&cpu3>;
> > + };
> > + };
> > + };
> > +
> > + cpu100: cpu@100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x0 0x100>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <632>;
> > + dynamic-power-coefficient = <110>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu101: cpu@101{
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x0 0x101>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <632>;
> > + dynamic-power-coefficient = <110>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu102: cpu@102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x0 0x102>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <632>;
> > + dynamic-power-coefficient = <110>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu103: cpu@103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x0 0x103>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <632>;
> > + dynamic-power-coefficient = <110>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu0: cpu@0 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a73";
> > + reg = <0x0 0x0>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <1024>;
> > + dynamic-power-coefficient = <550>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu1: cpu@1 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a73";
> > + reg = <0x0 0x1>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <1024>;
> > + dynamic-power-coefficient = <550>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu2: cpu@2 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a73";
> > + reg = <0x0 0x2>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <1024>;
> > + dynamic-power-coefficient = <550>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu3: cpu@3 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a73";
> > + reg = <0x0 0x3>;
> > + enable-method = "psci";
> > + capacity-dmips-mhz = <1024>;
> > + dynamic-power-coefficient = <550>;
> > + #cooling-cells = <2>;
> > + };
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 0xff08>,
> > + <GIC_PPI 14 0xff08>,
> > + <GIC_PPI 11 0xff08>,
> > + <GIC_PPI 10 0xff08>;
> > + };
> > +
> > + gic: interrupt-controller@fff01000 {
> > + compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
> > + #interrupt-cells = <3>;
> > + #address-cells = <0>;
> > + interrupt-controller;
> > + reg = <0x0 0xfff01000 0 0x1000>,
> > + <0x0 0xfff02000 0 0x0100>;
> > + interrupts = <GIC_PPI 9 0xf04>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> can you double check if it is actual version 0.2?
> most recent Amlogic SoC should support psci-1.0
>
> > + method = "smc";
> > + };
> > +
> > + sm: secure-monitor {
> > + compatible = "amlogic,meson-gxbb-sm";
> > + };
> > +
> > + soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + apb4: apb4@fe000000 {
> > + compatible = "simple-bus";
> > + reg = <0x0 0xfe000000 0x0 0x480000>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
> > +
> > + clkc: clock-controller {
> > + compatible = "amlogic,t7-clkc";
> > + #clock-cells = <1>;
> > + reg = <0x0 0x0 0x0 0x49c>,
> > + <0x0 0x8000 0x0 0x320>,
> > + <0x0 0xe040 0x0 0xbc>;
> > + reg-names = "basic",
> > + "pll",
> > + "cpu_clk";
> > + };
> > +
> > + ao-secure@140 {
> > + compatible = "amlogic,meson-gx-ao-secure", "syscon";
> > + reg=<0x0 0x10220 0x0 0x140>;
> > + amlogic,has-chip-id;
> > + };
> > + };
> > +
> > + uart_A: serial@fe078000 {
> > + compatible = "amlogic,meson-t7-uart";
> > + reg = <0x0 0xfe078000 0x0 0x18>;
> > + interrupts = <0 168 1>;
> > + status = "disabled";
> > + clocks = <&xtal>, <&clkc CLKID_UART_A>, <&xtal>;
> > + clock-names = "xtal", "pclk", "baud";
> > + fifo-size = < 64 >;
> > + pinctrl-names = "default";
> > + };
> I believe there are more uart ports, it's worth the effort to add them all in one run,
> which sounds more consistent to me, anyway you could also choose to add them
> in later patch series, no problem..

Yeah, I prefer to add those uarts later, when I can propper test them.

>
> > + };
> > +};
> > +
> > --
> > 2.41.0
> >
> >
> > _______________________________________________
> > linux-amlogic mailing list
> > linux-amlogic@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-amlogic
>
> --
> Yixun Lan (dlan)
> Gentoo Linux Developer
> GPG Key ID AABEFD55

Next message: Lucas Tanure: "Re: [PATCH 3/6] clk: meson: t7: add peripheral clock controller"
Previous message: Lucas Tanure: "Re: [PATCH 5/6] tty: serial: meson: Added T7 SOC compatibility"
Next in thread: Lucas Tanure: "Re: [PATCH 6/6] arm64: dts: meson-t7-a311d2-khadas-vim4: add initial device-tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]