[PATCH AUTOSEL 6.3 20/30] i2c: designware: fix idx_write_cnt in read loop

From: Sasha Levin
Date: Fri Jun 16 2023 - 06:28:09 EST


From: David Zheng <david.zheng@xxxxxxxxx>

[ Upstream commit 1acfc6e753ed978b36d722f54e57fe4d1e8a6ffa ]

With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until
RX FIFO is empty. When testing with the slave-eeprom, each transaction
has 2 bytes for address/index and 1 byte for value, the address byte
can be written as data byte due to dropping STOP condition.

In the test below, the master continuously writes to the slave, first 2
bytes are index, 3rd byte is value and follow by a STOP condition.

i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3]

Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so
next 2 bytes can be treated as buffer index for upcoming transaction.
Supposedly the slave eeprom buffer would be written as

EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0xD2
EEPROM[0x00D3] = 0xD3

When CPU load is high the slave irq handler may not read fast enough,
the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET
(0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see
the transactions below.

0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4

After `D1` is received, read loop continues to read `00` which is the
first bype of next index. Since STOP condition is ignored by the loop,
eeprom buffer index increased to `D2` and `00` is written as value.

So the slave eeprom buffer becomes

EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0x00
EEPROM[0x00D3] = 0xD3

The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split
the transactions. The first index byte in this case would have bit 11
set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event
which will reset `idx_write_cnt` in slave eeprom.

Signed-off-by: David Zheng <david.zheng@xxxxxxxxx>
Acked-by: Jarkko Nikula <jarkko.nikula@xxxxxxxxxxxxxxx>
Signed-off-by: Wolfram Sang <wsa@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
drivers/i2c/busses/i2c-designware-core.h | 1 +
drivers/i2c/busses/i2c-designware-slave.c | 4 ++++
2 files changed, 5 insertions(+)

diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index 050d8c63ad3c5..0164d92163308 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -40,6 +40,7 @@
#define DW_IC_CON_BUS_CLEAR_CTRL BIT(11)

#define DW_IC_DATA_CMD_DAT GENMASK(7, 0)
+#define DW_IC_DATA_CMD_FIRST_DATA_BYTE BIT(11)

/*
* Registers offset
diff --git a/drivers/i2c/busses/i2c-designware-slave.c b/drivers/i2c/busses/i2c-designware-slave.c
index cec25054bb244..2e079cf20bb5b 100644
--- a/drivers/i2c/busses/i2c-designware-slave.c
+++ b/drivers/i2c/busses/i2c-designware-slave.c
@@ -176,6 +176,10 @@ static irqreturn_t i2c_dw_isr_slave(int this_irq, void *dev_id)

do {
regmap_read(dev->map, DW_IC_DATA_CMD, &tmp);
+ if (tmp & DW_IC_DATA_CMD_FIRST_DATA_BYTE)
+ i2c_slave_event(dev->slave,
+ I2C_SLAVE_WRITE_REQUESTED,
+ &val);
val = tmp;
i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_RECEIVED,
&val);
--
2.39.2