[PATCH 1/2] arm64: dts: qcom: ipq9574: Add common RDP dtsi file
From: Anusha Rao
Date: Wed Jun 14 2023 - 04:51:50 EST
Add a dtsi file to include interfaces that are common
across RDPs.
Signed-off-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
---
.../boot/dts/qcom/ipq9574-rdp-common.dtsi | 121 ++++++++++++++++++
arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts | 107 +---------------
arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 88 +------------
arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts | 65 +---------
arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts | 65 +---------
5 files changed, 125 insertions(+), 321 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
new file mode 100644
index 000000000000..999902bc70bd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 RDP board common device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq9574.dtsi"
+
+/ {
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&blsp1_spi0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash@0 {
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-mp5496-regulators";
+
+ ipq9574_s1: s1 {
+ /*
+ * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
+ * During regulator registration, kernel not knowing the initial voltage,
+ * considers it as zero and brings up the regulators with minimum supported voltage.
+ * Update the regulator-min-microvolt with SVS voltage of 725mV so that
+ * the regulators are brought up with 725mV which is sufficient for all the
+ * corner parts to operate at 800MHz
+ */
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1075000>;
+ };
+ };
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc_default_state>;
+ pinctrl-names = "default";
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ max-frequency = <384000000>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ sdc_default_state: sdc-default-state {
+ clk-pins {
+ pins = "gpio5";
+ function = "sdc_clk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "gpio4";
+ function = "sdc_cmd";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "gpio0", "gpio1", "gpio2",
+ "gpio3", "gpio6", "gpio7",
+ "gpio8", "gpio9";
+ function = "sdc_data";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ rclk-pins {
+ pins = "gpio10";
+ function = "sdc_rclk";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ spi_0_pins: spi-0-state {
+ pins = "gpio11", "gpio12", "gpio13", "gpio14";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
+};
+
+&xo_board_clk {
+ clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
index 2b093e02637b..924e4c50101a 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp418.dts
@@ -8,117 +8,12 @@
/dts-v1/;
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
/ {
model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C2";
compatible = "qcom,ipq9574-ap-al02-c2", "qcom,ipq9574";
- aliases {
- serial0 = &blsp1_uart2;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&blsp1_spi0 {
- pinctrl-0 = <&spi_0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- flash@0 {
- compatible = "micron,n25q128a11", "jedec,spi-nor";
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- };
-};
-
-&blsp1_uart2 {
- pinctrl-0 = <&uart2_pins>;
- pinctrl-names = "default";
- status = "okay";
};
-&rpm_requests {
- regulators {
- compatible = "qcom,rpm-mp5496-regulators";
-
- ipq9574_s1: s1 {
- /*
- * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
- * During regulator registration, kernel not knowing the initial voltage,
- * considers it as zero and brings up the regulators with minimum supported voltage.
- * Update the regulator-min-microvolt with SVS voltage of 725mV so that
- * the regulators are brought up with 725mV which is sufficient for all the
- * corner parts to operate at 800MHz
- */
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1075000>;
- };
- };
-};
-
-&sdhc_1 {
- pinctrl-0 = <&sdc_default_state>;
- pinctrl-names = "default";
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- mmc-hs400-enhanced-strobe;
- max-frequency = <384000000>;
- bus-width = <8>;
- status = "okay";
-};
-&sleep_clk {
- clock-frequency = <32000>;
-};
-
-&tlmm {
- sdc_default_state: sdc-default-state {
- clk-pins {
- pins = "gpio5";
- function = "sdc_clk";
- drive-strength = <8>;
- bias-disable;
- };
-
- cmd-pins {
- pins = "gpio4";
- function = "sdc_cmd";
- drive-strength = <8>;
- bias-pull-up;
- };
-
- data-pins {
- pins = "gpio0", "gpio1", "gpio2",
- "gpio3", "gpio6", "gpio7",
- "gpio8", "gpio9";
- function = "sdc_data";
- drive-strength = <8>;
- bias-pull-up;
- };
-
- rclk-pins {
- pins = "gpio10";
- function = "sdc_rclk";
- drive-strength = <8>;
- bias-pull-down;
- };
- };
-
- spi_0_pins: spi-0-state {
- pins = "gpio11", "gpio12", "gpio13", "gpio14";
- function = "blsp0_spi";
- drive-strength = <8>;
- bias-disable;
- };
-};
-
-&xo_board_clk {
- clock-frequency = <24000000>;
-};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 2b3ed8d351f7..ae2578ba6980 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -8,96 +8,10 @@
/dts-v1/;
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
/ {
model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7";
compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
- aliases {
- serial0 = &blsp1_uart2;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&blsp1_uart2 {
- pinctrl-0 = <&uart2_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&rpm_requests {
- regulators {
- compatible = "qcom,rpm-mp5496-regulators";
-
- ipq9574_s1: s1 {
- /*
- * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
- * During regulator registration, kernel not knowing the initial voltage,
- * considers it as zero and brings up the regulators with minimum supported voltage.
- * Update the regulator-min-microvolt with SVS voltage of 725mV so that
- * the regulators are brought up with 725mV which is sufficient for all the
- * corner parts to operate at 800MHz
- */
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1075000>;
- };
- };
-};
-
-&sdhc_1 {
- pinctrl-0 = <&sdc_default_state>;
- pinctrl-names = "default";
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- mmc-hs400-enhanced-strobe;
- max-frequency = <384000000>;
- bus-width = <8>;
- status = "okay";
-};
-
-&sleep_clk {
- clock-frequency = <32000>;
-};
-
-&tlmm {
- sdc_default_state: sdc-default-state {
- clk-pins {
- pins = "gpio5";
- function = "sdc_clk";
- drive-strength = <8>;
- bias-disable;
- };
-
- cmd-pins {
- pins = "gpio4";
- function = "sdc_cmd";
- drive-strength = <8>;
- bias-pull-up;
- };
-
- data-pins {
- pins = "gpio0", "gpio1", "gpio2",
- "gpio3", "gpio6", "gpio7",
- "gpio8", "gpio9";
- function = "sdc_data";
- drive-strength = <8>;
- bias-pull-up;
- };
-
- rclk-pins {
- pins = "gpio10";
- function = "sdc_rclk";
- drive-strength = <8>;
- bias-pull-down;
- };
- };
-};
-
-&xo_board_clk {
- clock-frequency = <24000000>;
};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
index c8fa54e1a62c..d36d1078763e 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp449.dts
@@ -8,73 +8,10 @@
/dts-v1/;
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
/ {
model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C6";
compatible = "qcom,ipq9574-ap-al02-c6", "qcom,ipq9574";
- aliases {
- serial0 = &blsp1_uart2;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&blsp1_spi0 {
- pinctrl-0 = <&spi_0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- flash@0 {
- compatible = "micron,n25q128a11", "jedec,spi-nor";
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- };
-};
-
-&blsp1_uart2 {
- pinctrl-0 = <&uart2_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&rpm_requests {
- regulators {
- compatible = "qcom,rpm-mp5496-regulators";
-
- ipq9574_s1: s1 {
- /*
- * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
- * During regulator registration, kernel not knowing the initial voltage,
- * considers it as zero and brings up the regulators with minimum supported voltage.
- * Update the regulator-min-microvolt with SVS voltage of 725mV so that
- * the regulators are brought up with 725mV which is sufficient for all the
- * corner parts to operate at 800MHz
- */
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1075000>;
- };
- };
-};
-
-&sleep_clk {
- clock-frequency = <32000>;
-};
-
-&tlmm {
- spi_0_pins: spi-0-state {
- pins = "gpio11", "gpio12", "gpio13", "gpio14";
- function = "blsp0_spi";
- drive-strength = <8>;
- bias-disable;
- };
-};
-
-&xo_board_clk {
- clock-frequency = <24000000>;
};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
index f01de6628c3b..c30c9fbedf26 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp453.dts
@@ -8,73 +8,10 @@
/dts-v1/;
-#include "ipq9574.dtsi"
+#include "ipq9574-rdp-common.dtsi"
/ {
model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C8";
compatible = "qcom,ipq9574-ap-al02-c8", "qcom,ipq9574";
- aliases {
- serial0 = &blsp1_uart2;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&blsp1_spi0 {
- pinctrl-0 = <&spi_0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- flash@0 {
- compatible = "micron,n25q128a11", "jedec,spi-nor";
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- };
-};
-
-&blsp1_uart2 {
- pinctrl-0 = <&uart2_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&rpm_requests {
- regulators {
- compatible = "qcom,rpm-mp5496-regulators";
-
- ipq9574_s1: s1 {
- /*
- * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
- * During regulator registration, kernel not knowing the initial voltage,
- * considers it as zero and brings up the regulators with minimum supported voltage.
- * Update the regulator-min-microvolt with SVS voltage of 725mV so that
- * the regulators are brought up with 725mV which is sufficient for all the
- * corner parts to operate at 800MHz
- */
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1075000>;
- };
- };
-};
-
-&sleep_clk {
- clock-frequency = <32000>;
-};
-
-&tlmm {
- spi_0_pins: spi-0-state {
- pins = "gpio11", "gpio12", "gpio13", "gpio14";
- function = "blsp0_spi";
- drive-strength = <8>;
- bias-disable;
- };
-};
-
-&xo_board_clk {
- clock-frequency = <24000000>;
};
--
2.17.1