Re: [PATCH V2 11/13] arm64: dtsi: qcom: ipq5018: enable nodes required for multipd

[Manikanta Mylavarapu]

On 6/5/2023 11:05 AM, Manikanta Mylavarapu wrote:
> On 5/30/2023 4:35 PM, Krzysztof Kozlowski wrote:
> > On 22/05/2023 00:28, Manikanta Mylavarapu wrote:
> > > Enable nodes required for multipd remoteproc bring up
> >
> > Please use subject prefixes matching the subsystem. You can get them for
> > example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
> > your patch is touching.
> >
> > It is "dts". Not "dtsi".
> Sure, I will update to 'dtsi'.
Sorry please discard my previous reply.
I will update to dts.

> > > Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@xxxxxxxxxxx>
> > > ---
> > > Changes in V2:
> > >     - Corrected syntax like alignmnet and kept nodes in sorted order.
> > >     - Covered entire TCSR region.
> > >     - Added 'firmware-name' property.
> > >
> > >   arch/arm64/boot/dts/qcom/ipq5018.dtsi | 140 ++++++++++++++++++++++++++
> > >   1 file changed, 140 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi 
> > > b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> > > index 9f13d2dcdfd5..3772d54d89e4 100644
> > > --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> > > @@ -85,6 +85,18 @@
> > >               reg = <0x0 0x4ac00000 0x0 0x200000>;
> > >               no-map;
> > >           };
> > > +
> > > +        q6_region: wcnss@4b000000 {
> > > +            reg = <0x0 0x4b000000 0x0 0x1700000>;
> > > +            no-map;
> > > +        };
> > > +
> > > +        smem@4ab00000 {
> > > +            compatible = "qcom,smem";
> > > +            reg = <0x0 0x4ab00000 0x0 0x100000>;
> > > +            hwlocks = <&tcsr_mutex 0>;
> > > +            no-map;
> > > +        };
> > >       };
> > >
> > >       soc: soc@0 {
> > > @@ -128,6 +140,12 @@
> > >               #power-domain-cells = <1>;
> > >           };
> > >
> > > +        tcsr_mutex: hwlock@1905000 {
> > > +            compatible = "qcom,tcsr-mutex";
> > > +            reg = <0x01905000 0x20000>;
> > > +            #hwlock-cells = <1>;
> > > +        };
> > > +
> > >           sdhc_1: mmc@7804000 {
> > >               compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5";
> > >               reg = <0x7804000 0x1000>;
> > > @@ -181,6 +199,14 @@
> > >               };
> > >           };
> > >
> > > +        apcs_glb: mailbox@b111000 {
> > > +            compatible = "qcom,ipq5018-apcs-apps-global",
> > > +                     "qcom,ipq6018-apcs-apps-global";
> > > +            reg = <0x0b111000 0x1000>;
> > > +            #clock-cells = <1>;
> > > +            #mbox-cells = <1>;
> > > +        };
> > > +
> > >           timer@b120000 {
> > >               compatible = "arm,armv7-timer-mem";
> > >               reg = <0x0b120000 0x1000>;
> > > @@ -238,6 +264,96 @@
> > >                   status = "disabled";
> > >               };
> > >           };
> > > +
> > > +        q6v5_wcss: remoteproc@cd00000 {
> > > +            compatible = "qcom,ipq5018-q6-mpd";
> > > +            reg = <0x0cd00000 0x4040>;
> > > +            firmware-name = "IPQ5018/q6_fw.mdt",
> > > +                    "IPQ5018/m3_fw.mdt",
> > > +                    "qcn6122/m3_fw.mdt";
> > > +            interrupts-extended = <&intc GIC_SPI 291 
> > > IRQ_TYPE_EDGE_RISING>,
> > > +                          <&wcss_smp2p_in 0 0>,
> > > +                          <&wcss_smp2p_in 1 0>,
> > > +                          <&wcss_smp2p_in 2 0>,
> > > +                          <&wcss_smp2p_in 3 0>;
> > > +            interrupt-names = "wdog",
> > > +                      "fatal",
> > > +                      "ready",
> > > +                      "handover",
> > > +                      "stop-ack";
> > > +
> > > +            qcom,smem-states = <&wcss_smp2p_out 0>,
> > > +                       <&wcss_smp2p_out 1>;
> > > +            qcom,smem-state-names = "shutdown",
> > > +                        "stop";
> > > +            memory-region = <&q6_region>;
> > > +
> > > +            glink-edge {
> > > +                interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
> > > +                label = "rtr";
> > > +                qcom,remote-pid = <1>;
> > > +                mboxes = <&apcs_glb 8>;
> > > +            };
> > > +
> > > +            pd-1 {
> > > +                compatible = "qcom,ipq5018-wcss-ahb-mpd";
> > > +                firmware-name = "IPQ5018/q6_fw.mdt";
> > > +                interrupts-extended = <&wcss_smp2p_in 8 0>,
> > > +                              <&wcss_smp2p_in 9 0>,
> > > +                              <&wcss_smp2p_in 12 0>,
> > > +                              <&wcss_smp2p_in 11 0>;
> >
> > What "0" stands for?
> 0 means IRQ_NONE. These are software interrupts (register write),
> so we have configured to 0. I will replace 0 with IRQ_NONE.
>
> Thanks & Regards,
> Manikanta.
>
> > > +                interrupt-names = "fatal",
> > > +                          "ready",
> > Best regards,
> > Krzysztof