[PATCH v4 4/4] riscv: dts: starfive: jh7100: Add PWM node and pins configuration

[William Qiu]

Add StarFive JH7100 PWM controller node and add PWM pins configuration
on VisionFive 2 board.

Reviewed-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
Signed-off-by: William Qiu <william.qiu@xxxxxxxxxxxxxxxx>
---
 .../boot/dts/starfive/jh7100-common.dtsi      | 24 +++++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7100.dtsi      |  9 +++++++
 2 files changed, 33 insertions(+)

diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
index b93ce351a90f..746867b882b0 100644
--- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
@@ -84,6 +84,24 @@ GPO_I2C2_PAD_SDA_OEN,
 		};
 	};
 
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(7,
+				  GPO_PWM_PAD_OUT_BIT0,
+				  GPO_PWM_PAD_OE_N_BIT0,
+				  GPI_NONE)>,
+				 <GPIOMUX(5,
+				  GPO_PWM_PAD_OUT_BIT1,
+				  GPO_PWM_PAD_OE_N_BIT1,
+				  GPI_NONE)>;
+			bias-disable;
+			drive-strength = <35>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
 	uart3_pins: uart3-0 {
 		rx-pins {
 			pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
@@ -154,6 +172,12 @@ &osc_aud {
 	clock-frequency = <27000000>;
 };
 
+&ptc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi
index 000447482aca..977a509ffbdd 100644
--- a/arch/riscv/boot/dts/starfive/jh7100.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi
@@ -238,5 +238,14 @@ i2c3: i2c@12460000 {
 			#size-cells = <0>;
 			status = "disabled";
 		};
+
+		ptc: pwm@12490000 {
+			compatible = "starfive,jh7100-pwm";
+			reg = <0x0 0x12490000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_PWM_APB>;
+			resets = <&rstgen JH7100_RSTN_PWM_APB>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
 	};
 };
-- 
2.34.1