Re: [PATCH] arm64: dts: imx8mm: add support for compulab iot gateway

From: Krzysztof Kozlowski
Date: Fri May 12 2023 - 02:17:23 EST

Next message: Krzysztof Kozlowski: "Re: [PATCH v2 3/5] dt-bindings: net: add mac-address-increment option"
Previous message: Parthiban Nallathambi: "[PATCH] arm64: dts: imx8mm: add support for compulab iot gateway"
In reply to: Parthiban Nallathambi: "[PATCH] arm64: dts: imx8mm: add support for compulab iot gateway"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 12/05/2023 07:52, Parthiban Nallathambi wrote:
> Add support for compulab for imx8mm IoT gateway with
> UCM-iMX8M-Mini SoM. IoT gateway comes with dual ethernet,
> USB and IO expansion.
>
> WLAN, Bluetooth can be part of SoM or extended over PCIE.
>
> Signed-off-by: Parthiban Nallathambi <parthiban@xxxxxxxxxxx>
> ---
> .../devicetree/bindings/arm/fsl.yaml | 2 +
> .../bindings/net/microchip,lan95xx.yaml | 1 +
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../freescale/imx8mm-compulab-iot-gate.dts | 315 +++++++++++
> .../dts/freescale/imx8mm-compulab-ucm.dtsi | 532 ++++++++++++++++++
> 5 files changed, 851 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-compulab-iot-gate.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-compulab-ucm.dtsi
>
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 15d411084065..d2425c5ed4b7 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -895,6 +895,8 @@ properties:
> - description: i.MX8MM based Boards
> items:
> - enum:
> + - compulab,imx8mm-ucm-som # UCM-iMX8M-Mini Compulab SoM
> + - compulab,iot-gate-imx8 # iMX8M IoT Compulab Gateway with UCM-iMX8M-Mini

Bindings are always separate patches.

Please run scripts/checkpatch.pl and fix reported warnings. Checkpatch
tells you this, so you apparently did not run it.

> - beacon,imx8mm-beacon-kit # i.MX8MM Beacon Development Kit
> - boundary,imx8mm-nitrogen8mm # i.MX8MM Nitrogen Board
> - dmo,imx8mm-data-modul-edm-sbc # i.MX8MM eDM SBC
> diff --git a/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml b/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml
> index 0b97e14d947f..86279724695e 100644
> --- a/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml
> +++ b/Documentation/devicetree/bindings/net/microchip,lan95xx.yaml
> @@ -22,6 +22,7 @@ properties:
> - enum:
> - usb424,9500 # SMSC9500 USB Ethernet Device
> - usb424,9505 # SMSC9505 USB Ethernet Device
> + - usb424,9514 # SMSC9514 USB Ethernet Device

No, really, I could understand squashing board bindings here but
changing drivers in the same patch is clearly too much.

> - usb424,9530 # SMSC LAN9530 USB Ethernet Device
> - usb424,9730 # SMSC LAN9730 USB Ethernet Device
> - usb424,9900 # SMSC9500 USB Ethernet Device (SAL10)
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ef7d17aef58f..2a613c576d29 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb
>
> dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-compulab-iot-gate.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-compulab-iot-gate.dts b/arch/arm64/boot/dts/freescale/imx8mm-compulab-iot-gate.dts
> new file mode 100644
> index 000000000000..678a9022549f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-compulab-iot-gate.dts
> @@ -0,0 +1,315 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2018 Compulab
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm-compulab-ucm.dtsi"
> +
> +/ {
> + model = "CompuLab IOT-GATE-iMX8 board";
> + compatible = "compulab,iot-gate-imx8", "compulab,imx8mm-ucm-som", "fsl,imx8mm";
> +
> + regulator-usbhub-ena {
> + compatible = "regulator-fixed";
> + regulator-name = "usbhub_ena";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + regulator-usbhub-rst {
> + compatible = "regulator-fixed";
> + regulator-name = "usbhub_rst";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 24 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + regulator-uart1-mode {
> + compatible = "regulator-fixed";
> + regulator-name = "uart1_mode";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + regulator-uart1-duplex {
> + compatible = "regulator-fixed";
> + regulator-name = "uart1_duplex";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + regulator-uart1-shdn {
> + compatible = "regulator-fixed";
> + regulator-name = "uart1_shdn";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + regulator-uart1-trmen {
> + compatible = "regulator-fixed";
> + regulator-name = "uart1_trmen";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 25 GPIO_ACTIVE_LOW>;
> + regulator-always-on;
> + enable-active-low;
> + };
> +
> + regulator-usdhc2_v {

No underscores in node names. Fix it everywhere.

> + compatible = "regulator-fixed";
> + regulator-name = "usdhc2_v";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + reg_usdhc2_rst: regulator-usdhc2_rst {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_rst>;
> + regulator-name = "usdhc2_rst";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + enable-active-high;
> + };
> +
> + regulator-mpcie2_rst {
> + compatible = "regulator-fixed";
> + regulator-name = "mpcie2_rst";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + regulator-mpcie2lora_dis {
> + compatible = "regulator-fixed";
> + regulator-name = "mpcie2lora_dis";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 21 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + enable-active-high;
> + };
> +
> + pcie0_refclk: pcie0-refclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + };
> +};
> +
> +&ethphy0 {
> + status = "okay";
> +};
> +
> +&fec1 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_gpio>;
> + assigned-clocks = <&clk IMX8MM_CLK_UART1>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> + linux,rs485-enabled-at-boot-time;
> + rts-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "disabled";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + eeprom@54 {
> + compatible = "atmel,24c08";
> + reg = <0x54>;
> + pagesize = <16>;
> + };
> +};
> +
> +&ecspi1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + fsl,spi-num-chipselects = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
> + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usb9514@1 {

Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> + compatible = "usb424,9514";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb9514>;
> + reg = <1>;

reg is always after compatible.

> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet: usbether@1 {
> + compatible = "usb424,ec00";
> + reg = <1>;
> + };
> + };
> +};
> +
> +&usdhc1 {
> + status = "disabled";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + bus-width = <4>;
> + mmc-ddr-1_8v;
> + non-removable;
> + vmmc-supply = <&reg_usdhc2_rst>;
> + status = "okay";
> +};
> +
> +&pcie0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie0>;
> + reset-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
> + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>,
> + <&clk IMX8MM_CLK_PCIE1_AUX>,
> + <&clk IMX8MM_CLK_PCIE1_PHY>,
> + <&pcie0_refclk>;
> + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> + assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
> + <&clk IMX8MM_CLK_PCIE1_PHY>,
> + <&clk IMX8MM_CLK_PCIE1_CTRL>;
> + assigned-clock-rates = <10000000>, <100000000>, <250000000>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
> + <&clk IMX8MM_SYS_PLL2_100M>,
> + <&clk IMX8MM_SYS_PLL2_250M>;
> + ext_osc = <1>;
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog_sb_iotgimx8>;
> +
> + sb-iotgimx8 {
> + pinctrl_hog_sb_iotgimx8: hoggrp_sb-iotgimx8 {

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

> + fsl,pins = <
> + /* mPCIe2 */
> + MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x140 /* LORA_DISABLE */
> + MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x140 /* PERSTn */
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140
> + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140
> + MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24 0x140 /* RTS */
> + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140 /* CTS */
> + >;
> + };
> +
> + pinctrl_uart1_gpio: uart1gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26 0x000 /* RS_485_232_SEL */
> + MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x140 /* RS_485_H/F_SEL */
> + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x140 /* SHDN */
> + MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25 0x140 /* RS_485_TRMEN */
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
> + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
> + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
> + >;
> + };
> +
> + pinctrl_ecspi1_cs: ecspi1cs {

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

I guess you did not test it at all.

> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x40000
> + >;
> + };
> +
> + pinctrl_usb9514: usb9514grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x140 /* USB_PS_EN */
> + MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x140 /* HUB_RSTn */
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> + MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x1d0 /* SD2_VSEL */
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_rst: usdhc2rst {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 /* EMMC_RST */
> + >;
> + };
> +
> + pinctrl_pcie0: pcie0grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x140
> + >;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-compulab-ucm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-compulab-ucm.dtsi
> new file mode 100644
> index 000000000000..d6cdf833744e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-compulab-ucm.dtsi
> @@ -0,0 +1,532 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2018 Compulab
> + */
> +
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "Compulab i.MX8M-Mini UCM SoM";
> + compatible = "compulab,imx8mm-ucm-som", "fsl,imx8mm";
> +
> + aliases {
> + rtc0 = &rtc0;
> + rtc1 = &snvs_rtc;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_led>;
> +
> + heartbeat-led {
> + label = "Heartbeat";
> + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + pmic_osc: clock-pmic {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "pmic_osc";
> + };
> +
> + reg_ethphy: regulator-ethphy {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_eth>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "On-module +V3.3_ETH";
> + startup-delay-us = <500>;
> + };
> +
> + reg_usdhc3_vmmc: regulator-usdhc3-vmmc {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc3>;
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "On-module +V3.3_USDHC";
> + };
> +
> + usdhc1_pwrseq: usdhc1_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&fec1 {
> + fsl,magic-packet;
> + fsl,rgmii_rxc_dly;
> + phy-handle = <&ethphy0>;
> + phy-mode = "rgmii-id";
> + phy-supply = <&reg_ethphy>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + micrel,led-mode = <0>;
> + reg = <0>;
> + };
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + rtc0: rtc@69 {
> + compatible = "abracon,ab1805";
> + reg = <0x69>;
> + };
> +
> + pmic: bd71837@4b {

Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

Best regards,
Krzysztof

Next message: Krzysztof Kozlowski: "Re: [PATCH v2 3/5] dt-bindings: net: add mac-address-increment option"
Previous message: Parthiban Nallathambi: "[PATCH] arm64: dts: imx8mm: add support for compulab iot gateway"
In reply to: Parthiban Nallathambi: "[PATCH] arm64: dts: imx8mm: add support for compulab iot gateway"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]