Re: [PATCH] mips: dts: ralink: Add support for TP-Link HC220 G5 v1 board.

[Arınç ÜNAL]

On 9.05.2023 22:01, Liviu Dudau wrote:
> This WiFi AP is based on a MT7621 SoC with 128MiB RAM, 128MiB NAND,
> a MT7603 2.4GHz WiFi and a MT7663 5GHz WiFi chips integrated on the board,
> connected to the main SoC over PCIe.
>
> The GMAC1 on the SoC is connected to PHY0 on the GSW and can be used to
> improve routing bandwidth.
>
> The device uses NMBM over NAND, which is not currently supported in the
> mainline, so NAND node is skipped in this revision.
>
> Signed-off-by: Liviu Dudau <liviu@xxxxxxxxxxx>

This is great to see. I'm going to mainline all the MT7621 devicetrees 
on OpenWrt at some point, this is a good step for this.

> ---
>   arch/mips/boot/dts/ralink/Makefile            |   3 +-
>   .../dts/ralink/mt7621-tplink-hc220_g5.dts     | 126 ++++++++++++++++++
>   2 files changed, 128 insertions(+), 1 deletion(-)
>   create mode 100644 arch/mips/boot/dts/ralink/mt7621-tplink-hc220_g5.dts
>
> diff --git a/arch/mips/boot/dts/ralink/Makefile b/arch/mips/boot/dts/ralink/Makefile
> index 11732b8c8163a..c57a2b40876b4 100644
> --- a/arch/mips/boot/dts/ralink/Makefile
> +++ b/arch/mips/boot/dts/ralink/Makefile
> @@ -8,6 +8,7 @@ dtb-$(CONFIG_DTB_VOCORE2)	+= vocore2.dtb
>   
>   dtb-$(CONFIG_SOC_MT7621) += \
>   	mt7621-gnubee-gb-pc1.dtb \
> -	mt7621-gnubee-gb-pc2.dtb
> +	mt7621-gnubee-gb-pc2.dtb \
> +	mt7621-tplink-hc220_g5.dtb
>   
>   obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
> diff --git a/arch/mips/boot/dts/ralink/mt7621-tplink-hc220_g5.dts b/arch/mips/boot/dts/ralink/mt7621-tplink-hc220_g5.dts
> new file mode 100644
> index 0000000000000..83d15711907d0
> --- /dev/null
> +++ b/arch/mips/boot/dts/ralink/mt7621-tplink-hc220_g5.dts
> @@ -0,0 +1,126 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/dts-v1/;
> +
> +#include "mt7621.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	compatible = "tplink,hc220-g5", "mediatek,mt7621-soc";

tplink,hc220-g5-v1 should fit better. Also please make another patch to 
add the compatible string under Boards with Mediatek/Ralink MT7621 SoC 
on Documentation/devicetree/bindings/mips/ralink.yaml.

> +	model = "TP-Link HC220 G5 v1.0";

"TP-Link HC220 G5 v1" should be enough.

> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x8000000>;
> +	};
> +
> +	chosen {
> +		/* bootargs = "earlycon=uart8260,mmio32,0x1e000c00 root=/dev/ram0 kgdboc=ttyS0,115200 ip=192.168.88.1:192.168.88.2:::hc220:eth1:none kgdbcon console=ttyS0,115200"; */
> +		/* bootargs = "console=ttyS0,115200 earlycon=uart8260,mmio32,0x1e000c00 root=/dev/ram0"; */
> +		bootargs = "console=ttyS0,115200 root=/dev/nfs ip=192.168.88.2:192.168.88.5::255.255.255.0:hc220_g5:eth1:none nfsroot=192.168.88.5:/mips,vers=4,sec=sys ro rootwait";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		key-reset {
> +			label = "reset";
> +			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_RESTART>;
> +		};
> +
> +		key-wps {
> +			label = "wps";
> +			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_WPS_BUTTON>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		red {
> +			color = <LED_COLOR_ID_RED>;
> +			function = LED_FUNCTION_FAULT;
> +			gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		green {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +
> +		blue {
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_WPS;
> +			gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +
> +	resetc: reset-controller {
> +		compatible = "ralink,rt2880-reset";
> +		#reset-cells = <1>;
> +	};
> +
> +	mtd {
> +		compatible = "mediatek,mt7622-nfc";
> +	};
> +};
> +
> +&i2c {
> +	status = "okay";
> +};
> +
> +&pcie {
> +	status = "okay";
> +};
> +
> +&spi0 {
> +	status = "okay";
> +
> +	flash@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <50000000>;
> +	};
> +};
> +
> +/* gmac1 connected to MT7530's phy0 */
> +&gmac1 {
> +	status = "okay";
> +	phy-handle = <&ethphy0>;
> +};
> +
> +&mdio {
> +	/* MT7530's phy0 */
> +	ethphy0: ethernet-phy@0 {
> +		reg = <0>;
> +		phy-mode = "rgmii";
> +	};
> +};

These are partially wrong, check the mt7621.dtsi on mainline. Or better, 
don't do it. I'm very close to adding support for changing the DSA 
conduit for user ports. I suggest you just add port@0 to the DSA switch 
node below.

> +
> +&switch0 {
> +	/* #gpio-cells = <2>;
> +	gpio-controller; */
> +
> +	ports {
> +		/* phy0 is muxed to gmac1 */
> +		/delete-node/ port@0;
> +
> +		port@1 {
> +			status = "okay";
> +			label = "lan1";
> +		};
> +
> +		port@2 {
> +			status = "okay";
> +			label = "wan";
> +		};
> +	};
> +};

Arınç