Re: linux-6.4 alsa sound broken

[Jeff Chua]

On Mon, May 1, 2023 at 10:52 PM Takashi Iwai <tiwai@xxxxxxx> wrote:
>
> On Mon, 01 May 2023 15:16:35 +0200,
> Jeff Chua wrote:
> >
> > On Mon, May 1, 2023 at 2:35 PM Takashi Iwai <tiwai@xxxxxxx> wrote:
> > >
> > > On Mon, 01 May 2023 06:36:49 +0200,
> > > Bagas Sanjaya wrote:
> > > >
> > > > On Mon, May 01, 2023 at 11:59:12AM +0800, Jeff Chua wrote:
> > > > > Latest git pull from Linus's tree ... playing a simple sound file will
> > > > > resulted in a lot of echo.
> > > > >
> > > > > Running on Lenovo X1 with ..
> > > > > 00:1f.3 Audio device: Intel Corporation Alder Lake PCH-P High
> > > > > Definition Audio Controller (rev 01)
> > > > >
> > > > > I've bisected and reverted the following patch fixed the problem.
> > > > >
> > > > > commit 9f656705c5faa18afb26d922cfc64f9fd103c38d
> > > >
> > > > Thanks for the regression report. However, where is your dmesg and/or ALSA log
> > > > when the regression occurs? What is the playback test file?
> > >
> > > Yes, in addition, which driver is used (provide the alsa-info.sh
> > > output at best), and which sound backend is used (pipewire, PA or
> > > dmix) with which application?
> >
> > /proc/asound# cat cards devices hwdep pcm timers version
> >  0 [PCH            ]: HDA-Intel - HDA Intel PCH
> >                       HDA Intel PCH at 0x603e1c8000 irq 147
> >   1:        : sequencer
> >   2: [ 0- 0]: digital audio playback
> >   3: [ 0- 0]: digital audio capture
> >   4: [ 0- 3]: digital audio playback
> >   5: [ 0- 7]: digital audio playback
> >   6: [ 0- 8]: digital audio playback
> >   7: [ 0- 9]: digital audio playback
> >   8: [ 0- 0]: hardware dependent
> >   9: [ 0- 2]: hardware dependent
> >  10: [ 0]   : control
> >  33:        : timer
> > 00-00: HDA Codec 0
> > 00-02: HDA Codec 2
> > 00-00: ALC287 Analog : ALC287 Analog : playback 1 : capture 1
> > 00-03: HDMI 0 : HDMI 0 : playback 1
> > 00-07: HDMI 1 : HDMI 1 : playback 1
> > 00-08: HDMI 2 : HDMI 2 : playback 1
> > 00-09: HDMI 3 : HDMI 3 : playback 1
> > G0: system timer : 10000.000us (10000000 ticks)
> > G3: HR timer : 0.001us (1000000000 ticks)
> > P0-0-0: PCM playback 0-0-0 : SLAVE
> > P0-0-1: PCM capture 0-0-1 : SLAVE
> > P0-3-0: PCM playback 0-3-0 : SLAVE
> > P0-7-0: PCM playback 0-7-0 : SLAVE
> > P0-8-0: PCM playback 0-8-0 : SLAVE
> > P0-9-0: PCM playback 0-9-0 : SLAVE
> > Advanced Linux Sound Architecture Driver Version k6.3.0.
> >
> >
> > # test playing with ...
> > aplay /usr/share/sounds/alsa/Side_Right.wav
> > Playing WAVE '/usr/share/sounds/alsa/Side_Right.wav' : Signed 16 bit
> > Little Endian, Rate 48000 Hz, Mono
> >
> > I'll try to capture the sound ... it's seems to just repeating every
> > second until the last second. So, if you just play a "beep", its ok.
>
> There was no description about which sound backend is used.  Is it
> PulseAudio, pipewire or dmix/dsnoop?

Just pure alsautils.

arecord -D hw:1,0,0 -f S16_LE -r 48000 recorded.wav
aplay -D hw:1,1,0 /local/share/sounds/alsa/Side_Right.wav

[recorded.wav] attached.
[Side_Right.wav] attached.
aplay: version 1.2.8 by Jaroslav Kysela <perex@xxxxxxxx>
arecord: version 1.2.8 by Jaroslav Kysela <perex@xxxxxxxx>

alsautils, alsaplugins alsalibs all using latest git pull.

Attachment: Side_Right.wav
Description: Wave audio