Re: [PATCH v1 2/2] net: phy: motorcomm: Add pad drive strength cfg support

[Frank Sae]

On 2023/4/26 14:35, Samin Guo wrote:
> The motorcomm phy (YT8531) supports the ability to adjust the drive
> strength of the rx_clk/rx_data, and the default strength may not be
> suitable for all boards. So add configurable options to better match
> the boards.(e.g. StarFive VisionFive 2)
> 
> Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
> ---
>  drivers/net/phy/motorcomm.c | 32 ++++++++++++++++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
> index 2fa5a90e073b..08f28ed83e60 100644
> --- a/drivers/net/phy/motorcomm.c
> +++ b/drivers/net/phy/motorcomm.c
> @@ -236,6 +236,11 @@
>   */
>  #define YTPHY_WCR_TYPE_PULSE			BIT(0)
>  
> +#define YTPHY_PAD_DRIVE_STRENGTH_REG		0xA010
> +#define YTPHY_RGMII_RXC_DS			GENMASK(15, 13)
> +#define YTPHY_RGMII_RXD_DS			GENMASK(5, 4)	/* Bit 1 and 0 of rgmii_rxd_ds */
> +#define YTPHY_RGMII_RXD_DS2			BIT(12) 	/* Bit 2 of rgmii_rxd_ds */
> +

Please  change YTPHY_RGMII_XXX  to YT8531_RGMII_XXX. YT8521's reg (0xA010) is not same as this.
Keep bit order.

>  #define YTPHY_SYNCE_CFG_REG			0xA012
>  #define YT8521_SCR_SYNCE_ENABLE			BIT(5)
>  /* 1b0 output 25m clock
> @@ -1495,6 +1500,7 @@ static int yt8531_config_init(struct phy_device *phydev)
>  {
>  	struct device_node *node = phydev->mdio.dev.of_node;
>  	int ret;
> +	u32 val;
>  
>  	ret = ytphy_rgmii_clk_delay_config_with_lock(phydev);
>  	if (ret < 0)
> @@ -1518,6 +1524,32 @@ static int yt8531_config_init(struct phy_device *phydev)
>  			return ret;
>  	}
>  
> +	if (!of_property_read_u32(node, "rx-clk-driver-strength", &val)) {

Please check the val of "val", add the handle of default value.

> +		ret = ytphy_modify_ext_with_lock(phydev,
> +						 YTPHY_PAD_DRIVE_STRENGTH_REG,
> +						 YTPHY_RGMII_RXC_DS,
> +						 FIELD_PREP(YTPHY_RGMII_RXC_DS, val));
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	if (!of_property_read_u32(node, "rx-data-driver-strength", &val)) {
> +		if (val > FIELD_MAX(YTPHY_RGMII_RXD_DS)) {
> +			val &= FIELD_MAX(YTPHY_RGMII_RXD_DS);
> +			val = FIELD_PREP(YTPHY_RGMII_RXD_DS, val);
> +			val |= YTPHY_RGMII_RXD_DS2;
> +		} else {
> +			val = FIELD_PREP(YTPHY_RGMII_RXD_DS, val);
> +		}
> +
> +		ret = ytphy_modify_ext_with_lock(phydev,
> +						 YTPHY_PAD_DRIVE_STRENGTH_REG,
> +						 YTPHY_RGMII_RXD_DS | YTPHY_RGMII_RXD_DS2,
> +						 val);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
>  	return 0;
>  }
>