Re: [PATCH 2/2] hwmon: ltc2945: Allow setting shunt resistor

From: Jon Cormier
Date: Thu Dec 15 2022 - 14:42:56 EST

On Thu, Dec 15, 2022 at 10:11 AM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>
> On 12/14/22 14:07, Cormier, Jonathan wrote:
> > From: John Pruitt <jpruitt@xxxxxxxxxxxxxxxx>
> >
> > Added the ability to specify the value of the shunt resistor in the
> > device tree instead of assuming it is 1 milliOhm. The value in the
> > device tree has the name shunt-resistor-micro-ohms and the
> > default value is 1000 micro-ohms in order to preserve the
> > current behavior.
> >
>
> Also needs a devicetree match table.
On it
>
> > Signed-off-by: "Cormier, Jonathan" <jcormier@xxxxxxxxxxxxxxxx>
> > Signed-off-by: John Pruitt <jpruitt@xxxxxxxxxxxxxxxx>
> > ---
> > drivers/hwmon/ltc2945.c | 86 +++++++++++++++++++++++++++++++----------
> > 1 file changed, 65 insertions(+), 21 deletions(-)
> >
> > diff --git a/drivers/hwmon/ltc2945.c b/drivers/hwmon/ltc2945.c
> > index 9adebb59f604..4e8b92e53133 100644
> > --- a/drivers/hwmon/ltc2945.c
> > +++ b/drivers/hwmon/ltc2945.c
> > @@ -58,6 +58,11 @@
> > #define CONTROL_MULT_SELECT (1 << 0)
> > #define CONTROL_TEST_MODE (1 << 4)
> >
> > +struct ltc2945_data {
> > + struct regmap *regmap;
> > + u32 shunt_resistor; // number of microohms
>
> No C++ comments in this code, please. Also, "number of" is not needed.
> Something like "in microohms" or just "microohms" would be sufficient.
>
> > +};
> > +
> > static inline bool is_power_reg(u8 reg)
> > {
> > return reg < LTC2945_SENSE_H;
> > @@ -66,7 +71,9 @@ static inline bool is_power_reg(u8 reg)
> > /* Return the value from the given register in uW, mV, or mA */
> > static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
> > {
> > - struct regmap *regmap = dev_get_drvdata(dev);
> > + struct ltc2945_data *data = dev_get_drvdata(dev);
> > + struct regmap *regmap = data->regmap;
> > + u32 shunt_resistor = data->shunt_resistor;
> > unsigned int control;
> > u8 buf[3];
> > long long val;
> > @@ -93,8 +100,11 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
> > case LTC2945_MIN_POWER_THRES_H:
> > /*
> > * Convert to uW by assuming current is measured with
> > - * an 1mOhm sense resistor, similar to current
> > - * measurements.
> > + * a 1000 microOhm sense resistor (aka shunt resistor)
> > + * or what is specified in DT, similar to current
> > + * measurements. The shunt_resistor value is in
> > + * microOhms.
>
> The units are already in the variable declaration. No need to repeat.
> There is no need to replace "1 mOhm" with "1000 microOhm".
>
> It might make sense to drop all those comments, add a kerneldoc comment
> to struct ltc2945_data, and explain it all there.
Will do
>
> > + *
> > * Control register bit 0 selects if voltage at SENSE+/VDD
> > * or voltage at ADIN is used to measure power.
> > */
> > @@ -108,6 +118,8 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
> > /* 0.5 mV * 25 uV = 0.0125 uV resolution. */
> > val = (val * 25LL) >> 1;
> > }
> > + val *= 1000;
> > + val = DIV_ROUND_CLOSEST_ULL(val, shunt_resistor);
> > break;
> > case LTC2945_VIN_H:
> > case LTC2945_MAX_VIN_H:
> > @@ -132,12 +144,15 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
> > case LTC2945_MIN_SENSE_THRES_H:
> > /*
> > * 25 uV resolution. Convert to current as measured with
> > - * an 1 mOhm sense resistor, in mA. If a different sense
> > - * resistor is installed, calculate the actual current by
> > - * dividing the reported current by the sense resistor value
> > - * in mOhm.
> > + * an 1000 microOhm sense (or shunt) resistor, in mA.
> > + * If a different shunt resistor is installed, calculate
> > + * the actual current by dividing the reported current
> > + * by the shunt resistor value in microOhms. The actual
> > + * The actual shunt resistor value can be specified
> > + * in the device tree.
>
> All but the last sentence just replace 1 mOhm with 1000 microOhm, which
> does not add any value. Applies to all similar changes; I won't comment
> on it anymore below.
>
> > */
> > - val *= 25;
> > + val *= 25 * 1000;
> > + val = DIV_ROUND_CLOSEST_ULL(val, shunt_resistor);
> > break;
> > default:
> > return -EINVAL;
> > @@ -148,7 +163,9 @@ static long long ltc2945_reg_to_val(struct device *dev, u8 reg)
> > static int ltc2945_val_to_reg(struct device *dev, u8 reg,
> > unsigned long val)
> > {
> > - struct regmap *regmap = dev_get_drvdata(dev);
> > + struct ltc2945_data *data = dev_get_drvdata(dev);
> > + struct regmap *regmap = data->regmap;
> > + u32 shunt_resistor = data->shunt_resistor;
> > unsigned int control;
> > int ret;
> >
> > @@ -160,8 +177,10 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
> > case LTC2945_MIN_POWER_THRES_H:
> > /*
> > * Convert to register value by assuming current is measured
> > - * with an 1mOhm sense resistor, similar to current
> > + * with a 1000 microOhm sense resistor, (aka shunt resistor)
> > + * or what is specified in DT, similar to current
> > * measurements.
> > + *
> > * Control register bit 0 selects if voltage at SENSE+/VDD
> > * or voltage at ADIN is used to measure power, which in turn
> > * determines register calculations.
> > @@ -171,14 +190,16 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
> > return ret;
> > if (control & CONTROL_MULT_SELECT) {
> > /* 25 mV * 25 uV = 0.625 uV resolution. */
> > - val = DIV_ROUND_CLOSEST(val, 625);
> > + val *= shunt_resistor;
>
> This can now easily result in an overflow.
Okay will fix
>
> > + val = DIV_ROUND_CLOSEST(val, 625 * 1000);
> > } else {
> > /*
> > * 0.5 mV * 25 uV = 0.0125 uV resolution.
> > * Divide first to avoid overflow;
> > * accept loss of accuracy.
> > */
> > - val = DIV_ROUND_CLOSEST(val, 25) * 2;
> > + val *= shunt_resistor;
> > + val = DIV_ROUND_CLOSEST(val, 25 * 1000) * 2;
> > }
> > break;
> > case LTC2945_VIN_H:
> > @@ -204,12 +225,14 @@ static int ltc2945_val_to_reg(struct device *dev, u8 reg,
> > case LTC2945_MIN_SENSE_THRES_H:
> > /*
> > * 25 uV resolution. Convert to current as measured with
> > - * an 1 mOhm sense resistor, in mA. If a different sense
> > - * resistor is installed, calculate the actual current by
> > - * dividing the reported current by the sense resistor value
> > - * in mOhm.
> > + * a 1000 microOhm sense (or shunt) resistor, in mA. If
> > + * a different shunt resistor is installed, calculate
> > + * the actual current by dividing the reported current
> > + * by the sense resistor value in microOhms. The actual
> > + * shunt resistor value can be specified in the device tree.
> > */
> > - val = DIV_ROUND_CLOSEST(val, 25);
> > + val *= shunt_resistor;
>
> Needs to ensure that there are no overflows. Try to write the maximum value
> for unsigned long and see what happens.
>
> > + val = DIV_ROUND_CLOSEST(val, 25 * 1000);
> > break;
> > default:
> > return -EINVAL;
> > @@ -234,7 +257,8 @@ static ssize_t ltc2945_value_store(struct device *dev,
> > const char *buf, size_t count)
> > {
> > struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
> > - struct regmap *regmap = dev_get_drvdata(dev);
> > + struct ltc2945_data *data = dev_get_drvdata(dev);
> > + struct regmap *regmap = data->regmap;
> > u8 reg = attr->index;
> > unsigned long val;
> > u8 regbuf[3];
> > @@ -269,7 +293,8 @@ static ssize_t ltc2945_history_store(struct device *dev,
> > const char *buf, size_t count)
> > {
> > struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
> > - struct regmap *regmap = dev_get_drvdata(dev);
> > + struct ltc2945_data *data = dev_get_drvdata(dev);
> > + struct regmap *regmap = data->regmap; > u8 reg = attr->index;
> > int num_regs = is_power_reg(reg) ? 3 : 2;
> > u8 buf_min[3] = { 0xff, 0xff, 0xff };
> > @@ -321,7 +346,8 @@ static ssize_t ltc2945_bool_show(struct device *dev,
> > struct device_attribute *da, char *buf)
> > {
> > struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
> > - struct regmap *regmap = dev_get_drvdata(dev);
> > + struct ltc2945_data *data = dev_get_drvdata(dev);
> > + struct regmap *regmap = data->regmap;
> > unsigned int fault;
> > int ret;
> >
> > @@ -450,6 +476,14 @@ static int ltc2945_probe(struct i2c_client *client)
> > struct device *dev = &client->dev;
> > struct device *hwmon_dev;
> > struct regmap *regmap;
> > + u32 shunt_resistor;
> > +
> drop this empty line
>
> > + struct ltc2945_data *data;
> > +
> > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > + dev_set_drvdata(dev, data);
> >
> > regmap = devm_regmap_init_i2c(client, &ltc2945_regmap_config);
> > if (IS_ERR(regmap)) {
> > @@ -457,11 +491,21 @@ static int ltc2945_probe(struct i2c_client *client)
> > return PTR_ERR(regmap);
> > }
> >
> > + data->regmap = regmap;
> > + if (of_property_read_u32(client->dev.of_node,
> > + "shunt-resistor-micro-ohms", &shunt_resistor))
>
> Please consider using device_property_read_u32().
>
> > + shunt_resistor = 1000; /* 1000 micro-Ohm if not set via DT */
>
> "if not set via DT" -> "default value". With device_property_read_u32(),
> this can be set by other means, not just DT.
>
> > +
> > + if (shunt_resistor == 0)
> > + return -EINVAL;
> > +
> > + data->shunt_resistor = shunt_resistor;
> > +
> > /* Clear faults */
> > regmap_write(regmap, LTC2945_FAULT, 0x00);
> >
> > hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
> > - regmap,
> > + data,
> > ltc2945_groups);
> > return PTR_ERR_OR_ZERO(hwmon_dev);
> > }
>


--
Jonathan Cormier
Software Engineer

Voice: 315.425.4045 x222



http://www.CriticalLink.com
6712 Brooklawn Parkway, Syracuse, NY 13211