Re: [next v7 0/8] Add BananaPi R3

[Lorenzo Pieralisi]

On Sun, Nov 27, 2022 at 12:41:34PM +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
> 
> This Series adds some Nodes to mt7986 devicetree and the BananaPi R3
> 
> This version is rebased on linux next from 2022/11/27.
> 
> i included sams series for mt7986 DTS with small changes
> https://patchwork.kernel.org/project/linux-mediatek/cover/20220427124741.18245->
> 
> i had run full dtbs-check but i end up with some strange warnings in
> ethernet-node that should not come up as phy-handle and sfp/managed
> properties are already defined. These errors also came up for mt7986a-rfb.
> 
> phy-handle made optional
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265
> 
> property sfp/managed (which is included for mac subnode in yaml above):
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137
> 
> changes:
> v7:
> - rebase on next so dropped already applied patches
> - squashed overlay-patch into the bpi-r3 base support
> - moved regulators from mmc-dts to common dtsi
> - changed dtsi to dts (as board base dtb) and mmc-dts to overlays
> - renamed overlays to dtso
> - removed angelos RB because of changes in bpi-r3 patch
> 
> v6:
> - dropped regulators from usb-patch as suggested by chunfeng yun
> - moved 3v3 regulator to mmc-patch as it is needed for emmc to work
>   rfbs were tested by sam shih, r3 by me
> - dropped RB from AngeloGioacchino from mmc-patch due to this change
> - fixed links in coverletter which were broken in v5
> - i hope this series is sent without errors now (my mailprovider limited
>   mails last 2 times while sending part 10)
> 
> v5:
> - changed usb ranges/reg/unit-adress
> - added reviewd-by's except usb-part due to changes
> 
> v4:
> - dropped RFC prefix
> - rebase on matthias' mtk dts-next (for 6.2) branch
> - added author information to overlays
> - fixed sfp binding error
> - added fix for moving wed_pcie node
> - readded missing compatible patches
> 
> v3:
> - changed mmc pull-ups
> - added patch for board binding (sent separately before)
> - added pcie node in mt7986 (not yet again in r3)
> - added dt overlays
> 
> Frank Wunderlich (5):
>   dt-bindings: phy: mediatek,tphy: add support for mt7986
>   dt-bindings: usb: mtk-xhci: add support for mt7986
>   dt-bindings: PCI: mediatek-gen3: add SoC based clock config
>   dt-bindings: PCI: mediatek-gen3: add support for mt7986
>   arm64: dts: mt7986: add Bananapi R3
> 
> Sam Shih (3):
>   arm64: dts: mt7986: add usb related device nodes
>   arm64: dts: mt7986: add mmc related device nodes
>   arm64: dts: mt7986: add pcie related device nodes
> 
>  .../bindings/pci/mediatek-pcie-gen3.yaml      |  64 ++-
>  .../bindings/phy/mediatek,tphy.yaml           |   1 +
>  .../bindings/usb/mediatek,mtk-xhci.yaml       |   1 +
>  arch/arm64/boot/dts/mediatek/Makefile         |   5 +
>  .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  30 ++
>  .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
>  .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 448 ++++++++++++++++++
>  arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
>  arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
>  arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
>  12 files changed, 934 insertions(+), 12 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

Should I pick up patches [3,4] into the PCI tree ?

Thanks,
Lorenzo