Re: [PATCH v8 11/11] arm64: dts: meson: a1: introduce PLL and Peripherals clk controllers

[Jerome Brunet]

On Fri 02 Dec 2022 at 01:57, Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxx> wrote:

> This patch adds clkc_periphs and clkc_pll dts nodes to A1 SoC main dtsi.
> The first one clk controller is responsible for all SoC peripherals
> clocks excluding audio clocks. The second one clk controller is used by
> A1 SoC PLLs. Actually, there are two different APB heads, so we have two
> different drivers.

Please send this change through a separate patcheset.

One patcheset/series for clk (and bindings)
Another one for the DTS (usually sent after the first one is accepted)

>
> Signed-off-by: Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 27 ++++++++++++++++++++++-
>  1 file changed, 26 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> index b4000cf65a9a..38e6517c603c 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> @@ -6,6 +6,8 @@
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/gpio/meson-a1-gpio.h>
> +#include <dt-bindings/clock/a1-pll-clkc.h>
> +#include <dt-bindings/clock/a1-clkc.h>
>  
>  / {
>  	compatible = "amlogic,a1";
> @@ -81,7 +83,6 @@ apb: bus@fe000000 {
>  			#size-cells = <2>;
>  			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x1000000>;
>  
> -
>  			reset: reset-controller@0 {
>  				compatible = "amlogic,meson-a1-reset";
>  				reg = <0x0 0x0 0x0 0x8c>;
> @@ -124,6 +125,30 @@ uart_AO_B: serial@2000 {
>  				clock-names = "xtal", "pclk", "baud";
>  				status = "disabled";
>  			};
> +
> +			clkc_periphs: periphs-clock-controller@800 {

device name should be generic so

clkc_periphs: clock-controller@800 would be better

> +				compatible = "amlogic,a1-periphs-clkc";
> +				reg = <0 0x800 0 0x104>;
> +				#clock-cells = <1>;
> +				clocks = <&clkc_pll CLKID_FCLK_DIV2>,
> +					 <&clkc_pll CLKID_FCLK_DIV3>,
> +					 <&clkc_pll CLKID_FCLK_DIV5>,
> +					 <&clkc_pll CLKID_FCLK_DIV7>,
> +					 <&clkc_pll CLKID_HIFI_PLL>,
> +					 <&xtal>;
> +				clock-names = "fclk_div2", "fclk_div3",
> +					      "fclk_div5", "fclk_div7",
> +					      "hifi_pll", "xtal";
> +			};
> +
> +			clkc_pll: pll-clock-controller@7c80 {

Same here

> +				compatible = "amlogic,a1-pll-clkc";
> +				reg = <0 0x7c80 0 0x18c>;
> +				#clock-cells = <1>;
> +				clocks = <&clkc_periphs CLKID_XTAL_FIXPLL>,
> +					 <&clkc_periphs CLKID_XTAL_HIFIPLL>;
> +				clock-names = "xtal_fixpll", "xtal_hifipll";
> +			};
>  		};
>  
>  		gic: interrupt-controller@ff901000 {