[PATCH v2 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and RP-H6B board

From: Icenowy Zheng
Date: Fri Dec 02 2022 - 03:20:47 EST


Rongpin RP-H6C is an Allwinner H6 SoM by Rongpin, with Allwinner H6 SoC,
AXP805 PMIC, LPDDR3 memory and eMMC storage on it.

RP-H6B is their official evaluation board of RP-H6C, with an onboard
GL850G USB hub, Ampak AP6212 Wi-Fi module and some circuits about LVDS
display. It also exports the OTG USB port, the USB 3.0 port, PCIe bus
(as mPCIe slot), internal Ethernet PHY, analog audio/video and HDMI
port.

Add a DTSI file for the SoM and a DTS for the full board.

Signed-off-by: Icenowy Zheng <uwu@xxxxxxxxxx>
---
Changes in v2:
- Name all regulator nodes regulator-xxx.
- Fixed underscores in node names.

arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h6-rp-h6b.dts | 239 ++++++++++++++++++
.../boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi | 180 +++++++++++++
3 files changed, 420 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6a96494a2e0a..e289fedcac29 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -36,6 +36,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-rp-h6b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
new file mode 100644
index 000000000000..d9994e9beb81
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2022 Icenowy Zheng <icenowy@xxxxxxx>
+ */
+/dts-v1/;
+
+#include "sun50i-h6-rp-h6c.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Rongpin RP-H6B baseboard";
+ compatible = "rongpin,rp-h6b", "rongpin,rp-h6c",
+ "allwinner,sun50i-h6";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ /*
+ * Prioritize the external RTC because it's powered
+ * by a cell battery.
+ */
+ rtc0 = &hym8563;
+ rtc1 = &rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi_connector: connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ label = "rongpin:red:link";
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+ /*
+ * On the schematics this LED is marked as "lit when
+ * powering on and blinking when running".
+ */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ /*
+ * The VDD_5V power rail is connected to the internal regulator
+ * of GL850G, to power up the 3.3V core of it.
+ */
+ reg_v33_hub: regulator-v33-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "v33-hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&reg_vdd_5v>;
+ };
+
+ /*
+ * This board inputs 5V to AP6212 via a SS34 diode. Use this
+ * regulator as the model of the internal regulator of AP6212.
+ */
+ reg_vcc3v3_ap6212: regulator-vcc3v3-ap6212 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3-ap6212";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&reg_ps>;
+ };
+
+ reg_vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&reg_ps>;
+ };
+
+ /* For mPCIe slot WWAN modules / PCIe cards */
+ reg_vdd_3g: regulator-vdd-3g {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-3g";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&reg_ps>;
+ /*
+ * As a hack for lacking of control of a hub downstream
+ * port's Vbus.
+ */
+ regulator-always-on;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@1 {
+ /* Genesys Logic GL850G usb hub */
+ compatible = "usb5e3,608";
+ reg = <1>;
+ vdd-supply = <&reg_v33_hub>;
+ reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <&reg_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&reg_vcc3v3_ap6212>;
+ vqmmc-supply = <&reg_bldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+/* Converted from 12v with a fixed DC-DC on the baseboard */
+&reg_ps {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+/* Bluetooth */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <1500000>;
+ clocks = <&rtc CLK_OSC32K_FANOUT>;
+ clock-names = "lpo";
+ vbat-supply = <&reg_ps>;
+ vddio-supply = <&reg_bldo3>;
+ device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+ shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+ interrupt-parent = <&r_pio>;
+ interrupts = <1 1 IRQ_TYPE_EDGE_FALLING>; /* PM1 */
+ interrupt-names = "host-wakeup";
+ };
+};
+
+&uart1_pins {
+ bias-pull-up;
+};
+
+&uart1_rts_cts_pins {
+ bias-pull-up;
+};
+
+&usb2otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy {
+ usb0_vbus-supply = <&reg_vdd_5v>;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
new file mode 100644
index 000000000000..637c194016c4
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019-2022 Icenowy Zheng <icenowy@xxxxxxx>
+ */
+
+#include "sun50i-h6.dtsi"
+#include "sun50i-h6-cpu-opp.dtsi"
+#include "sun50i-h6-gpu-opp.dtsi"
+
+/ {
+ ext_osc32k: ext-osc32k-clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
+ /* Marked 3.4v~5.5v on SoM schematics */
+ reg_ps: regulator-ps {
+ compatible = "regulator-fixed";
+ regulator-name = "ps";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdca>;
+};
+
+&gpu {
+ mali-supply = <&reg_dcdcc>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&reg_cldo1>;
+ vqmmc-supply = <&reg_bldo2>;
+ non-removable;
+ cap-mmc-hw-reset;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&pio {
+ vcc-pc-supply = <&reg_bldo2>;
+ vcc-pd-supply = <&reg_aldo2>;
+ vcc-pg-supply = <&reg_bldo3>;
+};
+
+&r_pio {
+ /*
+ * FIXME: We can't add that supply for now since it would
+ * create a circular dependency between pinctrl, the regulator
+ * and the RSB Bus.
+ *
+ * vcc-pl-supply = <&reg_aldo1>;
+ */
+ vcc-pm-supply = <&reg_bldo3>;
+};
+
+&r_rsb {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ axp805: pmic@745 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+ vina-supply = <&reg_ps>;
+ vinb-supply = <&reg_ps>;
+ vinc-supply = <&reg_ps>;
+ vind-supply = <&reg_ps>;
+ vine-supply = <&reg_ps>;
+ aldoin-supply = <&reg_ps>;
+ bldoin-supply = <&reg_ps>;
+ cldoin-supply = <&reg_ps>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ regulator-enable-ramp-delay = <100000>;
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ /* This regulator is connected with ALDO3 */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3-2";
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1160000>;
+ regulator-ramp-delay = <2500>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&rtc {
+ clocks = <&ext_osc32k>;
+};
--
2.38.1