Re: [PATCH 04/15] can: m_can: Use transmit event FIFO watermark level interrupt

From: Marc Kleine-Budde
Date: Thu Dec 01 2022 - 06:01:46 EST


On 01.12.2022 11:12:20, Markus Schneider-Pargmann wrote:
> > > For the upcoming receive side patch I already added a hrtimer. I may try
> > > to use the same timer for both directions as it is going to do the exact
> > > same thing in both cases (call the interrupt routine). Of course that
> > > depends on the details of the coalescing support. Any objections on
> > > that?
> >
> > For the mcp251xfd I implemented the RX and TX coalescing independent of
> > each other and made it configurable via ethtool's IRQ coalescing
> > options.
> >
> > The hardware doesn't support any timeouts and only FIFO not empty, FIFO
> > half full and FIFO full IRQs and the on chip RAM for mailboxes is rather
> > limited. I think the mcan core has the same limitations.
>
> Yes and no, the mcan core provides watermark levels so it has more
> options, but there is no hardware timer as well (at least I didn't see
> anything usable).

Are there any limitations to the water mark level?

> > The configuration for the mcp251xfd looks like this:
> >
> > - First decide for classical CAN or CAN-FD mode
> > - configure RX and TX ring size
> > 9263c2e92be9 ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
> > For TX only a single FIFO is used.
> > For RX up to 3 FIFOs (up to a depth of 32 each).
> > FIFO depth is limited to power of 2.
> > On the mcan cores this is currently done with a DT property.
> > Runtime configurable ring size is optional but gives more flexibility
> > for our use-cases due to limited RAM size.
> > - configure RX and TX coalescing via ethtools
> > Set a timeout and the max CAN frames to coalesce.
> > The max frames are limited to half or full FIFO.
>
> mcan can offer more options for the max frames limit fortunately.
>
> >
> > How does coalescing work?
> >
> > If coalescing is activated during reading of the RX'ed frames the FIFO
> > not empty IRQ is disabled (the half or full IRQ stays enabled). After
> > handling the RX'ed frames a hrtimer is started. In the hrtimer's
> > functions the FIFO not empty IRQ is enabled again.
>
> My rx path patches are working similarly though not 100% the same. I
> will adopt everything and add it to the next version of this series.
>
> >
> > I decided not to call the IRQ handler from the hrtimer to avoid
> > concurrency, but enable the FIFO not empty IRQ.
>
> mcan uses a threaded irq and I found this nice helper function I am
> currently using for the receive path.
> irq_wake_thread()
>
> It is not widely used so I hope this is fine. But this hopefully avoids
> the concurrency issue. Also I don't need to artificially create an IRQ
> as you do.

I think it's Ok to use the function. Which IRQs are enabled after you
leave the RX handler? The mcp251xfd driver enables only a high watermark
IRQ and sets up the hrtimer. Then we have 3 scenarios:
- high watermark IRQ triggers -> IRQ is handled,
- FIFO level between 0 and high water mark -> no IRQ triggered, but
hrtimer will run, irq_wake_thread() is called, IRQ is handled
- FIFO level 0 -> no IRQ triggered, hrtimer will run. What do you do in
the IRQ handler? Check if FIFO is empty and enable the FIFO not empty
IRQ?

The mcp251xfd unconditionally enables the FIFO not empty IRQ in the
hrtimer. This avoids reading of the FIFO fill level.

[...]

> > If you want to implement runtime configurable ring size, I created a
> > function to help in the calculation of the ring sizes:
> >
> > a1439a5add62 ("can: mcp251xfd: ram: add helper function for runtime ring size calculation")
> >
> > The code is part of the mcp251xfd driver, but is prepared to become a
> > generic helper function. The HW parameters are described with struct
> > can_ram_config and use you can_ram_get_layout() to get a valid RAM
> > layout based on CAN/CAN-FD ring size and coalescing parameters.
>
> Thank you. I think configurable ring sizes are currently out of scope
> for me as I only have limited time for this.

Ok.

regards,
Marc

--
Pengutronix e.K. | Marc Kleine-Budde |
Embedded Linux | https://www.pengutronix.de |
Vertretung West/Dortmund | Phone: +49-231-2826-924 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

Attachment: signature.asc
Description: PGP signature