Re: [PATCH v2 1/5] dt-bindings: pinctrl: Add StarFive JH7110 pinctrl definitions

From: Jianlong Huang
Date: Thu Dec 01 2022 - 04:31:10 EST


On Tue, 29 Nov 2022 15:58:12 +0100, Krzysztof Kozlowski wrote:
> On 29/11/2022 15:46, Jianlong Huang wrote:
>> On Tue, 29 Nov 2022 08:49:49 +0100, Krzysztof Kozlowski wrote:
>>> On 29/11/2022 02:47, Jianlong Huang wrote:
>>>> On Mon, 28 Nov 2022 09:32:45 +0100, Krzysztof Kozlowski wrote:
>>>>> On 28/11/2022 01:48, Jianlong Huang wrote:
>>>>>
>>>>>>>>> +/* aon_iomux doen */
>>>>>>>>> +#define GPOEN_AON_PTC0_OE_N_4 2
>>>>>>>>> +#define GPOEN_AON_PTC0_OE_N_5 3
>>>>>>>>> +#define GPOEN_AON_PTC0_OE_N_6 4
>>>>>>>>> +#define GPOEN_AON_PTC0_OE_N_7 5
>>>>>>>>> +
>>>>>>>>
>>>>>>>> It looks like you add register constants to the bindings. Why? The
>>>>>>>> bindings are not the place to represent hardware programming model. Not
>>>>>>>> mentioning that there is no benefit in this.
>>>>>>>
>>>>>>> Also: this entire file should be dropped, but if it stays, you have to
>>>>>>> name it matching bindings or compatible (vendor,device.h).
>>>>>>
>>>>>> Thanks your comments.
>>>>>> These macros are used to configure pinctrl in dts, so the file should stay,
>>>>>
>>>>> Why they should stay? What's the reason? If it is not a constant used by
>>>>> driver, then register values should not be placed in the bindings, so
>>>>> drop it.
>>>>>
>>>>
>>>> Thanks.
>>>>
>>>> These macros in binding header(example, DOUT, DOEN etc) will be used in DTS,
>>>> and driver will parse the DT for pinctrl configuration.
>>>>
>>>> Example in dts:
>>>> uart0_pins: uart0-0 {
>>>> tx-pins {
>>>> pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
>>>
>>> This is usage in DTS and is not an argument to store register
>>> addresses/offsets as bindings. What is the usage (of define, not value)
>>> in the driver?
>>>
>>
>> The existing implementation reuse the macros for DTS and driver.
>
> Where in the driver? Grep gives zero results.
>
>> Do you mean we need to separate the macros, one for DTS and one for driver usage?
>
> No, if driver uses them it is fine. The problem is I cannot find it
> anywhere.
>
>> Or you have any better suggestion?
>>
>> These macros are the value of register, not register addresses/offsets,
>> except for with prefix of GPI.
>
> Still, values are not usually part of bindings.
>
>>
>> Drivers rarely reference macros directly, mostly parsing dts and writing them to registers.
>
> So drivers do not use macros? Then there is no reason to store them in
> bindings? What do you "bind" if there is no usage (and we do not talk
> about DTS...)?
>

These macros are more friendly for configuring dts, so i stay the file.
And change the file path to 'arch/riscv/boot/dts/starfive/',
change the file name to 'jh7110-pinfunc.h'.

Best regards,
Jianlong Huang