Re: [PATCH v2 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

From: Jianlong Huang
Date: Sun Nov 27 2022 - 20:04:03 EST


On 2022/11/21 16:43, Krzysztof Kozlowski wrote:
> On 18/11/2022 02:11, Hal Feng wrote:
>> From: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>>
>> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
>>
>> Signed-off-by: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>> Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
>> ---
>> .../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 165 ++++++++++++++++++
>> 1 file changed, 165 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..79623f884a9c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> @@ -0,0 +1,165 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: StarFive JH7110 Sys Pin Controller
>> +
>> +description: |
>> + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
>> +
>> + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
>> + can be multiplexed and have configurable bias, drive strength,
>> + schmitt trigger etc.
>> + Some peripherals have their I/O go through the 64 "GPIOs". This also
>> + includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
>> + All these peripherals are connected to all 64 GPIOs such that
>> + any GPIO can be set up to be controlled by any of the peripherals.
>> +
>> +maintainers:
>> + - Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
>> +
>> +properties:
>> + compatible:
>> + const: starfive,jh7110-sys-pinctrl
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + reg-names:
>> + items:
>> + - const: control
>
> Why reg-names for one entry? Perhaps just drop it.

Will fix, drop it.

>
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + resets:
>> + maxItems: 1
>> +
>> + gpio-controller: true
>> +
>> + "#gpio-cells":
>> + const: 2
>> +
>> + interrupts:
>> + maxItems: 1
>> + description: The GPIO parent interrupt.
>
> Drop description, it's obvious.

Will fix, drop it.

>
>> +
>> + interrupt-controller: true
>> +
>> + "#interrupt-cells":
>> + const: 2
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - reg-names
>> + - clocks
>> + - gpio-controller
>> + - "#gpio-cells"
>> + - interrupts
>> + - interrupt-controller
>> + - "#interrupt-cells"
>> +
>> +patternProperties:
>> + '-[0-9]+$':
>
> Keep consistent quotes, either ' or "
>
> How do you differentiate hogs? The pattern is a bit unspecific.

Will fix.
Keep consisitent quotes, use '

>
>> + type: object
>> + patternProperties:
>> + '-pins$':
>> + type: object
>> + description: |
>> + A pinctrl node should contain at least one subnode representing the
>> + pinctrl groups available on the machine. Each subnode will list the
>> + pins it needs, and how they should be configured, with regard to
>> + muxer configuration, system signal configuration, pin groups for
>> + vin/vout module, pin voltage, mux functions for output, mux functions
>> + for output enable, mux functions for input.
>> +
>> + properties:
>> + pinmux:
>> + description: |
>> + The list of GPIOs and their mux settings that properties in the
>> + node apply to. This should be set using the GPIOMUX macro.
>> + $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux"
>
> Drop quotes.

Will fix, drop quotes.

>
>> +
>> + bias-disable: true
>> +
>> + bias-pull-up:
>> + type: boolean
>> +
>> + bias-pull-down:
>> + type: boolean
>> +
>> + drive-strength:
>> + enum: [ 2, 4, 8, 12 ]
>> +
>> + input-enable: true
>> +
>> + input-disable: true
>> +
>> + input-schmitt-enable: true
>> +
>> + input-schmitt-disable: true
>> +
>> + slew-rate:
>> + maximum: 1
>> +
>> + additionalProperties: false
>> +
>> + additionalProperties: false
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/starfive-jh7110.h>
>> + #include <dt-bindings/reset/starfive-jh7110.h>
>> + #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
>> +
>> + soc {
>
> Use 4 spaces for example indentation.

Will fix.

>
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + gpio: gpio@13040000 {
>> + compatible = "starfive,jh7110-sys-pinctrl";
>> + reg = <0x0 0x13040000 0x0 0x10000>;
>> + reg-names = "control";
>> + clocks = <&syscrg_clk JH7110_SYSCLK_IOMUX>;
>> + resets = <&syscrg_rst JH7110_SYSRST_IOMUX>;
>> + interrupts = <86>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + status = "okay";
>
> No status in examples.

Will fix, drop it.

>
>> +
>> + uart0_pins: uart0-0 {
>> + tx-pins {
>> + pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
>> + bias-disable;
>> + drive-strength = <12>;
>> + input-disable;
>> + input-schmitt-disable;
>> + slew-rate = <0>;
>> + };
>> +
>> + rx-pins {
>> + pinmux = <GPIOMUX(6, GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
>> + bias-pull-up;
>> + drive-strength = <2>;
>> + input-enable;
>> + input-schmitt-enable;
>> + slew-rate = <0>;
>> + };
>> + };
>> + };
>> +
>> + uart0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart0_pins>;
>> + status = "okay";
>
> Drop this node, useless.

Will fix, drop this node.

>
>> + };
>> + };
>> +
>> +...
>

Best regards,
Jianlong Huang