[PATCH v8 5/6] doc: Document CONFIG_RCU_CPU_STALL_CPUTIME=y stall information

From: Zhen Lei
Date: Sat Nov 19 2022 - 04:27:07 EST


This commit doucments how to quickly determine the bug causing a given
RCU CPU stall fault warning based on the output information provided
by CONFIG_RCU_CPU_STALL_CPUTIME=y.

[ paulmck: Apply wordsmithing. ]

Signed-off-by: Zhen Lei <thunder.leizhen@xxxxxxxxxx>
Signed-off-by: Paul E. McKenney <paulmck@xxxxxxxxxx>
---
Documentation/RCU/stallwarn.rst | 88 +++++++++++++++++++++++++++++++++
1 file changed, 88 insertions(+)

diff --git a/Documentation/RCU/stallwarn.rst b/Documentation/RCU/stallwarn.rst
index dfa4db8c0931eaf..c1e92dfef40d501 100644
--- a/Documentation/RCU/stallwarn.rst
+++ b/Documentation/RCU/stallwarn.rst
@@ -390,3 +390,91 @@ for example, "P3421".

It is entirely possible to see stall warnings from normal and from
expedited grace periods at about the same time during the same run.
+
+RCU_CPU_STALL_CPUTIME
+=====================
+
+In kernels built with CONFIG_RCU_CPU_STALL_CPUTIME=y or booted with
+rcupdate.rcu_cpu_stall_cputime=1, the following additional information
+is supplied with each RCU CPU stall warning::
+
+rcu: hardirqs softirqs csw/system
+rcu: number: 624 45 0
+rcu: cputime: 69 1 2425 ==> 2500(ms)
+
+These statistics are collected during the sampling period. The values
+in row "number:" are the number of hard interrupts, number of soft
+interrupts, and number of context switches on the stalled CPU. The
+first three values in row "cputime:" indicate the CPU time in
+milliseconds consumed by hard interrupts, soft interrupts, and tasks
+on the stalled CPU. The last number is the measurement interval, again
+in milliseconds. Because user-mode tasks normally do not cause RCU CPU
+stalls, these tasks are typically kernel tasks, which is why only the
+system CPU time are considered.
+
+The sampling period is shown as follows:
+:<------------first timeout---------->:<-----second timeout----->:
+:<--half timeout-->:<--half timeout-->: :
+: :<--first period-->: :
+: :<-----------second sampling period---------->:
+: : : :
+: snapshot time point 1st-stall 2nd-stall
+
+
+The following describes four typical scenarios:
+
+1. A CPU looping with interrupts disabled.::
+
+ rcu: hardirqs softirqs csw/system
+ rcu: number: 0 0 0
+ rcu: cputime: 0 0 0 ==> 2500(ms)
+
+ Because interrupts have been disabled throughout the measurement
+ interval, there are no interrupts and no context switches.
+ Furthermore, because CPU time consumption was measured using interrupt
+ handlers, the system CPU consumption is misleadingly measured as zero.
+ This scenario will normally also have "(0 ticks this GP)" printed on
+ this CPU's summary line.
+
+2. A CPU looping with bottom halves disabled.
+
+ This is similar to the previous example, but with non-zero number of
+ and CPU time consumed by hard interrupts, along with non-zero CPU
+ time consumed by in-kernel execution.::
+
+ rcu: hardirqs softirqs csw/system
+ rcu: number: 624 0 0
+ rcu: cputime: 49 0 2446 ==> 2500(ms)
+
+ The fact that there are zero softirqs gives a hint that these were
+ disabled, perhaps via local_bh_disable(). It is of course possible
+ that there were no softirqs, perhaps because all events that would
+ result in softirq execution are confined to other CPUs. In this case,
+ the diagnosis should continue as shown in the next example.
+
+3. A CPU looping with preemption disabled.
+
+ Here, only the number of context switches is zero.::
+
+ rcu: hardirqs softirqs csw/system
+ rcu: number: 624 45 0
+ rcu: cputime: 69 1 2425 ==> 2500(ms)
+
+ This situation hints that the stalled CPU was looping with preemption
+ disabled.
+
+4. No looping, but massive hard and soft interrupts.::
+
+ rcu: hardirqs softirqs csw/system
+ rcu: number: xx xx 0
+ rcu: cputime: xx xx 0 ==> 2500(ms)
+
+ Here, the number and CPU time of hard interrupts are all non-zero,
+ but the number of context switches and the in-kernel CPU time consumed
+ are zero. The number and cputime of soft interrupts will usually be
+ non-zero, but could be zero, for example, if the CPU was spinning
+ within a single hard interrupt handler.
+
+ If this type of RCU CPU stall warning can be reproduced, you can
+ narrow it down by looking at /proc/interrupts or by writing code to
+ trace each interrupt, for example, by referring to show_interrupts().
--
2.25.1