Re: [PATCH v3 4/4] arm64: dts: ti: Add support for J784S4 EVM board
From: Andrew Davis
Date: Fri Nov 18 2022 - 12:40:48 EST
On 11/16/22 7:04 AM, Apurva Nandan wrote:
J784S4 EVM board is designed for TI J784S4 SoC. It supports the following
interfaces:
* 32 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 Input Audio Jack, x1 Output Audio Jack
* x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
* x2 4L PCIe connector
* x1 UHS-1 capable micro-SD card slot
* 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
UFS flash.
* x6 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* x2 ENET Expansion Connector, x1 GESI expander, x2 Display connector
* x1 15-pin CSI header
* x6 MCAN instances
Add basic support for J784S4-EVM.
Schematics: https://www.ti.com/lit/zip/sprr458
Signed-off-by: Hari Nagalla <hnagalla@xxxxxx>
Signed-off-by: Nishanth Menon <nm@xxxxxx>
Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 197 +++++++++++++++++++++++
2 files changed, 199 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 4555a5be2257..67621b349e88 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
new file mode 100644
index 000000000000..53516fb2b346
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j784s4.dtsi"
+
+/ {
+ compatible = "ti,j784s4-evm", "ti,j784s4";
+ model = "Texas Instruments J784S4 EVM";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ aliases {
+ serial2 = &main_uart8;
This feels hacky. Your chosen node picks serial2 as that is usually
the one that is wired up on K3 boards. But on this board it is main_uart8.
So why not have this be serial10, then choose
stdout-path = "serial10:115200n8";
Also, I've made comments on previous version of this series, it is
nice to include folks who have commented before in the CC for future
versions, that way our filters don't hide these away and we can more
easily check that our comments have been addressed.
Andrew
+ mmc1 = &main_sdhci1;
+ i2c0 = &main_i2c0;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* 32G RAM */
+ reg = <0x00 0x80000000 0x00 0x80000000>,
+ <0x08 0x80000000 0x07 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ no-map;
+ };
+ };
+
+ evm_12v0: regulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: regulator-vsys3v3 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_5v0: regulator-vsys5v0 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: regulator-sd {
+ /* Output of TPS22918 */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: regulator-TLV71033 {
+ /* Output of TLV71033 */
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
+ gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+};
+
+&main_pmx0 {
+ main_uart8_pins_default: main-uart8-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
+ J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
+ J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
+ J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
+ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
+ J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
+ J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (No Pin) MMC1_CLKLB */
+ J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
+ J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
+ J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
+ J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
+ J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
+ >;
+ };
+};
+
+&main_uart8 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart8_pins_default>;
+};
+
+&main_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+
+ clock-frequency = <400000>;
+
+ exp1: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "PCIE1_2L_MODE_SEL", "PCIE1_4L_PERSTZ", "PCIE1_2L_RC_RSTZ",
+ "PCIE1_2L_EP_RST_EN", "PCIE0_4L_MODE_SEL", "PCIE0_4L_PERSTZ",
+ "PCIE0_4L_RC_RSTZ", "PCIE0_4L_EP_RST_EN", "PCIE1_4L_PRSNT#",
+ "PCIE0_4L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3",
+ "AUDIO_MUX_SEL", "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTZ";
+ };
+
+ exp2: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "R_GPIO_RGMII1_RST", "ENET2_I2CMUX_SEL", "GPIO_USD_PWR_EN",
+ "USBC_PWR_EN", "USBC_MODE_SEL1", "USBC_MODE_SEL0",
+ "GPIO_LIN_EN", "R_CAN_STB", "CTRL_PM_I2C_OE#",
+ "ENET2_EXP_PWRDN", "ENET2_EXP_SPARE2", "CDCI2_RSTZ",
+ "USB2.0_MUX_SEL", "CANUART_MUX_SEL0", "CANUART_MUX2_SEL1",
+ "CANUART_MUX1_SEL1", "ENET1_EXP_PWRDN", "ENET1_EXP_RESETZ",
+ "ENET1_I2CMUX_SEL", "ENET1_EXP_SPARE2", "ENET2_EXP_RESETZ",
+ "USER_INPUT1", "USER_LED1", "USER_LED2";
+ };
+};
+
+&main_sdhci1 {
+ /* SD card */
+ status = "okay";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ pinctrl-names = "default";
+ disable-wp;
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&main_gpio0 {
+ status = "okay";
+};