[PATCH v3 4/4] arm64: dts: rockchip: rk3566: Add SOQuartz Model A baseboard

From: Nicolas Frattaroli
Date: Wed Nov 16 2022 - 07:02:43 EST


From: Andrew Powers-Holmes <aholmes@xxxxxxxxx>

This patch adds the device tree for the "Model A" baseboard for
the SOQuartz CM4 SoM, which is not to be confused with the
Quartz64 Model A, which is the same form factor and SoC, but is
not a CM4 carrier board.

The board features a PCIe 2 x1 slot, USB 2 host ports, CSI/DSI
connectors, an eDP FFC connector, gigabit ethernet, HDMI, and a
12V DC barrel jack. Also present is a microSD card slot, 40-pin
GPIO, and a power and reset button.

Signed-off-by: Andrew Powers-Holmes <aholmes@xxxxxxxxx>
[rebase, misc fixes, reword]
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@xxxxxxxxx>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3566-soquartz-model-a.dts | 232 ++++++++++++++++++
2 files changed, 233 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 528a02b11552..f78c0a935bce 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-blade.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-model-a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-box-demo.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts
new file mode 100644
index 000000000000..2208dbfb7f0a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-model-a.dts
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+ model = "PINE64 RK3566 SOQuartz on Model A carrier board";
+ compatible = "pine64,soquartz-model-a", "pine64,soquartz", "rockchip,rk3566";
+
+ /* labeled DCIN_12V in schematic */
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ /*
+ * Labelled VCC3V0_SD in schematic to not conflict with PMIC
+ * regulator, it's 3.3v in actuality
+ */
+ vcc3v0_sd: vcc3v0-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v0_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_pcie: vcc3v3-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc12v_pcie: vcc12v-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_pcie";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+/* phy for pcie */
+&combphy2 {
+ phy-supply = <&vcc3v3_sys>;
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "okay";
+
+ /*
+ * the rtc interrupt is tied to PMIC_PWRON,
+ * it will force reset the board if triggered.
+ */
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063";
+ reg = <0x51>;
+ };
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+ status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6 - i2s1_sdi2_m1
+ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+&led_diy {
+ status = "okay";
+};
+
+&led_work {
+ status = "okay";
+};
+
+&pcie2x1 {
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+ status = "disabled";
+};
+
+/*
+ * vmmc-supply is vcc3v3_sd on v1.0 and vcc3v0_sd on v1.1+
+ * the soquartz SoM has SDMMC_PWR (CM1 pin 75) hardwired to vcc3v3_sys,
+ * so we use vcc3v3_sd here to ensure the regulator is enabled on older boards.
+ */
+&sdmmc0 {
+ vmmc-supply = <&vcc3v3_sd>;
+ status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7 - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8 - spi3_cs0_m0
+ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&vbus {
+ vin-supply = <&vcc5v0_usb>;
+};
+
+&vcc3v3_sd {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ status = "okay";
+};
--
2.38.1