Re: [PATCH v3 2/2] rtc: ds1307: Add support for Epson RX8111

[Alexandre Belloni]

I should have commented on this patch but my comment is still valid,
even more so that the alarm handling is bloating the driver.

On 07/11/2022 09:54:08+0100, Mike Looijmans wrote:
> The rx_8111 is quite similar to the rx_8030. This adds support for this
> chip to the ds1307 driver. Date/time and alarm registers are in the
> usual places. The nvmem is located at 0x40. Time stamping is not
> supported.
> 
> Signed-off-by: Mike Looijmans <mike.looijmans@xxxxxxxx>
> 
> ---
> 
> Changes in v3:
> Wrong version of code sent in v2
> Attempt to fix e-mail sending issues
> 
> Changes in v2:
> Add "_REG" in register names
> Add interrupt/alarm handling (different from rx8030)
> 
>  drivers/rtc/rtc-ds1307.c | 306 ++++++++++++++++++++++++++++++++++++---
>  1 file changed, 284 insertions(+), 22 deletions(-)
> 
> diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
> index d51565bcc189..5aeb5732bae5 100644
> --- a/drivers/rtc/rtc-ds1307.c
> +++ b/drivers/rtc/rtc-ds1307.c
> @@ -46,6 +46,7 @@ enum ds_type {
>  	m41t11,
>  	mcp794xx,
>  	rx_8025,
> +	rx_8111,
>  	rx_8130,
>  	last_ds_type /* always last */
>  	/* rs5c372 too?  different address... */
> @@ -113,6 +114,24 @@ enum ds_type {
>  #	define RX8025_BIT_VDET		0x40
>  #	define RX8025_BIT_XST		0x20
>  
> +#define RX8111_REG_EXTENSION	0x1d
> +#	define RX8111_REG_EXTENSION_WADA	BIT(3)
> +#define RX8111_REG_FLAG		0x1e
> +#	define RX8111_REG_FLAG_VLF	BIT(1)
> +#	define RX8111_REG_FLAG_EVF	BIT(2)
> +#	define RX8111_REG_FLAG_AF	BIT(3)
> +#	define RX8111_REG_FLAG_TF	BIT(4)
> +#	define RX8111_REG_FLAG_UF	BIT(5)
> +#define RX8111_REG_CONTROL	0x1e
> +#	define RX8111_REG_CONTROL_EIE	BIT(2)
> +#	define RX8111_REG_CONTROL_AIE	BIT(3)
> +#	define RX8111_REG_CONTROL_TIE	BIT(4)
> +#	define RX8111_REG_CONTROL_UIE	BIT(5)
> +#define RX8111_REG_PWR_SWITCH_CTRL	0x32
> +#	define RX8111_PSC_SMP_INIEN	BIT(6)
> +#	define RX8111_PSC_SMP_CHGEN	BIT(7)
> +#define RX8111_REG_TIME_STAMP_BUF_CTRL	0x34
> +
>  #define RX8130_REG_ALARM_MIN		0x17
>  #define RX8130_REG_ALARM_HOUR		0x18
>  #define RX8130_REG_ALARM_WEEK_OR_DAY	0x19
> @@ -205,6 +224,68 @@ struct chip_desc {
>  
>  static const struct chip_desc chips[last_ds_type];
>  
> +static int ds1307_check_voltage_lost(struct ds1307 *ds1307)
> +{
> +	int ret;
> +	unsigned int reg;
> +	unsigned int mask;
> +	unsigned int regflag;
> +
> +	switch (ds1307->type) {
> +	case rx_8111:
> +		reg = RX8111_REG_FLAG;
> +		mask = RX8111_REG_FLAG_VLF;
> +		break;
> +	case rx_8130:
> +		reg = RX8130_REG_FLAG;
> +		mask = RX8130_REG_FLAG_VLF;
> +		break;
> +	default:
> +		return 0;
> +	}
> +
> +	ret = regmap_read(ds1307->regmap, reg, &regflag);
> +	if (ret) {
> +		dev_err(ds1307->dev, "%s error %d\n", "read", ret);
> +		return ret;
> +	}
> +
> +	if (regflag & mask) {
> +		dev_warn_once(ds1307->dev, "oscillator failed, set time!\n");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int ds1307_clear_voltage_lost(struct ds1307 *ds1307)
> +{
> +	int ret;
> +	unsigned int reg;
> +	unsigned int mask;
> +
> +	switch (ds1307->type) {
> +	case rx_8111:
> +		reg = RX8111_REG_FLAG;
> +		mask = (unsigned int)~RX8111_REG_FLAG_VLF;
> +		break;
> +	case rx_8130:
> +		reg = RX8130_REG_FLAG;
> +		mask = (unsigned int)~RX8130_REG_FLAG_VLF;
> +		break;
> +	default:
> +		return 0;
> +	}
> +
> +	ret = regmap_write(ds1307->regmap, reg, mask);
> +	if (ret) {
> +		dev_err(ds1307->dev, "%s error %d\n", "write", ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
>  static int ds1307_get_time(struct device *dev, struct rtc_time *t)
>  {
>  	struct ds1307	*ds1307 = dev_get_drvdata(dev);
> @@ -212,19 +293,9 @@ static int ds1307_get_time(struct device *dev, struct rtc_time *t)
>  	const struct chip_desc *chip = &chips[ds1307->type];
>  	u8 regs[7];
>  
> -	if (ds1307->type == rx_8130) {
> -		unsigned int regflag;
> -		ret = regmap_read(ds1307->regmap, RX8130_REG_FLAG, &regflag);
> -		if (ret) {
> -			dev_err(dev, "%s error %d\n", "read", ret);
> -			return ret;
> -		}
> -
> -		if (regflag & RX8130_REG_FLAG_VLF) {
> -			dev_warn_once(dev, "oscillator failed, set time!\n");
> -			return -EINVAL;
> -		}
> -	}
> +	ret = ds1307_check_voltage_lost(ds1307);
> +	if (ret)
> +		return ret;
>  
>  	/* read the RTC date and time registers all at once */
>  	ret = regmap_bulk_read(ds1307->regmap, chip->offset, regs,
> @@ -397,15 +468,9 @@ static int ds1307_set_time(struct device *dev, struct rtc_time *t)
>  		return result;
>  	}
>  
> -	if (ds1307->type == rx_8130) {
> -		/* clear Voltage Loss Flag as data is available now */
> -		result = regmap_write(ds1307->regmap, RX8130_REG_FLAG,
> -				      ~(u8)RX8130_REG_FLAG_VLF);
> -		if (result) {
> -			dev_err(dev, "%s error %d\n", "write", result);
> -			return result;
> -		}
> -	}
> +	result =  ds1307_clear_voltage_lost(ds1307);
> +	if (result)
> +		return result;
>  
>  	return 0;
>  }
> @@ -541,6 +606,174 @@ static u8 do_trickle_setup_ds1339(struct ds1307 *ds1307, u32 ohms, bool diode)
>  	return setup;
>  }
>  
> +static u8 do_trickle_setup_rx8111(struct ds1307 *ds1307, u32 ohms, bool diode)
> +{
> +	/* make sure that the backup battery is enabled */
> +	u8 setup = RX8111_PSC_SMP_INIEN;
> +
> +	if (diode)
> +		setup |= RX8111_PSC_SMP_CHGEN;
> +
> +	return setup;
> +}
> +
> +static irqreturn_t rx8111_irq(int irq, void *dev_id)
> +{
> +	struct ds1307 *ds1307 = dev_id;
> +	irqreturn_t result = IRQ_NONE;
> +	int ret;
> +	u8 ctl[2];
> +	u8 flags = 0;
> +
> +	rtc_lock(ds1307->rtc);
> +
> +	/* Read flag and control registers. */
> +	ret = regmap_bulk_read(ds1307->regmap, RX8111_REG_FLAG, ctl,
> +			       sizeof(ctl));
> +	if (ret < 0)
> +		goto out;
> +
> +	if (ctl[0] & RX8111_REG_FLAG_AF) {
> +		result = IRQ_HANDLED;
> +		flags |= RTC_AF; /* Alarm */
> +		ctl[1] &= ~RX8111_REG_CONTROL_AIE;
> +	}
> +	/*
> +	 * If an interrupt occurred that we cannot process, we'll have to turn
> +	 * it off, otherwise we'd be called again and again.
> +	 */
> +	if (ctl[0] & RX8111_REG_FLAG_UF) {
> +		result = IRQ_HANDLED;
> +		ctl[1] &= ~RX8111_REG_CONTROL_UIE;
> +	}
> +	if (ctl[0] & RX8111_REG_FLAG_TF) {
> +		result = IRQ_HANDLED;
> +		ctl[1] &= ~RX8111_REG_CONTROL_TIE;
> +	}
> +	if (ctl[0] & RX8111_REG_FLAG_EVF) {
> +		result = IRQ_HANDLED;
> +		ctl[1] &= ~RX8111_REG_CONTROL_EIE;
> +	}
> +	/* Clear all flags */
> +	ctl[0] &= ~(RX8111_REG_FLAG_UF | RX8111_REG_FLAG_TF |
> +		    RX8111_REG_FLAG_AF | RX8111_REG_FLAG_EVF);
> +
> +	ret = regmap_bulk_write(ds1307->regmap, RX8111_REG_FLAG, ctl,
> +				sizeof(ctl));
> +	if (ret < 0)
> +		goto out;
> +
> +	rtc_update_irq(ds1307->rtc, 1, flags | RTC_IRQF);
> +
> +out:
> +	rtc_unlock(ds1307->rtc);
> +
> +	return result;
> +}
> +
> +static int rx8111_read_alarm(struct device *dev, struct rtc_wkalrm *t)
> +{
> +	struct ds1307 *ds1307 = dev_get_drvdata(dev);
> +	u8 ald[3], ctl[2];
> +	int ret;
> +
> +	/* Read alarm registers. */
> +	ret = regmap_bulk_read(ds1307->regmap, RX8130_REG_ALARM_MIN, ald,
> +			       sizeof(ald));
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Read flag and control registers. */
> +	ret = regmap_bulk_read(ds1307->regmap, RX8111_REG_FLAG, ctl,
> +			       sizeof(ctl));
> +	if (ret < 0)
> +		return ret;
> +
> +	t->enabled = !!(ctl[1] & RX8111_REG_CONTROL_AIE);
> +	t->pending = !!(ctl[0] & RX8111_REG_FLAG_AF);
> +
> +	/* Report alarm 0 time assuming 24-hour and day-of-month modes. */
> +	t->time.tm_sec = -1;
> +	t->time.tm_min = bcd2bin(ald[0] & 0x7f);
> +	t->time.tm_hour = bcd2bin(ald[1] & 0x7f);
> +	t->time.tm_wday = -1;
> +	t->time.tm_mday = bcd2bin(ald[2] & 0x7f);
> +	t->time.tm_mon = -1;
> +	t->time.tm_year = -1;
> +	t->time.tm_yday = -1;
> +	t->time.tm_isdst = -1;
> +
> +	dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d enabled=%d\n",
> +		__func__, t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
> +		t->time.tm_wday, t->time.tm_mday, t->time.tm_mon, t->enabled);

%ptR ?

> +
> +	return 0;
> +}
> +
> +static int rx8111_set_alarm(struct device *dev, struct rtc_wkalrm *t)
> +{
> +	struct ds1307 *ds1307 = dev_get_drvdata(dev);
> +	u8 ald[3], ctl[3];
> +	int ret;
> +
> +	dev_dbg(dev, "%s, sec=%d min=%d hour=%d wday=%d mday=%d mon=%d "
> +		"enabled=%d pending=%d\n", __func__,
> +		t->time.tm_sec, t->time.tm_min, t->time.tm_hour,
> +		t->time.tm_wday, t->time.tm_mday, t->time.tm_mon,
> +		t->enabled, t->pending);
> +
%ptR ?

Is that even useful as there is already a tracepoint that is always
available?

> +	/* Read control registers. */
> +	ret = regmap_bulk_read(ds1307->regmap, RX8111_REG_EXTENSION, ctl,
> +			       sizeof(ctl));
> +	if (ret < 0)
> +		return ret;
> +
> +	ctl[0] &= RX8111_REG_EXTENSION_WADA;
> +	ctl[1] &= ~RX8111_REG_FLAG_AF;
> +	ctl[2] &= ~RX8111_REG_CONTROL_AIE;
> +
> +	ret = regmap_bulk_write(ds1307->regmap, RX8111_REG_EXTENSION, ctl,
> +				sizeof(ctl));
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Hardware alarm precision is 1 minute! */

Instead of a comment here, you should set rtc->features properly

> +	ald[0] = bin2bcd(t->time.tm_min);
> +	ald[1] = bin2bcd(t->time.tm_hour);
> +	ald[2] = bin2bcd(t->time.tm_mday);
> +
> +	ret = regmap_bulk_write(ds1307->regmap, RX8130_REG_ALARM_MIN, ald,
> +				sizeof(ald));
> +	if (ret < 0)
> +		return ret;
> +
> +	if (!t->enabled)
> +		return 0;
> +
> +	ctl[2] |= RX8111_REG_CONTROL_AIE;
> +
> +	return regmap_write(ds1307->regmap, RX8111_REG_CONTROL, ctl[2]);
> +}
> +
> +static int rx8111_alarm_irq_enable(struct device *dev, unsigned int enabled)
> +{
> +	struct ds1307 *ds1307 = dev_get_drvdata(dev);
> +	int ret, reg;
> +
> +	ret = regmap_read(ds1307->regmap, RX8111_REG_CONTROL, &reg);
> +	if (ret < 0)
> +		return ret;
> +
> +	if (enabled)
> +		reg |= RX8111_REG_CONTROL_AIE;
> +	else
> +		reg &= ~RX8111_REG_CONTROL_AIE;
> +
> +	dev_dbg(dev, "%s, enable=%u, reg=0x%x\n", __func__, enabled, reg);
> +
> +	return regmap_write(ds1307->regmap, RX8111_REG_CONTROL, reg);
> +}
> +
>  static u8 do_trickle_setup_rx8130(struct ds1307 *ds1307, u32 ohms, bool diode)
>  {
>  	/* make sure that the backup battery is enabled */
> @@ -943,6 +1176,14 @@ static const struct rtc_class_ops rx8130_rtc_ops = {
>  	.alarm_irq_enable = rx8130_alarm_irq_enable,
>  };
>  
> +static const struct rtc_class_ops rx8111_rtc_ops = {
> +	.read_time      = ds1307_get_time,
> +	.set_time       = ds1307_set_time,
> +	.read_alarm     = rx8111_read_alarm,
> +	.set_alarm      = rx8111_set_alarm,
> +	.alarm_irq_enable = rx8111_alarm_irq_enable,
> +};
> +
>  static const struct rtc_class_ops mcp794xx_rtc_ops = {
>  	.read_time      = ds1307_get_time,
>  	.set_time       = ds1307_set_time,
> @@ -1012,6 +1253,16 @@ static const struct chip_desc chips[last_ds_type] = {
>  		.century_bit	= DS1337_BIT_CENTURY,
>  		.bbsqi_bit	= DS3231_BIT_BBSQW,
>  	},
> +	[rx_8111] = {
> +		.alarm		= 1,
> +		.nvram_offset	= 0x40,
> +		.nvram_size	= 0x40,	/* 0x40 .. 0x7F is user RAM */
> +		.offset		= 0x10,
> +		.irq_handler = rx8111_irq,
> +		.rtc_ops = &rx8111_rtc_ops,
> +		.trickle_charger_reg = RX8111_REG_PWR_SWITCH_CTRL,
> +		.do_trickle_setup = &do_trickle_setup_rx8111,
> +	},
>  	[rx_8130] = {
>  		.alarm		= 1,
>  		/* this is battery backed SRAM */
> @@ -1063,6 +1314,7 @@ static const struct i2c_device_id ds1307_id[] = {
>  	{ "pt7c4338", ds_1307 },
>  	{ "rx8025", rx_8025 },
>  	{ "isl12057", ds_1337 },
> +	{ "rx8111", rx_8111 },
>  	{ "rx8130", rx_8130 },
>  	{ }
>  };
> @@ -1137,6 +1389,10 @@ static const struct of_device_id ds1307_of_match[] = {
>  		.compatible = "isil,isl12057",
>  		.data = (void *)ds_1337
>  	},
> +	{
> +		.compatible = "epson,rx8111",
> +		.data = (void *)rx_8111
> +	},
>  	{
>  		.compatible = "epson,rx8130",
>  		.data = (void *)rx_8130
> @@ -1880,6 +2136,12 @@ static int ds1307_probe(struct i2c_client *client,
>  				     DS1307_REG_HOUR << 4 | 0x08, hour);
>  		}
>  		break;
> +	case rx_8111:
> +		/* Use memory as user RAM */
> +		regmap_write(ds1307->regmap, RX8111_REG_TIME_STAMP_BUF_CTRL, 0);
> +		/* Disable timer, events, frequency output */
> +		regmap_write(ds1307->regmap, RX8111_REG_EXTENSION, 0xc8);
> +		break;
>  	case ds_1388:
>  		err = regmap_read(ds1307->regmap, DS1388_REG_CONTROL, &tmp);
>  		if (err) {
> -- 
> 2.17.1
> 

-- 
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com