Re: [PATCH] ARM: dts: Update Nanobone DTS

[Krzysztof Kozlowski]

On 09/11/2022 15:30, Mark Jackson wrote:
> Update Nanobone DTS file as follows:-

Drop trailing dash.

Use subject prefixes matching the subsystem (git log --oneline -- ...).

> - Fix GPIO settings for RTS/CTS pins on UART3 & 4
> - Enable RS485 mode for UART3 & 4
> - Enable LM75 temperature sensor
> - Fix GPIO settings for MMC pins
> - Enable USB

Split patch per logical changes so your subject summarizes the change,
not just "update".

Missing Signed-off-by, so you also did not run checkpatch. Please run
scripts/checkpatch.pl and fix reported warnings.

> ---
>  arch/arm/boot/dts/am335x-nano.dts | 33 +++++++++++++++++++++++++------
>  1 file changed, 27 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts
> index b6f2567bd65a..1f613e879c53 100644
> --- a/arch/arm/boot/dts/am335x-nano.dts
> +++ b/arch/arm/boot/dts/am335x-nano.dts
> @@ -120,8 +120,8 @@ AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE1)		/* spi0_d0.uart2_txd
>  
>  	uart3_pins: uart3_pins {
>  		pinctrl-single,pins = <
> -			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_INPUT_PULLUP, MUX_MODE6)	/* lcd_data10.uart3_ctsn */
> -			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE6)		/* lcd_data11.uart3_rtsn */
> +			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_INPUT_PULLUP, MUX_MODE7)	/* lcd_data10.gpio2[16] */
> +			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE7)		/* lcd_data11.gpio2[17] */
>  			AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE1)		/* spi0_cs1.uart3_rxd */
>  			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_OUTPUT, MUX_MODE1)		/* ecap0_in_pwm0_out.uart3_txd */
>  		>;
> @@ -129,8 +129,8 @@ AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_OUTPUT, MUX_MODE1)		/* ecap0_in
>  
>  	uart4_pins: uart4_pins {
>  		pinctrl-single,pins = <
> -			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT_PULLUP, MUX_MODE6)	/* lcd_data12.uart4_ctsn */
> -			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE6)		/* lcd_data13.uart4_rtsn */
> +			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT_PULLUP, MUX_MODE7)	/* lcd_data12.gpio0[8] */
> +			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE7)		/* lcd_data13.gpio0[9] */
>  			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE1)		/* uart0_ctsn.uart4_rxd */
>  			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_OUTPUT, MUX_MODE1)		/* uart0_rtsn.uart4_txd */
>  		>;
> @@ -188,12 +188,22 @@ &uart3 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart3_pins>;
>  	status = "okay";

Status is the last property.

> +	rts-gpio = <&gpio2 17 GPIO_ACTIVE_HIGH>;
> +	rs485-rts-active-high;
> +	rs485-rx-during-tx;
> +	rs485-rts-delay = <1 1>;
> +	linux,rs485-enabled-at-boot-time;
>  };
>  
>  &uart4 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart4_pins>;
>  	status = "okay";

Ditto

> +	rts-gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
> +	rs485-rts-active-high;
> +	rs485-rx-during-tx;
> +	rs485-rts-delay = <1 1>;
> +	linux,rs485-enabled-at-boot-time;
>  };
>  
>  &uart5 {
> @@ -220,6 +230,12 @@ tps: tps@24 {
>  		reg = <0x24>;
>  	};
>  
> +	lm75@48 {

Generic node names, so probably "temperature-sensor". Check existing
sources.

> +		compatible = "lm75";
> +		reg = <0x48>;
> +		status = "okay";

No need, drop.


Best regards,
Krzysztof