Re: [PATCH] dt-bindings: pinctrl: qcom,msm8976: convert to dtschema

[Marijn Suijten]

On 2022-11-08 15:09:09, Krzysztof Kozlowski wrote:
> Convert Qualcomm MSM8976 pin controller bindings to DT schema.  Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
> 
> Changes during conversion: update the list of non-mux pins (like sdc1)
> to match Linux driver.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>

Thanks for sending this right as we are upstreaming MSM8976!  With one
question and one nit below:

Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>

> ---
>  .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 ------------------
>  .../pinctrl/qcom,msm8976-pinctrl.yaml         | 137 +++++++++++++
>  2 files changed, 137 insertions(+), 183 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> deleted file mode 100644
> index 70d04d12f136..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> +++ /dev/null
> @@ -1,183 +0,0 @@
> -Qualcomm MSM8976 TLMM block
> -
> -This binding describes the Top Level Mode Multiplexer block found in the
> -MSM8956 and MSM8976 platforms.
> -
> -- compatible:
> -	Usage: required
> -	Value type: <string>
> -	Definition: must be "qcom,msm8976-pinctrl"
> -
> -- reg:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: the base address and size of the TLMM register space.
> -
> -- interrupts:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: should specify the TLMM summary IRQ.
> -
> -- interrupt-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as an interrupt controller
> -
> -- #interrupt-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/interrupt-controller/irq.h>
> -
> -- gpio-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as a gpio controller
> -
> -- #gpio-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/gpio/gpio.h>
> -
> -- gpio-ranges:
> -	Usage: required
> -	Definition:  see ../gpio/gpio.txt
> -
> -- gpio-reserved-ranges:
> -	Usage: optional
> -	Definition: see ../gpio/gpio.txt
> -
> -Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> -a general description of GPIO and interrupt bindings.
> -
> -Please refer to pinctrl-bindings.txt in this directory for details of the
> -common pinctrl bindings used by client devices, including the meaning of the
> -phrase "pin configuration node".
> -
> -The pin configuration nodes act as a container for an arbitrary number of
> -subnodes. Each of these subnodes represents some desired configuration for a
> -pin, a group, or a list of pins or groups. This configuration can include the
> -mux function to select on those pin(s)/group(s), and various pin configuration
> -parameters, such as pull-up, drive strength, etc.
> -
> -
> -PIN CONFIGURATION NODES:
> -
> -The name of each subnode is not important; all subnodes should be enumerated
> -and processed purely based on their content.
> -
> -Each subnode only affects those parameters that are explicitly listed. In
> -other words, a subnode that lists a mux function but no pin configuration
> -parameters implies no information about any pin configuration parameters.
> -Similarly, a pin subnode that describes a pullup parameter implies no
> -information about e.g. the mux function.
> -
> -
> -The following generic properties as defined in pinctrl-bindings.txt are valid
> -to specify in a pin configuration subnode:
> -
> -- pins:
> -	Usage: required
> -	Value type: <string-array>
> -	Definition: List of gpio pins affected by the properties specified in
> -		    this subnode.
> -
> -		    Valid pins are:
> -		      gpio0-gpio145
> -		        Supports mux, bias and drive-strength
> -
> -		      sdc1_clk, sdc1_cmd, sdc1_data,
> -		      sdc2_clk, sdc2_cmd, sdc2_data,
> -		      sdc3_clk, sdc3_cmd, sdc3_data
> -		        Supports bias and drive-strength
> -
> -- function:
> -	Usage: required
> -	Value type: <string>
> -	Definition: Specify the alternative function to be configured for the
> -		    specified pins. Functions are only valid for gpio pins.
> -		    Valid values are:
> -
> -		    gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
> -		    blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
> -		    qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
> -		    blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
> -		    qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
> -		    qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
> -		    blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
> -		    sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
> -		    blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
> -		    uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
> -		    uim1_present, uim2_data, uim2_clk, uim2_reset,
> -		    uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout,
> -		    ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset,
> -		    cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c,
> -		    lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1,
> -		    codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1,
> -		    wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot,
> -		    key_focus, key_home, pwr_down, dmic0_clk, hdmi_int,
> -		    dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8,
> -		    pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx,
> -		    sdcard_det, sec_mi2s, ss_switch,
> -
> -- bias-disable:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as no pull.
> -
> -- bias-pull-down:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull down.
> -
> -- bias-pull-up:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull up.
> -
> -- output-high:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    high.
> -		    Not valid for sdc pins.
> -
> -- output-low:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    low.
> -		    Not valid for sdc pins.
> -
> -- drive-strength:
> -	Usage: optional
> -	Value type: <u32>
> -	Definition: Selects the drive strength for the specified pins, in mA.
> -		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> -
> -Example:
> -
> -	tlmm: pinctrl@1000000 {
> -		compatible = "qcom,msm8976-pinctrl";
> -		reg = <0x1000000 0x300000>;
> -		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> -		gpio-controller;
> -		#gpio-cells = <2>;
> -		gpio-ranges = <&tlmm 0 0 145>;
> -		interrupt-controller;
> -		#interrupt-cells = <2>;
> -
> -		blsp1_uart2_active: blsp1_uart2_active {
> -			mux {
> -				pins = "gpio4", "gpio5", "gpio6", "gpio7";
> -				function = "blsp_uart2";
> -			};
> -
> -			config {
> -				pins = "gpio4", "gpio5", "gpio6", "gpio7";
> -				drive-strength = <2>;
> -				bias-disable;
> -			};
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml
> new file mode 100644
> index 000000000000..1002a57248f6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml
> @@ -0,0 +1,137 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,msm8976-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm MSM8976 TLMM pin controller
> +
> +maintainers:
> +  - Bjorn Andersson <andersson@xxxxxxxxxx>
> +  - Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> +
> +description:
> +  Top Level Mode Multiplexer pin controller in Qualcomm MSM8976 SoC.
> +
> +properties:
> +  compatible:
> +    const: qcom,msm8976-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts: true
> +  interrupt-controller: true
> +  "#interrupt-cells": true
> +  gpio-controller: true
> +  "#gpio-cells": true
> +  gpio-ranges: true
> +  wakeup-parent: true
> +
> +  gpio-reserved-ranges:
> +    minItems: 1
> +    maxItems: 73
> +
> +  gpio-line-names:
> +    maxItems: 145
> +
> +patternProperties:
> +  "-state$":
> +    oneOf:
> +      - $ref: "#/$defs/qcom-msm8976-tlmm-state"
> +      - patternProperties:
> +          "-pins$":
> +            $ref: "#/$defs/qcom-msm8976-tlmm-state"
> +        additionalProperties: false
> +
> +$defs:
> +  qcom-msm8976-tlmm-state:
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.

I thought I read earlier that the description shouldn't describe the DT
format: should this be `state` instead of `subnode` (same in the
description above)?

> +        items:
> +          oneOf:
> +            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-3][0-9]|14[0-4])$"
> +            - enum: [ qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
> +                      qdsd_data3 sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk,
> +                      sdc2_clk, sdc2_cmd, sdc2_data ]
> +        minItems: 1
> +        maxItems: 36
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +
> +        enum: [ gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
> +                blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
> +                qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
> +                blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
> +                qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
> +                qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
> +                blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
> +                sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
> +                blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
> +                uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
> +                uim1_present, uim2_data, uim2_clk, uim2_reset, uim2_present,
> +                ts_xvdd, mipi_dsi0, us_euro, ts_resout, ts_sample,
> +                sec_mi2s_mclk_b, pri_mi2s, codec_reset, cdc_pdm0, us_emitter,
> +                pri_mi2s_mclk_b, pri_mi2s_mclk_c, lpass_slimbus,
> +                lpass_slimbus0, lpass_slimbus1, codec_int1, codec_int2,
> +                wcss_bt, sdc3, wcss_wlan2, wcss_wlan1, wcss_wlan0, wcss_wlan,
> +                wcss_fm, key_volp, key_snapshot, key_focus, key_home, pwr_down,
> +                dmic0_clk, hdmi_int, dmic0_data, wsa_vi, wsa_en, blsp_spi8,
> +                wsa_irq, blsp_i2c8, pa_indicator, modem_tsync, ssbi_wtr1,
> +                gsm1_tx, gsm0_tx, sdcard_det, sec_mi2s, ss_switch ]
> +
> +      bias-pull-down: true
> +      bias-pull-up: true
> +      bias-disable: true
> +      drive-strength: true
> +      input-enable: true
> +      output-high: true
> +      output-low: true
> +
> +    required:
> +      - pins
> +
> +    additionalProperties: false
> +
> +allOf:
> +  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    tlmm: pinctrl@1000000 {
> +        compatible = "qcom,msm8976-pinctrl";
> +        reg = <0x1000000 0x300000>;
> +        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +        gpio-controller;
> +        #gpio-cells = <2>;
> +        gpio-ranges = <&tlmm 0 0 145>;

Shouldn't this be alphabetical (disregarding `#`), where cells <
controller? (same for interrupt-controller below)

- Marijn

> +        interrupt-controller;
> +        #interrupt-cells = <2>;
> +
> +        blsp1-uart2-active-state {
> +            pins = "gpio4", "gpio5", "gpio6", "gpio7";
> +            function = "blsp_uart2";
> +            drive-strength = <2>;
> +            bias-disable;
> +        };
> +    };
> -- 
> 2.34.1
>