[PATCH v5 0/6] Nuvoton WPCM450 clock and reset driver

[Jonathan Neuschäfer]

This series adds support for the clock and reset controller in the Nuvoton
WPCM450 SoC. This means that the clock rates for peripherals will be calculated
automatically based on the clock tree as it was preconfigured by the bootloader.
The 24 MHz dummy clock, that is currently in the devicetree, is no longer needed.
Somewhat unfortunately, this also means that there is a breaking change once
the devicetree starts relying on the clock driver, but I find it acceptable in
this case, because WPCM450 is still at a somewhat early stage.


Upstreaming plan (although other suggestions are welcome):

Once reviewed,

- The ARM/dts changes should go through Joel Stanley's bmc tree
- The clocksource/timer changes should probably go via Daniel Lezcano and TIP
- The clock controller bindings and driver should go through the clk tree
- It probably makes sense to delay the final ARM/dts patch ("ARM: dts:
  wpcm450: Switch clocks to clock controller") until next cycle to make
  sure it is merged after the clock driver.


v5:
- Dropped patch 2 (watchdog: npcm: Enable clock if provided), which
  was since merged upstream
- Added patch 2 (clocksource: timer-npcm7xx: Enable timer 1 clock before use) again,
  because I wasn't able to find it in linux-next
- Switched the driver to using struct clk_parent_data
- Rebased on 6.1-rc3

v4:
- https://lore.kernel.org/lkml/20220610072141.347795-1-j.neuschaefer@xxxxxxx/
- Leave WDT clock running during after restart handler
- Fix reset controller initialization
- Dropped patch 2/7 (clocksource: timer-npcm7xx: Enable timer 1 clock before use),
  as it was applied by Daniel Lezcano

v3:
- https://lore.kernel.org/lkml/20220508194333.2170161-1-j.neuschaefer@xxxxxxx/
- Changed "refclk" string to "ref"
- Fixed some dead code in the driver
- Added clk_prepare_enable call to the watchdog restart handler
- Added a few review tags

v2:
- https://lore.kernel.org/lkml/20220429172030.398011-1-j.neuschaefer@xxxxxxx/
- various small improvements

v1:
- https://lore.kernel.org/lkml/20220422183012.444674-1-j.neuschaefer@xxxxxxx/

Jonathan Neuschäfer (6):
  dt-bindings: timer: nuvoton,npcm7xx-timer: Allow specifying all clocks
  clocksource: timer-npcm7xx: Enable timer 1 clock before use
  dt-bindings: clock: Add Nuvoton WPCM450 clock/reset controller
  ARM: dts: wpcm450: Add clock controller node
  clk: wpcm450: Add Nuvoton WPCM450 clock/reset controller driver
  [NOT FOR MERGE] ARM: dts: wpcm450: Switch clocks to clock controller

 .../bindings/clock/nuvoton,wpcm450-clk.yaml   |  66 +++
 .../bindings/timer/nuvoton,npcm7xx-timer.yaml |   8 +-
 arch/arm/boot/dts/nuvoton-wpcm450.dtsi        |  29 +-
 drivers/clk/Makefile                          |   1 +
 drivers/clk/clk-wpcm450.c                     | 375 ++++++++++++++++++
 drivers/clocksource/timer-npcm7xx.c           |  10 +
 drivers/reset/Kconfig                         |   2 +-
 .../dt-bindings/clock/nuvoton,wpcm450-clk.h   |  67 ++++
 8 files changed, 549 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/nuvoton,wpcm450-clk.yaml
 create mode 100644 drivers/clk/clk-wpcm450.c
 create mode 100644 include/dt-bindings/clock/nuvoton,wpcm450-clk.h

--
2.35.1