[PATCH V5 02/26] mmc: core: Prepare to support SD UHS-II cards

From: Victor Shih
Date: Fri Oct 14 2022 - 07:47:25 EST


From: Ulf Hansson <ulf.hansson@xxxxxxxxxx>

Updates in V4:
- Re-based, updated a comment and removed white-space.
- Moved MMC_VQMMC2_VOLTAGE_180 into a later patch in the series.

Update in previous version:
The SD UHS-II interface was introduced to the SD spec v4.00 several years
ago. The interface is fundamentally different from an electrical and a
protocol point of view, comparing to the legacy SD interface.

However, the legacy SD protocol is supported through a specific transport
layer (SD-TRAN) defined in the UHS-II addendum of the spec. This allows the
SD card to be managed in a very similar way as a legacy SD card, hence a
lot of code can be re-used to support these new types of cards through the
mmc subsystem.

Moreover, an SD card that supports the UHS-II interface shall also be
backwards compatible with the legacy SD interface, which allows a UHS-II
card to be inserted into a legacy slot. As a matter of fact, this is
already supported by mmc subsystem as of today.

To prepare to add support for UHS-II, this change puts the basic foundation
in the mmc core in place, allowing it to be more easily reviewed before
subsequent changes implements the actual support.

Basically, the approach here adds a new UHS-II bus_ops type and adds a
separate initialization path for the UHS-II card. The intent is to avoid us
from sprinkling the legacy initialization path, but also to simplify
implementation of the UHS-II specific bits.

At this point, there is only one new host ops added to manage the various
ios settings needed for UHS-II. Additional host ops that are needed, are
being added from subsequent changes.

Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
---
drivers/mmc/core/Makefile | 2 +-
drivers/mmc/core/core.c | 17 ++-
drivers/mmc/core/core.h | 1 +
drivers/mmc/core/sd_uhs2.c | 289 +++++++++++++++++++++++++++++++++++++
include/linux/mmc/card.h | 7 +
include/linux/mmc/host.h | 19 +++
6 files changed, 333 insertions(+), 2 deletions(-)
create mode 100644 drivers/mmc/core/sd_uhs2.c

diff --git a/drivers/mmc/core/Makefile b/drivers/mmc/core/Makefile
index 6a907736cd7a..15b067e8b0d1 100644
--- a/drivers/mmc/core/Makefile
+++ b/drivers/mmc/core/Makefile
@@ -7,7 +7,7 @@ obj-$(CONFIG_MMC) += mmc_core.o
mmc_core-y := core.o bus.o host.o \
mmc.o mmc_ops.o sd.o sd_ops.o \
sdio.o sdio_ops.o sdio_bus.o \
- sdio_cis.o sdio_io.o sdio_irq.o \
+ sdio_cis.o sdio_io.o sdio_irq.o sd_uhs2.o\
slot-gpio.o regulator.o
mmc_core-$(CONFIG_OF) += pwrseq.o
obj-$(CONFIG_PWRSEQ_SIMPLE) += pwrseq_simple.o
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index ef53a2578824..ab2a48e1e876 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -2234,6 +2234,18 @@ void mmc_rescan(struct work_struct *work)
goto out;
}

+ /*
+ * Ideally we should favor initialization of legacy SD cards and defer
+ * UHS-II enumeration. However, it seems like cards doesn't reliably
+ * announce their support for UHS-II in the response to the ACMD41,
+ * while initializing the legacy SD interface. Therefore, let's start
+ * with UHS-II for now.
+ */
+ if (!mmc_attach_sd_uhs2(host)) {
+ mmc_release_host(host);
+ goto out;
+ }
+
for (i = 0; i < ARRAY_SIZE(freqs); i++) {
unsigned int freq = freqs[i];
if (freq > host->f_max) {
@@ -2261,10 +2273,13 @@ void mmc_rescan(struct work_struct *work)

void mmc_start_host(struct mmc_host *host)
{
+ bool power_up = !(host->caps2 &
+ (MMC_CAP2_NO_PRESCAN_POWERUP | MMC_CAP2_SD_UHS2));
+
host->f_init = max(min(freqs[0], host->f_max), host->f_min);
host->rescan_disable = 0;

- if (!(host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)) {
+ if (power_up) {
mmc_claim_host(host);
mmc_power_up(host, host->ocr_avail);
mmc_release_host(host);
diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h
index f5f3f623ea49..2d80afc95e58 100644
--- a/drivers/mmc/core/core.h
+++ b/drivers/mmc/core/core.h
@@ -81,6 +81,7 @@ int mmc_detect_card_removed(struct mmc_host *host);
int mmc_attach_mmc(struct mmc_host *host);
int mmc_attach_sd(struct mmc_host *host);
int mmc_attach_sdio(struct mmc_host *host);
+int mmc_attach_sd_uhs2(struct mmc_host *host);

/* Module parameters */
extern bool use_spi_crc;
diff --git a/drivers/mmc/core/sd_uhs2.c b/drivers/mmc/core/sd_uhs2.c
new file mode 100644
index 000000000000..800957f74632
--- /dev/null
+++ b/drivers/mmc/core/sd_uhs2.c
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Linaro Ltd
+ *
+ * Author: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
+ *
+ * Support for SD UHS-II cards
+ */
+#include <linux/err.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+
+#include "core.h"
+#include "bus.h"
+#include "sd.h"
+#include "mmc_ops.h"
+
+static const unsigned int sd_uhs2_freqs[] = { 52000000, 26000000 };
+
+static int sd_uhs2_set_ios(struct mmc_host *host)
+{
+ struct mmc_ios *ios = &host->ios;
+
+ return host->ops->uhs2_set_ios(host, ios);
+}
+
+static int sd_uhs2_power_up(struct mmc_host *host)
+{
+ host->ios.vdd = fls(host->ocr_avail) - 1;
+ host->ios.clock = host->f_init;
+ host->ios.timing = MMC_TIMING_SD_UHS2;
+ host->ios.power_mode = MMC_POWER_UP;
+
+ return sd_uhs2_set_ios(host);
+}
+
+static void sd_uhs2_power_off(struct mmc_host *host)
+{
+ host->ios.vdd = 0;
+ host->ios.clock = 0;
+ host->ios.timing = MMC_TIMING_LEGACY;
+ host->ios.power_mode = MMC_POWER_OFF;
+
+ sd_uhs2_set_ios(host);
+}
+
+/*
+ * Run the phy initialization sequence, which mainly relies on the UHS-II host
+ * to check that we reach the expected electrical state, between the host and
+ * the card.
+ */
+static int sd_uhs2_phy_init(struct mmc_host *host)
+{
+ return 0;
+}
+
+/*
+ * Do the early initialization of the card, by sending the device init broadcast
+ * command and wait for the process to be completed.
+ */
+static int sd_uhs2_dev_init(struct mmc_host *host)
+{
+ return 0;
+}
+
+/*
+ * Run the enumeration process by sending the enumerate command to the card.
+ * Note that, we currently support only the point to point connection, which
+ * means only one card can be attached per host/slot.
+ */
+static int sd_uhs2_enum(struct mmc_host *host, u32 *node_id)
+{
+ return 0;
+}
+
+/*
+ * Read the UHS-II configuration registers (CFG_REG) of the card, by sending it
+ * commands and by parsing the responses. Store a copy of the relevant data in
+ * card->uhs2_config.
+ */
+static int sd_uhs2_config_read(struct mmc_host *host, struct mmc_card *card)
+{
+ return 0;
+}
+
+/*
+ * Based on the card's and host's UHS-II capabilities, let's update the
+ * configuration of the card and the host. This may also include to move to a
+ * greater speed range/mode. Depending on the updated configuration, we may need
+ * to do a soft reset of the card via sending it a GO_DORMANT_STATE command.
+ *
+ * In the final step, let's check if the card signals "config completion", which
+ * indicates that the card has moved from config state into active state.
+ */
+static int sd_uhs2_config_write(struct mmc_host *host, struct mmc_card *card)
+{
+ return 0;
+}
+
+/*
+ * Initialize the UHS-II card through the SD-TRAN transport layer. This enables
+ * commands/requests to be backwards compatible through the legacy SD protocol.
+ * UHS-II cards has a specific power limit specified for VDD1/VDD2, that should
+ * be set through a legacy CMD6. Note that, the power limit that becomes set,
+ * survives a soft reset through the GO_DORMANT_STATE command.
+ */
+static int sd_uhs2_legacy_init(struct mmc_host *host, struct mmc_card *card)
+{
+ return 0;
+}
+
+/*
+ * Allocate the data structure for the mmc_card and run the UHS-II specific
+ * initialization sequence.
+ */
+static int sd_uhs2_init_card(struct mmc_host *host)
+{
+ struct mmc_card *card;
+ u32 node_id;
+ int err;
+
+ err = sd_uhs2_dev_init(host);
+ if (err)
+ return err;
+
+ err = sd_uhs2_enum(host, &node_id);
+ if (err)
+ return err;
+
+ card = mmc_alloc_card(host, &sd_type);
+ if (IS_ERR(card))
+ return PTR_ERR(card);
+
+ card->uhs2_config.node_id = node_id;
+ card->type = MMC_TYPE_SD;
+
+ err = sd_uhs2_config_read(host, card);
+ if (err)
+ goto err;
+
+ err = sd_uhs2_config_write(host, card);
+ if (err)
+ goto err;
+
+ err = sd_uhs2_legacy_init(host, card);
+ if (err)
+ goto err;
+
+ host->card = card;
+ return 0;
+
+err:
+ mmc_remove_card(card);
+ return err;
+}
+
+static void sd_uhs2_remove(struct mmc_host *host)
+{
+ mmc_remove_card(host->card);
+ host->card = NULL;
+}
+
+static int sd_uhs2_alive(struct mmc_host *host)
+{
+ return mmc_send_status(host->card, NULL);
+}
+
+static void sd_uhs2_detect(struct mmc_host *host)
+{
+ int err;
+
+ mmc_get_card(host->card, NULL);
+ err = _mmc_detect_card_removed(host);
+ mmc_put_card(host->card, NULL);
+
+ if (err) {
+ sd_uhs2_remove(host);
+
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+ sd_uhs2_power_off(host);
+ mmc_release_host(host);
+ }
+}
+
+static int sd_uhs2_suspend(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_resume(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_runtime_suspend(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_runtime_resume(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_shutdown(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_hw_reset(struct mmc_host *host)
+{
+ return 0;
+}
+
+static const struct mmc_bus_ops sd_uhs2_ops = {
+ .remove = sd_uhs2_remove,
+ .alive = sd_uhs2_alive,
+ .detect = sd_uhs2_detect,
+ .suspend = sd_uhs2_suspend,
+ .resume = sd_uhs2_resume,
+ .runtime_suspend = sd_uhs2_runtime_suspend,
+ .runtime_resume = sd_uhs2_runtime_resume,
+ .shutdown = sd_uhs2_shutdown,
+ .hw_reset = sd_uhs2_hw_reset,
+};
+
+static int sd_uhs2_attach(struct mmc_host *host)
+{
+ int err;
+
+ err = sd_uhs2_power_up(host);
+ if (err)
+ goto err;
+
+ err = sd_uhs2_phy_init(host);
+ if (err)
+ goto err;
+
+ err = sd_uhs2_init_card(host);
+ if (err)
+ goto err;
+
+ mmc_attach_bus(host, &sd_uhs2_ops);
+
+ mmc_release_host(host);
+
+ err = mmc_add_card(host->card);
+ if (err)
+ goto remove_card;
+
+ mmc_claim_host(host);
+ return 0;
+
+remove_card:
+ mmc_remove_card(host->card);
+ host->card = NULL;
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+err:
+ sd_uhs2_power_off(host);
+ return err;
+}
+
+int mmc_attach_sd_uhs2(struct mmc_host *host)
+{
+ int i, err = 0;
+
+ if (!(host->caps2 & MMC_CAP2_SD_UHS2))
+ return -EOPNOTSUPP;
+
+ /* Turn off the legacy SD interface before trying with UHS-II. */
+ mmc_power_off(host);
+
+ /*
+ * Start UHS-II initialization at 52MHz and possibly make a retry at
+ * 26MHz according to the spec. It's required that the host driver
+ * validates ios->clock, to set a rate within the correct range.
+ */
+ for (i = 0; i < ARRAY_SIZE(sd_uhs2_freqs); i++) {
+ host->f_init = sd_uhs2_freqs[i];
+ err = sd_uhs2_attach(host);
+ if (!err)
+ break;
+ }
+
+ return err;
+}
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 8a30de08e913..7f6672000a48 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -211,6 +211,11 @@ struct sd_ext_reg {
#define SD_EXT_PERF_CMD_QUEUE (1<<4)
};

+struct sd_uhs2_config {
+ u32 node_id;
+ /* TODO: Extend with more register configs. */
+};
+
struct sdio_cccr {
unsigned int sdio_vsn;
unsigned int sd_vsn;
@@ -316,6 +321,8 @@ struct mmc_card {
struct sd_ext_reg ext_power; /* SD extension reg for PM */
struct sd_ext_reg ext_perf; /* SD extension reg for PERF */

+ struct sd_uhs2_config uhs2_config; /* SD UHS-II config */
+
unsigned int sdio_funcs; /* number of SDIO functions */
atomic_t sdio_funcs_probed; /* number of probed SDIO funcs */
struct sdio_cccr cccr; /* common card info */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index eb8bc5b9b0b7..0b4122b26352 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -63,6 +63,7 @@ struct mmc_ios {
#define MMC_TIMING_MMC_HS400 10
#define MMC_TIMING_SD_EXP 11
#define MMC_TIMING_SD_EXP_1_2V 12
+#define MMC_TIMING_SD_UHS2 13

unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */

@@ -91,6 +92,10 @@ struct mmc_clk_phase_map {
struct mmc_clk_phase phase[MMC_NUM_CLK_PHASES];
};

+struct sd_uhs2_caps {
+ /* TODO: Add UHS-II capabilities for the host. */
+};
+
struct mmc_host;

enum mmc_err_stat {
@@ -145,6 +150,17 @@ struct mmc_host_ops {
*/
void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);

+ /*
+ * The uhs2_set_ios callback is mandatory to implement for hosts that
+ * supports the SD UHS-II interface (MMC_CAP2_SD_UHS2), while the
+ * callback is unused for the other cases. Note that, the struct
+ * mmc_ios is being re-used for this as well.
+ *
+ * Expected return values for the uhs2_set_ios callback are a negative
+ * errno in case of a failure or zero for success.
+ */
+ int (*uhs2_set_ios)(struct mmc_host *host, struct mmc_ios *ios);
+
/*
* Return values for the get_ro callback should be:
* 0 for a read/write card
@@ -396,6 +412,7 @@ struct mmc_host {
MMC_CAP2_HS200_1_2V_SDR)
#define MMC_CAP2_SD_EXP (1 << 7) /* SD express via PCIe */
#define MMC_CAP2_SD_EXP_1_2V (1 << 8) /* SD express 1.2V */
+#define MMC_CAP2_SD_UHS2 (1 << 9) /* SD UHS-II support */
#define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
#define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
#define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
@@ -422,6 +439,8 @@ struct mmc_host {
#endif
#define MMC_CAP2_ALT_GPT_TEGRA (1 << 28) /* Host with eMMC that has GPT entry at a non-standard location */

+ struct sd_uhs2_caps uhs2_caps; /* Host UHS-II capabilities */
+
int fixed_drv_type; /* fixed driver type for non-removable media */

mmc_pm_flag_t pm_caps; /* supported pm features */
--
2.25.1