Re: [PATCH v5 3/3] arm64: dts: qcom: Add touchscreen and touchpad support for evoker

[Doug Anderson]

Hi,

On Fri, Sep 30, 2022 at 12:38 AM Sheng-Liang Pan
<sheng-liang.pan@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
>
> Change touchpad and touchscreen node for evoker
> Touchpad: SA461D-1011
> Touchscreen: GT7986U
>
> Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx>
> ---
>
> (no changes since v1)

nit: for patman, add:

Series-changes: 5
- Touchscreen / trackpad patch new for v5.

...and then you won't get the confusing "no changes since v1" message.

>  .../boot/dts/qcom/sc7280-herobrine-evoker.dtsi  | 17 +++++++----------
>  1 file changed, 7 insertions(+), 10 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi
> index e78072159d54b..c26f19371c8bc 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker.dtsi
> @@ -23,16 +23,15 @@ ap_tp_i2c: &i2c0 {
>         status = "okay";
>         clock-frequency = <400000>;
>
> -       trackpad: trackpad@2c {
> -               compatible = "hid-over-i2c";
> -               reg = <0x2c>;
> +       trackpad: trackpad@15 {
> +               compatible = "elan,ekth3000";
> +               reg = <0x15>;
>                 pinctrl-names = "default";
>                 pinctrl-0 = <&tp_int_odl>;
>
>                 interrupt-parent = <&tlmm>;
>                 interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
>
> -               hid-descr-addr = <0x20>;
>                 vcc-supply = <&pp3300_z1>;
>
>                 wakeup-source;
> @@ -43,18 +42,16 @@ ts_i2c: &i2c13 {
>         status = "okay";
>         clock-frequency = <400000>;
>
> -       ap_ts: touchscreen@10 {
> -               compatible = "elan,ekth6915";
> -               reg = <0x10>;
> -               pinctrl-names = "default";
> -               pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;

Why did you remove the pinctrl? Those should have stayed.


> +       touchscreen: touchscreen@5d {

nit: it's nice to keep the touchscreen label the same as the other
herobrine boards, so I'd keep this as:

ap_ts: touchscreen@5d {


> +               compatible = "goodix,gt7375p";
> +               reg = <0x5d>;
>
>                 interrupt-parent = <&tlmm>;
>                 interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
>
>                 reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
>
> -               vcc33-supply = <&ts_avdd>;
> +               vdd-supply = <&ts_avdd>;

What you have here is fine, but I've heard rumors that we might end up
needing to specify a different IO voltage rail. Right now the goodix
bindings / goodix driver don't handle that. ...anyway, no action items
for you right now but just a heads up.

-Doug