Re: [PATCH] MIPS: loongson32: Fix the validation failure of LS1B & LS1C Ethernet PHY

[Kelvin Cheung]

Hi Serge,
Your patch also works for me.
But what about the plat_dat->interface? Is it obsolete?

Serge Semin <fancer.lancer@xxxxxxxxx> 于2022年8月22日周一 01:10写道：
>
> Hello Keguang
>
> On Thu, Aug 18, 2022 at 01:00:19PM +0800, Keguang Zhang wrote:
> > From: Kelvin Cheung <keguang.zhang@xxxxxxxxx>
> >
> > The Ethernet of LS1B/LS1C doesn't work due to the stmmac driver
> > using phylink_generic_validate() instead of stmmac_validate().
> > Moreover the driver assumes the PHY interface mode
> > passed in platform data is always supported.
> >
> > stmmaceth stmmaceth.0 eth0: validation of gmii with support 00000000,00000000,000062cf and advertisement 00000000,00000000,000062cf failed: -EINVAL
> > stmmaceth stmmaceth.0 eth0: stmmac_open: Cannot attach to PHY (error: -22)
> >
> > This patch sets phy_interface field of platform data.
>
> I've got a similar fix in my repo, though didn't have a chance to test
> it out due to lacking any loongson hardware. I've discovered the
> issues on my still going way of the STMMAC driver refactoring. Anyway
> IMO the problem is a bit different than you describe and should be
> fixed in a bit different way. Please see a patch attached to this
> email. Could you test it out on your hw? If it fixes the problem you
> can resend it as v2 patch.
>
> -Sergey
>
> >
> > Fixes: 04a0683f7db4 ("net: stmmac: convert to phylink_generic_validate()")
> > Fixes: d194923d51c9 ("net: stmmac: fill in supported_interfaces")
> > Signed-off-by: Kelvin Cheung <keguang.zhang@xxxxxxxxx>
> > ---
> >  arch/mips/loongson32/common/platform.c | 2 ++
> >  1 file changed, 2 insertions(+)
> >
> > diff --git a/arch/mips/loongson32/common/platform.c b/arch/mips/loongson32/common/platform.c
> > index 794c96c2a4cd..741aace80b80 100644
> > --- a/arch/mips/loongson32/common/platform.c
> > +++ b/arch/mips/loongson32/common/platform.c
> > @@ -147,8 +147,10 @@ static struct plat_stmmacenet_data ls1x_eth0_pdata = {
> >       .phy_addr               = -1,
> >  #if defined(CONFIG_LOONGSON1_LS1B)
> >       .interface              = PHY_INTERFACE_MODE_MII,
> > +     .phy_interface          = PHY_INTERFACE_MODE_MII,
> >  #elif defined(CONFIG_LOONGSON1_LS1C)
> >       .interface              = PHY_INTERFACE_MODE_RMII,
> > +     .phy_interface          = PHY_INTERFACE_MODE_RMII,
> >  #endif
> >       .mdio_bus_data          = &ls1x_mdio_bus_data,
> >       .dma_cfg                = &ls1x_eth_dma_cfg,
> >
> > base-commit: 568035b01cfb107af8d2e4bd2fb9aea22cf5b868
> > --
> > 2.34.1
> >



-- 
Best regards,

Kelvin Cheung