Re: [RFC] PM: domains: Reverse the order of performance and enabling ops

From: Ulf Hansson
Date: Tue Aug 16 2022 - 07:31:11 EST


[...]

> > >
> > > When the last active consumer suspends (in our case here, device A), ->power_off
> > > will be called first disabling the PD, then the ->set_performance will
> > > 'release' that lowest perf level the device A requested but will not
> > > call to FW since the PD is already disabled. This would make
> > > sure there are not two calls with two different levels to the FW.
> >
> > I understand what you want to achieve, but I think the ->power_off()
> > scenario may be a bit more tricky.
> >
> > For example, it would be perfectly fine for genpd to keep the PM
> > domain powered-on, even when the device A gets runtime suspended (a
> > genpd governor may prevent it). In other words, we may end up not
> > getting the ->power_off() callback invoked at all, even if there are
> > no runtime resumed devices in the PM domain.
> >
> > Could this lead to problems on the provider side, when trying to take
> > into account the different combinations of sequences?
>
> Correct me if I'm wrong, but even if a genpd governor would prevent
> the power_off to be called, if we do the reversal, since the power
> domain is not off, the provider would lower the performance state and
> that's it. The responsability falls on the provider, but so does with
> the current order of the calls.
>
> So I don't see how this could lead to problems compared to the current
> order of the calls.

Alright, I agree, it shouldn't really matter then.

>
> Maybe I missunderstood your point, so please correct me if I'm getting
> this wrong.
>
> >
> > >
> > > Now, most of this depends on the provider's way of doing things.
> > > But in order to allow the provider to do what is described above, it
> > > needs to know about the perf level before it is asked to power on a PD.
> > > Same applies to powering off.
> > >
> > > > >
> > > > > I think it makes more sense for the ->set_performance in this case to act as a
> > > > > way to tell the provider that a specific device has yeilded its voltage level
> > > > > request. That way the provider can drop the voltage to the minimum requested by
> > > > > the active consumers of that PD.
> > > >
> > > > The genpd provider can know if the PM domain is powered on or off,
> > > > when the ->set_performance_state() callback is invoked. If it's
> > > > powered off, it may then decide to "cache" the request for the
> > > > performance level request, until it gets powered on.
> > >
> > > But the ->set_performance is called only after ->power_on, so the PD
> > > will always be on when ->set_performance checks. And this is what my
> > > patch is trying to change actually.
> > >
> > > >
> > > > Although, I don't see how a genpd provider should be able to cache a
> > > > performance state request, when the PM domain is already powered on
> > > > (which is what you propose, if I understand correctly), that simply
> > > > doesn't work for the other scenarios.
> > >
> > > I explained this above. The provider will need to check if the PD is on
> > > and only write to FW if it is. Otherwise it will cache the value for
> > > when the power_on is called.
> >
> > As indicated above, it looks to me that you may need to check a
> > combination of things at the provider side. Is relying on whether
> > genpd is on/off to decide when to apply or cache a performance state,
> > really sufficient? I could certainly be wrong though.
>
> I don't think there is any change from this point of view, when compared
> to the current order. Even with the current order, the provider would
> either cache the performance state if the power domain is off, or would
> apply it if the power domain is on.

For the Qcom case, I don't think it's that simple on the genpd provider side.

With the changes you propose in the $subject patch, I think there are
two specific scenarios when the genpd can be powered off and when the
->set_performance_state() callback can get called. These scenarios can
just rely on whether the genpd is powered off or not, to make the best
decision. See more below.

*) In genpd_runtime_resume() we make sure to *raise* the performance
state prior to power on the PM domain, if the PM domain is powered
off, of course. In this way the ->set_performance_state() callback may
be invoked when the genpd is powered off, to *raise* the performance
state.

**) In genpd_runtime_suspend() we may power off the PM domain, before
invoking the ->set_performance_state() callback to *lower* the
performance state.

In other words, just checking whether the genpd is powered off, to
decide to cache/postpone the call to the FW to set a new performance
state, would mean that we may end up running in a higher performance
state than actually needed, right?

Perhaps if we would check if the performance state is lowered (or set
to zero) too, that should improve the situation, right?

>
> >
> > Perhaps if you can provide a corresponding patch for the genpd
> > provider side too, that can help to convince me.
>
> The qcom-rpmhpd actually does that even now. On set_performance, it caches
> the performance state (corner) if the power domain is disabled, and it
> applies (aggregates the corner) if the power domain is enabled.

Okay, good!

As stated above, this sounds like it can be improved then, right?

Kind regards
Uffe