RE: [PATCH V9 5/5] iio: accel: sca3300: Add inclination channels

From: LI Qingwu
Date: Thu Jun 30 2022 - 20:58:14 EST




> -----Original Message-----
> From: Jonathan Cameron <jic23@xxxxxxxxxx>
> Sent: Sunday, June 26, 2022 11:02 PM
> To: LI Qingwu <Qing-wu.Li@xxxxxxxxxxxxxxxxxxxxxxx>
> Cc: lars@xxxxxxxxxx; robh+dt@xxxxxxxxxx; tomas.melin@xxxxxxxxxxx;
> andy.shevchenko@xxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> linux-kernel@xxxxxxxxxxxxxxx; HAEMMERLE Thomas
> <thomas.haemmerle@xxxxxxxxxxxxxxxxxxxx>; linux-iio@xxxxxxxxxxxxxxx
> Subject: Re: [PATCH V9 5/5] iio: accel: sca3300: Add inclination channels
>
> This email is not from Hexagon’s Office 365 instance. Please be careful while
> clicking links, opening attachments, or replying to this email.
>
>
> On Sun, 29 May 2022 06:18:53 +0000
> LI Qingwu <Qing-wu.Li@xxxxxxxxxxxxxxxxxxxxxxx> wrote:
>
> > Different from SCA3300, SCL3300 can output inclination angles.
> > Angles are formed from acceleration with following equations:
> > ANG_X = atan2(accx , sqrt(pow(accy , 2) + pow(accz , 2))) ANG_Y =
> > atan2(accy , sqrt(pow(accx , 2) + pow(accz , 2))) ANG_Z = atan2(accz ,
> > sqrt(pow(accx , 2) + pow(accy , 2)))
> >
> > The commit adds the output of the raw value, scale and scale_available
> > of angles.
> >
> > New interfaces:
> > in_incli_scale
> > in_incli_scale_available
> > in_incli_x_raw
> > in_incli_y_raw
> > in_incli_z_raw
> > Data converted by application of scale to degrees.
> >
> > Signed-off-by: LI Qingwu <Qing-wu.Li@xxxxxxxxxxxxxxxxxxxxxxx>
>
> I was looking at this driver whilst sanity checking something unrelated to this
> patch and noticed...
>
> sca3300_trigger_handler directly references sca3300_channels rather than
> through indio_dev->channels.
>
> I think that means you'll get a buffer overrun if you enable the inclination
> channels with buffered capture. Please check if we need to modify that code
> slightly.
>
> I'm also fairly sure the timestamp will end up in the wrong place as
> iio_push_to_buffers_with_timestamp() assumes it's at the end. Please confirm
> you've tested with appropriate channels enabled and the test code in tools/iio
>
> I think the changes needed are to put the incli channels before the timestamp
> but you'll need to use separate enum for that. Also make the trigger handler
> use the channels array for the specific device via indio_dev->channels.
>
> Thanks,
>
> Jonathan

Fix in the coming patch, Thanks.
LI Qingwu

>
> > ---
> > drivers/iio/accel/sca3300.c | 76
> > +++++++++++++++++++++++++++++++++++--
> > 1 file changed, 73 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/iio/accel/sca3300.c b/drivers/iio/accel/sca3300.c
> > index 9683dce21073..861f6906beee 100644
> > --- a/drivers/iio/accel/sca3300.c
> > +++ b/drivers/iio/accel/sca3300.c
> > @@ -44,12 +44,18 @@
> > #define SCA3300_VALUE_RS_ERROR 0x3
> > #define SCA3300_MASK_RS_STATUS GENMASK(1, 0)
> >
> > +#define SCL3300_REG_ANG_CTRL 0x0C
> > +#define SCL3300_ANG_ENABLE 0x1F
> > +
> > enum sca3300_scan_indexes {
> > SCA3300_ACC_X = 0,
> > SCA3300_ACC_Y,
> > SCA3300_ACC_Z,
> > SCA3300_TEMP,
> > SCA3300_TIMESTAMP,
> > + SCA3300_INCLI_X,
> > + SCA3300_INCLI_Y,
> > + SCA3300_INCLI_Z,
> > };
> >
> > #define SCA3300_ACCEL_CHANNEL(index, reg, axis)
> { \
> > @@ -73,6 +79,23 @@ enum sca3300_scan_indexes {
> > },
> \
> > }
> >
> > +#define SCA3300_INCLI_CHANNEL(index, reg, axis)
> { \
> > + .type = IIO_INCLI,
> \
> > + .address = reg,
> \
> > + .modified = 1,
> \
> > + .channel2 = IIO_MOD_##axis,
> \
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
> \
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> \
> > + .info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE),
> \
> > + .scan_index = index,
> \
> > + .scan_type =
> { \
> > + .sign = 's',
> \
> > + .realbits = 16,
> \
> > + .storagebits = 16,
> \
> > + .endianness = IIO_CPU,
> \
> > + },
> \
> > +}
> > +
> > #define SCA3300_TEMP_CHANNEL(index, reg)
> { \
> > .type = IIO_TEMP,
> \
> > .address = reg,
> \
> > @@ -106,15 +129,36 @@ static const int sca3300_accel_scale_map[] = {0,
> > 1, 2, 2}; static const int scl3300_accel_scale[][2] = {{0, 167}, {0,
> > 333}, {0, 83}}; static const int scl3300_accel_scale_map[] = {0, 1,
> > 2};
> >
> > +static const int scl3300_incli_scale[][2] = {{0, 5495}}; static const
> > +int scl3300_incli_scale_map[] = {0, 0, 0};
> > +
> > static const int sca3300_avail_modes_map[] = {0, 1, 2, 3}; static
> > const int scl3300_avail_modes_map[] = {0, 1, 3};
> >
> > +static const struct iio_chan_spec scl3300_channels[] = {
> > + SCA3300_ACCEL_CHANNEL(SCA3300_ACC_X, 0x1, X),
> > + SCA3300_ACCEL_CHANNEL(SCA3300_ACC_Y, 0x2, Y),
> > + SCA3300_ACCEL_CHANNEL(SCA3300_ACC_Z, 0x3, Z),
> > + SCA3300_TEMP_CHANNEL(SCA3300_TEMP, 0x05),
> > + IIO_CHAN_SOFT_TIMESTAMP(4),
> > + SCA3300_INCLI_CHANNEL(SCA3300_INCLI_X, 0x09, X),
> > + SCA3300_INCLI_CHANNEL(SCA3300_INCLI_Y, 0x0A, Y),
> > + SCA3300_INCLI_CHANNEL(SCA3300_INCLI_Z, 0x0B, Z), };
> > +
> > static const unsigned long sca3300_scan_masks[] = {
> > BIT(SCA3300_ACC_X) | BIT(SCA3300_ACC_Y) | BIT(SCA3300_ACC_Z) |
> > BIT(SCA3300_TEMP),
> > 0
> > };
> >
> > +static const unsigned long scl3300_scan_masks[] = {
> > + BIT(SCA3300_ACC_X) | BIT(SCA3300_ACC_Y) | BIT(SCA3300_ACC_Z) |
> > + BIT(SCA3300_TEMP) |
> > + BIT(SCA3300_INCLI_X) | BIT(SCA3300_INCLI_Y) |
> BIT(SCA3300_INCLI_Z),
> > + 0
> > +};
> > +
> > struct sca3300_chip_info {
> > const char *name;
> > const unsigned long *scan_masks; @@ -123,12 +167,16 @@ struct
> > sca3300_chip_info {
> > u8 num_accel_scales;
> > const int (*accel_scale)[2];
> > const int *accel_scale_map;
> > + const int (*incli_scale)[2];
> > + const int *incli_scale_map;
> > + u8 num_incli_scales;
> > u8 num_freqs;
> > const int *freq_table;
> > const int *freq_map;
> > const int *avail_modes_table;
> > u8 num_avail_modes;
> > u8 chip_id;
> > + bool angle_supported;
> > };
> >
> > /**
> > @@ -167,21 +215,26 @@ static const struct sca3300_chip_info
> sca3300_chip_tbl[] = {
> > .avail_modes_table = sca3300_avail_modes_map,
> > .num_avail_modes = 4,
> > .chip_id = SCA3300_WHOAMI_ID,
> > + .angle_supported = false,
> > },
> > {
> > .name = "scl3300",
> > - .scan_masks = sca3300_scan_masks,
> > - .channels = sca3300_channels,
> > - .num_channels = ARRAY_SIZE(sca3300_channels),
> > + .scan_masks = scl3300_scan_masks,
> > + .channels = scl3300_channels,
> > + .num_channels = ARRAY_SIZE(scl3300_channels),
> > .num_accel_scales = ARRAY_SIZE(scl3300_accel_scale)*2,
> > .accel_scale = scl3300_accel_scale,
> > .accel_scale_map = scl3300_accel_scale_map,
> > + .incli_scale = scl3300_incli_scale,
> > + .incli_scale_map = scl3300_incli_scale_map,
> > + .num_incli_scales = ARRAY_SIZE(scl3300_incli_scale)*2,
> > .num_freqs = ARRAY_SIZE(scl3300_lp_freq),
> > .freq_table = scl3300_lp_freq,
> > .freq_map = scl3300_lp_freq_map,
> > .avail_modes_table = scl3300_avail_modes_map,
> > .num_avail_modes = 3,
> > .chip_id = SCL3300_WHOAMI_ID,
> > + .angle_supported = true,
> > },
> > };
> >
> > @@ -400,6 +453,11 @@ static int sca3300_read_raw(struct iio_dev
> *indio_dev,
> > if (ret)
> > return ret;
> > switch (chan->type) {
> > + case IIO_INCLI:
> > + index = data->chip->incli_scale_map[index];
> > + *val = data->chip->incli_scale[index][0];
> > + *val2 = data->chip->incli_scale[index][1];
> > + return IIO_VAL_INT_PLUS_MICRO;
> > case IIO_ACCEL:
> > index = data->chip->accel_scale_map[index];
> > *val = data->chip->accel_scale[index][0];
> > @@ -486,6 +544,13 @@ static int sca3300_init(struct sca3300_data
> > *sca_data,
> >
> > sca_data->chip = &sca3300_chip_tbl[i];
> >
> > + if (sca_data->chip->angle_supported) {
> > + ret = sca3300_write_reg(sca_data,
> SCL3300_REG_ANG_CTRL,
> > + SCL3300_ANG_ENABLE);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > return 0;
> > }
> >
> > @@ -521,6 +586,11 @@ static int sca3300_read_avail(struct iio_dev
> *indio_dev,
> > switch (mask) {
> > case IIO_CHAN_INFO_SCALE:
> > switch (chan->type) {
> > + case IIO_INCLI:
> > + *vals = (const int *)data->chip->incli_scale;
> > + *length = data->chip->num_incli_scales;
> > + *type = IIO_VAL_INT_PLUS_MICRO;
> > + return IIO_AVAIL_LIST;
> > case IIO_ACCEL:
> > *vals = (const int *)data->chip->accel_scale;
> > *length = data->chip->num_accel_scales;