Re: [PATCH 1/2] dt-bindings: interrupt-controller: Add Renesas RZ/G2L Interrupt Controller

[Lad, Prabhakar]

Hi Geert,

Thank you for the review.

On Thu, Apr 28, 2022 at 10:32 AM Geert Uytterhoeven
<geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Prabhakar,
>
> On Fri, Apr 22, 2022 at 12:12 AM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> > Add DT bindings for the Renesas RZ/G2L Interrupt Controller.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
>
> Thanks for your patch!
>
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzg2l-irqc.yaml
> > @@ -0,0 +1,131 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/interrupt-controller/renesas,rzg2l-irqc.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Renesas RZ/G2L (and alike SoC's) Interrupt Controller (IA55)
> > +
> > +maintainers:
> > +  - Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > +  - Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> > +
> > +description: |
> > +  IA55 performs various interrupt controls including synchronization for the external
> > +  interrupts of NMI, IRQ, and GPIOINT and the interrupts of the built-in peripheral
> > +  interrupts output by each IP. And it notifies the interrupt to the GIC
> > +    - IRQ sense select for 8 external interrupts, mapped to 8 GIC SPI interrupts
> > +    - GPIO pins used as external interrupt input pins, mapped to 32 GIC SPI interrupts
> > +    - NMI edge select (NMI is not treated as NMI exception and supports fall edge and
> > +      stand-up edge detection interrupts)
> > +
> > +allOf:
> > +  - $ref: /schemas/interrupt-controller.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    items:
> > +      - enum:
> > +          - renesas,r9a07g044-irqc    # RZ/G2L
> > +      - const: renesas,rzg2l-irqc
> > +
> > +  '#interrupt-cells':
> > +    const: 2
>
> What is the meaning of the cells? IRQ number + flags, I assume?
IRQ number and the type.

> How are the numbers mapped, do you need a DT bindings header?
No, just plain numbers are used (driver handles the validation of the
interrupt numbering), for example like below,

&eth0 {
   ...
   status = "okay";

   phy0: ethernet-phy@7 {
     compatible = "ethernet-phy-id0022.1640",
                           "ethernet-phy-ieee802.3-c22";
     reg = <7>;
     interrupt-parent = <&irqc>;
     interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
    ...
  };
};

And for the GPIO:

key-1 {
      gpios = <&pinctrl RZG2L_GPIO(43, 0) GPIO_ACTIVE_HIGH>;
      linux,code = <KEY_1>;
      linux,input-type = <EV_KEY>;
      wakeup-source;
      label = "SW1";
};

> Perhaps it would make sense to increase to 3 cells, so you can use
> one cell for the type (cfr. e.g. GIC_SPI), and the second for the
> plain index within the type?
>
Could you please elaborate on this. Are you referring to the type here
as the type to be set up in the GIC?

Cheers,
Prabhakar

> The rest LGTM, but I'm not an interrupt expert, so I'm curious in
> hearing Marc's opinion.
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds