Re: [PATCH v1 1/3] dt-bindings: iio: adc: add AD4130

From: Jonathan Cameron
Date: Sun Apr 24 2022 - 12:03:07 EST



>
> >>
> >> Signed-off-by: Cosmin Tanislav <cosmin.tanislav@xxxxxxxxxx>
> >> ---
> >> .../bindings/iio/adc/adi,ad4130.yaml | 255 ++++++++++++++++++
> >> 1 file changed, 255 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml
> >> new file mode 100644
> >> index 000000000000..e9dce54e9802
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml
> >> @@ -0,0 +1,255 @@
> >> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> >> +# Copyright 2022 Analog Devices Inc.
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/iio/adc/adi,ad4130.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Analog Devices AD4130 ADC device driver
> >> +
> >> +maintainers:
> >> + - Cosmin Tanislav <cosmin.tanislav@xxxxxxxxxx>
> >> +
> >> +description: |
> >> + Bindings for the Analog Devices AD4130 ADC. Datasheet can be found here:
> >> + https://www.analog.com/media/en/technical-documentation/data-sheets/AD4130-8.pdf
> >> +
> >> +properties:
> >> + compatible:
> >> + enum:
> >> + - adi,ad4130-8-16-lfcsp
> >> + - adi,ad4130-8-16-wlcsp
> >> + - adi,ad4130-8-24-lfcsp
> >> + - adi,ad4130-8-24-wlcsp
> >
> > What are the variants? They look to possibly be package differences?
> > + resolution differences.
> > They definitely need some description here.
> > It may make more sense to have one compatible and then some extra
> > booleans to say what it supported.
> >
>
> Packaging + available interrupt pins + resolution. Is having extra
> booleans to describe what is supported really the best approach?
> It's not really about how the hardware is configured anymore, is it?
> They're different chips.

It's unusual to have compatibles for packaging alone and I couldn't find
any clear references to the variants. Maybe best we can do here is
add a bunch of documentation.

>
> > Long shot, but do the different packages have different model IDs?
> > The datasheet says
> > Model ID: 24-bit WLCSP Model ID. These bits are set by default for each model and
> > are read only. If there is one for each of these models then it would be
> > better to have a single compatible and do the detection of variant in
> > the driver.
> >
> > I'm not immediately spotting the resolution information in the data sheet.
> > It is marked Preliminary but if there are details missing, please mention
> > in cover letter so we don't go looking for information that doesn't exist.
> >
>
> I don't have enough information about the other models to know what
> Model IDs they will have. That's why I took this approach.

My inclination is to probably not add the compatibles for those until we
do have that information.

>
> >> +
> >> + reg:
> >> + maxItems: 1
> >> +
> >> + clocks:
> >> + maxItems: 1
> >> + description: phandle to the master clock (mclk)
> >> +
> >> + clock-names:
> >> + items:
> >> + - const: mclk
> >> +
> >> + interrupts:
> >> + minItems: 1
> >> + maxItems: 1
> >> +
> >> + interrupt-names:
> >> + minItems: 1
> >> + maxItems: 1
> >> + description:
> >> + Default if not supplied is dout-int.
> >> + items:
> >> + enum:
> >> + - dout-int
> >> + - clk
> >> + - p1
> >
> > This is unusual. It is probably helpful to add more description to
> > explain that the data ready/ fifo interrupt can be routed to any of these
> > pins.
>
> Is it unusual? ADIS16480 follows a similar approach.

I think I got thrown by the large number of choices for a single interrupt.
Flexibility of interrupt routing is common but I've never seen 4 choices for
a single interrupt before :)

>
> description: |
> Specify which interrupt pin should be configured as Data Ready / FIFO
> interrupt.
> Default if not supplied is dout-int.
>
> How does this sound?

Sounds good to me.

>
> >
> >> + - dout
> >> +
> >> + '#address-cells':
> >> + const: 1
> >> +
> >> + '#size-cells':
> >> + const: 0
> >> +
> >> + refin1-supply:
> >> + description: refin1 supply. Can be used as reference for conversion.
> >> +
> >> + refin2-supply:
> >> + description: refin2 supply. Can be used as reference for conversion.
> >> +
> >> + avdd-supply:
> >> + description: AVDD voltage supply. Can be used as reference for conversion.
> >
> > Whilst these are optional in theory, you should call out that they must be
> > provided if any of the channels use them as a reference.
> >
>
> I thought that "Can be used as reference for conversion." + it being an
> option in adi,reference-select property would make it obvious, no?

More obvious is always good, but you are probably right and I was just
not terribly awake when I wrote that :)

>
> >> +
> >> + iovdd-supply:
> >> + description: IOVDD voltage supply. Used for the chip interface.
> >> +
> >> + spi-max-frequency:
> >> + maximum: 5000000
> >> +
> >> + adi,mclk-sel:
> >> + description: |
> >> + Select the clock.
> >> + 0: Internal 76.8kHz clock.
> >> + 1: Internal 76.8kHz clock, output to the CLK pin.
> >> + 2: External 76.8kHz clock.
> >> + 3. External 153.6kHz clock.
> >
> > For the external clocks, can we use the fact that one is supplied
> > as enough to tell us we should be using them? Then query the
> > frequency directly from that clock?
> >
>
> Aren't we supposed to set the frequency of that clock ourselves,
> in the driver?

True, I got that backwards.

>
> > If no clock provided then clearly internal. All that is
> > necessary after that is a boolean to control if the CLK output
> > is enabled or not (and ideally constrain that to only be possible
> > if in internal clock mode).
> >
>
> Well...
>
> So, mclk present => external, not present => internal.
> adi,int-clk-out-enable to specify if the internal clock should be
> exposed? adi,ext-clk-freq to specify the desired clock speed of the
> external clk?

Yes that sounds good to me. I just don't like magic numbers
in bindings if we can avoid them. With the above a reader should
be able to figure out what is going on without reading this doc.

>
> >> + $ref: /schemas/types.yaml#/definitions/uint32
> >> + enum: [0, 1, 2, 3]
> >> + default: 0
> >> +
> >> + adi,int-ref-en:
> >
> > Mentioned below...
> >
> >> + description: |
> >> + Specify if internal reference should be enabled.
> >> + type: boolean
> >> + default: true
> >> +
> >> + adi,bipolar:
> >> + description: Specify if the device should be used in bipolar mode.
> >> + type: boolean
> >> + default: false
> >> +
> >> + adi,vbias-pins:
> >> + description: Analog inputs to apply a voltage bias of (AVDD − AVSS) / 2 to.
> >> + items:
> >> + minimum: 0
> >> + maximum: 15
> >
> > If I read things correctly VBIAS_CONTROL is a bitmap across the 16 input lines.
> > So why use a single value rather than either a list of pins, or a bitmap?
> >
>
> Umm. Isn't this a list of pins? That's why everything is plural here.
> I guess I should add `maxItems: 16`?
> I already added `$ref: /schemas/types.yaml#/definitions/uint32-array`.

Ah. Yes, with an array and maxItems this will be fine I think.

>
> >> +
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - interrupts
> >> +
> >> +patternProperties:
> >> + "^channel@([0-9]|1[0-5])$":
> >> + type: object
> >> + $ref: adc.yaml
> >> +
> >> + properties:
> >> + reg:
> >> + description: |
> >> + The channel number.
> >> + items:
> >> + minimum: 0
> >> + maximum: 15
> >> +
> >> + diff-channels:
> >> + description: |
> >> + Besides the analog inputs available, internal inputs can be used.
> >> + 16: Internal temperature sensor.
> >> + 17: AVss
> >> + 18: Internal reference.
> >> + 19: DGND.
> >> + 20: (AVDD − AVSS)/6+
> >> + 21: (AVDD − AVSS)/6-
> >> + 22: (IOVDD − DGND)/6+
> >> + 23: (IOVDD − DGND)/6-
> >> + 24: (ALDO − AVSS)/6+
> >> + 25: (ALDO − AVSS)/6-
> >> + 26: (DLDO − DGND)/6+
> >> + 27: (DLDO − DGND)/6-
> >> + 28: V_MV_P
> >> + 29: V_MV_M
> >> + $ref: adc.yaml
> >> + items:
> >> + minimum: 0
> >> + maximum: 29
> >
> > Interesting. So we have a part that has a 16 channel sequencer, but
> > can you have more channels as long as you don't want them all at once?
> > For example, I doubt anyone wants to permanently configure a device to monitor
> > the various supplies, but they will want to occasionally.
> >
> > As such, perhaps we need to treat this device more flexibly?
> > There are obviously contraints on what channels + references make sense
> > but maybe we should allow more than 16 to be specified?
> >
>
> Ehhhhh. Look at the driver. It's already pushing 2k+ lines with
> the 8 setups for 16 channels situation + all the extra options the
> chip provides. If we also make it so that channels are rewritten at
> runtime, it will turn into a mess. Or at least I don't see a clean
> way of adding that. Besides, then I'd have to do all these extra
> allocations depending on the number of channels in the device tree...
> It gets complicated. If a customer expresses his interest in this,
> I guess I'll have to add it.
> Also, presumably the extra inputs are marketed as diagnostics.

Another approach would be to 'always' provide those diagnostic channels
but not via buffered interface (if that's sensible to do). Then potentially
drop them from this binding?

Maybe waiting for customer demand is the best way to go. Even if you
added a path to read them without them being in DT later it should be
easy enough to maintain backwards compatibility.

Jonathan