Re: [RFCv3 4/6] media: dt-bindings: add DS90UB954-Q1 video deserializer

[Rob Herring]

On Sun, 06 Feb 2022 12:59:37 +0100, Luca Ceresoli wrote:
> Describe the Texas Instruments DS90UB954-Q1, a 2-input MIPI CSI-2 video
> deserializer with I2C Address Translator and remote GPIOs.
> 
> Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> 
> ---
> 
> Changes RFCv2 -> RFCv3:
> 
>  - rewrite in yaml
>  - use new layout based on remote-chips under the main deser node
>  - new clock configuration based on common clock framework
> 
> Changes RFCv1 -> RFCv2:
> 
>  - add explicit aliases for the FPD-link RX ports (optional)
>  - add proper remote GPIO description
> ---
>  .../bindings/media/i2c/ti,ds90ub954-q1.yaml   | 235 ++++++++++++++++++
>  MAINTAINERS                                   |   6 +
>  2 files changed, 241 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml: properties:reg-names: {'description': 'Names of I2C address used to communicate with the chip, must match\nthe "reg" values; mandatory if there are 2 or more addresses.\n"main" is the main I2C address, used to access shared registers.\n"rxport0" and "rxport1" are the I2C alias to access FPD-link RX\nport specific registers; must not be used by other slaves on the\nsame bus. "ser0" and "ser1" are the I2C alias to access the remote\nserializer connected on each FPD-link RX port; must not be used by\nother slaves on the same bus.\n', 'minItems': 1, 'maxItems': 5, 'items': [{'const': 'main'}, {'const': 'rxport0'}, {'const': 'rxport1'}, {'const': 'ser0'}, {'const': 'ser1'}]} should not be valid under {'required': ['maxItems']}
	hint: "maxItems" is not needed with an "items" list
	from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml: ignoring, error in schema: properties: reg-names
Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.example.dt.yaml:0:0: /example-0/i2c@0/deser@3d: failed to match any schema with compatible: ['ti,ds90ub954-q1']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1588972

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.