Re: [PATCH] ARM: dts: aspeed: Add TYAN S8036 BMC machine

From: Joel Stanley
Date: Mon Dec 20 2021 - 23:45:13 EST

Next message: PANICKER HARISH (Temp) (QUIC): "RE: [PATCH v3] Bluetooth: hci_qca: Stop IBS timer during BT OFF"
Previous message: Joel Stanley: "Re: [PATCH v8] ARM: dts: aspeed: Adding Facebook Bletchley BMC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, 30 Nov 2021 at 18:01, Ali El-Haj-Mahmoud <aaelhaj@xxxxxxxxxx> wrote:
>
> The TYAN S8036 is a server platform with an ASPEED AST2500 BMC.
>
> Signed-off-by: Ali El-Haj-Mahmoud <aaelhaj@xxxxxxxxxx>

Reviewed-by: Joel Stanley <joel@xxxxxxxxx>

Applied for v5.17

> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts | 466 ++++++++++++++++++++
> 2 files changed, 468 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8b7f150be39e..b0ca5e88942b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1499,4 +1499,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-quanta-q71l.dtb \
> aspeed-bmc-supermicro-x11spi.dtb \
> aspeed-bmc-inventec-transformers.dtb \
> - aspeed-bmc-tyan-s7106.dtb
> + aspeed-bmc-tyan-s7106.dtb \
> + aspeed-bmc-tyan-s8036.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts b/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
> new file mode 100644
> index 000000000000..873e7bf2361e
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
> @@ -0,0 +1,466 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Tyan S8036 BMC";
> + compatible = "tyan,s8036-bmc", "aspeed,ast2500";
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200 earlycon";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + p2a_memory: region@987f0000 {
> + no-map;
> + reg = <0x987f0000 0x00010000>; /* 64KB */
> + };
> +
> + vga_memory: framebuffer@9f000000 {
> + no-map;
> + reg = <0x9f000000 0x01000000>; /* 16M */
> + };
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>; /* 16M */
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + identify {
> + gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
> + };
> +
> + heartbeat {
> + gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
> + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
> + <&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
> + <&adc 12>, <&adc 13>, <&adc 14>;
> + };
> +
> + iio-hwmon-battery {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 15>;
> + };
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + label = "bmc";
> + status = "okay";
> + m25p,fast-read;
> +#include "openbmc-flash-layout.dtsi"
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + label = "pnor";
> + m25p,fast-read;
> + };
> +};
> +
> +&uart1 {
> + /* Rear RS-232 connector */
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd1_default
> + &pinctrl_rxd1_default>;
> +};
> +
> +&uart2 {
> + /* RS-232 connector on header */
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_txd2_default
> + &pinctrl_rxd2_default>;
> +};
> +
> +&uart3 {
> + /* Alternative to vuart to internally connect (route) to uart1
> + * when vuart cannot be used due to BIOS limitations.
> + */
> + status = "okay";
> +};
> +
> +&uart4 {
> + /* Alternative to vuart to internally connect (route) to the
> + * external port usually used by uart1 when vuart cannot be
> + * used due to BIOS limitations.
> + */
> + status = "okay";
> +};
> +
> +&uart5 {
> + /* BMC "debug" (console) UART; connected to RS-232 connector
> + * on header; selectable via jumpers as alternative to uart2
> + */
> + status = "okay";
> +};
> +
> +&uart_routing {
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> +
> + /* We enable the VUART here, but leave it in a state that does
> + * not interfere with the SuperIO. The goal is to have both the
> + * VUART and the SuperIO available and decide at runtime whether
> + * the VUART should actually be used. For that reason, configure
> + * an "invalid" IO address and an IRQ that is not used by the
> + * BMC.
> + */
> + aspeed,lpc-io-reg = <0xffff>;
> + aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> +};
> +
> +&p2a {
> + status = "okay";
> + memory-region = <&p2a_memory>;
> +};
> +
> +&lpc_snoop {
> + status = "okay";
> + snoop-ports = <0x80>;
> +};
> +
> +&adc {
> + status = "okay";
> +};
> +
> +&vhub {
> + status = "okay";
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default>;
> +
> + /* CPU fan */
> + fan@0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00>;
> + };
> +
> + /* PWM group for chassis fans #1, #2, #3 and #4 */
> + fan@2 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02>;
> + };
> +
> + fan@3 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x03>;
> + };
> +
> + fan@4 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04>;
> + };
> +
> + fan@5 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x05>;
> + };
> +
> + /* PWM group for chassis fans #5 and #6 */
> + fan@6 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06>;
> + };
> +
> + fan@7 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x07>;
> + };
> +};
> +
> +&i2c0 {
> + /* Directly connected to Sideband-Temperature Sensor Interface (APML) */
> + status = "okay";
> +};
> +
> +&i2c1 {
> + /* Directly connected to IPMB HDR. */
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + /* BMC EEPROM, incl. mainboard FRU */
> + eeprom@50 {
> + compatible = "atmel,24c256";
> + reg = <0x50>;
> + };
> + /* Also connected to:
> + * - BCM5720
> + * - FPGA
> + * - FAN HDR
> + * - FPIO HDR
> + */
> +};
> +
> +&i2c3 {
> + status = "okay";
> +
> + /* PSU1 FRU @ 0xA0 */
> + eeprom@50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + };
> +
> + /* PSU2 FRU @ 0xA2 */
> + eeprom@51 {
> + compatible = "atmel,24c02";
> + reg = <0x51>;
> + };
> +
> + /* PSU1 @ 0xB0 */
> + power-supply@58 {
> + compatible = "pmbus";
> + reg = <0x58>;
> + };
> +
> + /* PSU2 @ 0xB2 */
> + power-supply@59 {
> + compatible = "pmbus";
> + reg = <0x59>;
> + };
> +
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> + /* Hardware monitor with temperature sensors */
> + nct7802@28 {
> + compatible = "nuvoton,nct7802";
> + reg = <0x28>;
> + channel@0 { /* LTD */
> + reg = <0>;
> + status = "okay";
> + };
> + channel@1 { /* RTD1 */
> + reg = <1>;
> + status = "okay";
> + sensor-type = "temperature";
> + temperature-mode = "thermistor";
> + };
> +
> + channel@2 { /* RTD2 */
> + reg = <2>;
> + status = "okay";
> + sensor-type = "temperature";
> + temperature-mode = "thermistor";
> + };
> +
> + channel@3 { /* RTD3 */
> + reg = <3>;
> + status = "okay";
> + sensor-type = "temperature";
> + };
> + };
> +
> + /* Also connected to:
> + * - PCA9544
> + * - CLK BUFF
> + * - OCP FRU
> + */
> +};
> +
> +&i2c6 {
> + status = "okay";
> + /* Connected to:
> + * - PCA9548 @0xE0
> + * - PCA9548 @0xE2
> + * - PCA9544 @0xE4
> + */
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + /* Connected to:
> + * - PCH SMBUS #4
> + */
> +};
> +
> +&i2c8 {
> + status = "okay";
> +
> + /* Not connected */
> +};
> +
> +&mac0 {
> + status = "okay";
> + use-ncsi;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii1_default>;
> +};
> +
> +&mac1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
> +};
> +
> +&ibt {
> + status = "okay";
> +};
> +
> +&kcs1 {
> + status = "okay";
> + aspeed,lpc-io-reg = <0xca8>;
> +};
> +
> +&kcs3 {
> + status = "okay";
> + aspeed,lpc-io-reg = <0xca2>;
> +};
> +
> +/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +/* We're following the GPIO naming as defined at
> + * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md.
> + *
> + * Notes on led-identify and id-button:
> + * - A physical button is connected to id-button which
> + * triggers the clock on a D flip-flop. The /Q output of the
> + * flip-flop drives its D input.
> + * - The flip-flop's Q output drives led-identify which is
> + * connected to LEDs.
> + * - With that, every button press toggles the LED between on and off.
> + *
> + * Notes on power-, reset- and nmi- button and control:
> + * - The -button signals can be used to monitor physical buttons.
> + * - The -control signals can be used to actuate the specific
> + * operation.
> + * - In hardware, the -button signals are connected to the -control
> + * signals through drivers with the -control signals being
> + * protected through diodes.
> + */
> +&gpio {
> + status = "okay";
> + gpio-line-names =
> + /*A0*/ "",
> + /*A1*/ "",
> + /*A2*/ "led-identify", /* in/out: BMC_CHASSIS_ID_LED_L */
> + /*A3*/ "",
> + /*A4*/ "",
> + /*A5*/ "",
> + /*A6*/ "",
> + /*A7*/ "",
> + /*B0-B7*/ "","","","","","","","",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0*/ "",
> + /*D1*/ "",
> + /*D2*/ "power-chassis-good", /* in: PWR_GOOD_LED -- Check if this is Z3?*/
> + /*D3*/ "platform-reset", /* in: RESET_LED_L */
> + /*D4*/ "",
> + /*D5*/ "",
> + /*D6*/ "",
> + /*D7*/ "",
> + /*E0*/ "power-button", /* in: BMC_SYS_MON_PWR_BTN_L */
> + /*E1*/ "power-chassis-control", /* out: BMC_ASSERT_PWR_BTN */
> + /*E2*/ "reset-button", /* in: BMC_SYS_MOS_RST_BTN_L*/
> + /*E3*/ "reset-control", /* out: BMC_ASSERT_RST_BTN */
> + /*E4*/ "nmi-button", /* in: BMC_SYS_MON_NMI_BTN_L */
> + /*E5*/ "nmi-control", /* out: BMC_ASSERT_NMI_BTN */
> + /*E6*/ "TSI_RESERT",
> + /*E7*/ "led-heartbeat", /* out: BMC_GPIOE7 */
> + /*F0*/ "",
> + /*F1*/ "clear-cmos-control", /* out: BMC_ASSERT_CLR_CMOS_L */
> + /*F2*/ "",
> + /*F3*/ "",
> + /*F4*/ "led-fault", /* out: BMC_HWM_FAULT_LED_L */
> + /*F5*/ "BMC_SYS_FAULT_LED_L",
> + /*F6*/ "BMC_ASSERT_BIOS_WP_L",
> + /*F7*/ "",
> + /*G0-G7*/ "","","","","","","","",
> + /*H0-H7*/ "","","","","","","","",
> + /*I0-I7*/ "","","","","","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","","","","",
> + /*P0-P7*/ "","","","","","","","",
> + /*Q0*/ "",
> + /*Q1*/ "",
> + /*Q2*/ "",
> + /*Q3*/ "",
> + /*Q4*/ "",
> + /*Q5*/ "",
> + /*Q6*/ "id-button", /* in: BMC_CHASSIS_ID_BTN_L */
> + /*Q7*/ "",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "","","","","","","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","","","","","","",
> + /*Z0-Z2*/ "","","",
> + /*Z3*/ "post-complete", /* BMC_SYS_MON_PWROK */
> + /*Z4-Z7*/ "","","","",
> + /*AA0*/ "",
> + /*AA1*/ "",
> + /*AA2*/ "",
> + /*AA3*/ "",
> + /*AA4*/ "",
> + /*AA5*/ "",
> + /*AA6*/ "",
> + /*AA7*/ "BMC_ASSERT_BMC_READY",
> + /*AB0*/ "BMC_SPD_SEL",
> + /*AB1-AB7*/ "","","","","","","";
> +};
> --
> 2.34.0.rc2.393.gf8c9666880-goog
>

Next message: PANICKER HARISH (Temp) (QUIC): "RE: [PATCH v3] Bluetooth: hci_qca: Stop IBS timer during BT OFF"
Previous message: Joel Stanley: "Re: [PATCH v8] ARM: dts: aspeed: Adding Facebook Bletchley BMC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]