Re: [PATCH v3] arm64: dts: qcom: sc7280: Add bluetooth node on SC7280

[Matthias Kaehlcke]

On Tue, Dec 07, 2021 at 11:43:43AM +0530, Balakrishna Godavarthi wrote:

> Subject: arm64: dts: qcom: sc7280: Add bluetooth node on SC7280

nit: the node is added to the IDP boards, not sc7280 in general

> From: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxx>
> 
> Add bluetooth SoC WCN6750 node for SC7280 IDP boards.
> 
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> v3:
>   * Addressed reviewers comments

that's not overly useful, instead you should describe what changed

>   * Added pin config for sw_ctrl line.
> v2:
>   * merged two patches into one
>   * Removed unused comments
>   * Removed pinmux & pin conf.
>   * Addressed reviewers comments
> 
> v1: initial patch
> ---
>  arch/arm64/boot/dts/qcom/sc7280-idp.dts  |  4 ++++
>  arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 37 ++++++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280-idp2.dts |  4 ++++
>  3 files changed, 45 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 9b991ba..19bd228 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -56,6 +56,10 @@
>  	};
>  };
>  
> +&bluetooth {
> +	vddio-supply = <&vreg_l19b_1p8>;
> +};
> +
>  &ipa {
>  	status = "okay";
>  	modem-init;
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> index d623d71..b8b00dc 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> @@ -14,6 +14,11 @@
>  #include "pmk8350.dtsi"
>  
>  / {
> +	aliases {
> +		bluetooth0 = &bluetooth;
> +		serial1 = &uart7;
> +	};
> +
>  	gpio-keys {
>  		compatible = "gpio-keys";
>  		label = "gpio-keys";
> @@ -422,6 +427,23 @@
>  				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
>  	pinctrl-names = "default", "sleep";
>  	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
> +
> +	bluetooth: bluetooth {
> +		compatible = "qcom,wcn6750-bt";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_en>, <&swctrl_gpio>;
> +		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> +		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
> +		vddaon-supply = <&vreg_s7b_0p9>;
> +		vddbtcxmx-supply = <&vreg_s7b_0p9>;
> +		vddrfacmn-supply = <&vreg_s7b_0p9>;
> +		vddrfa0p8-supply = <&vreg_s7b_0p9>;
> +		vddrfa1p7-supply = <&vreg_s1b_1p8>;
> +		vddrfa1p2-supply = <&vreg_s8b_1p2>;
> +		vddrfa2p2-supply = <&vreg_s1c_2p2>;
> +		vddasd-supply = <&vreg_l11c_2p8>;
> +		max-speed = <3200000>;
> +	};
>  };
>  
>  /* PINCTRL - additions to nodes defined in sc7280.dtsi */
> @@ -491,6 +513,14 @@
>  };
>  
>  &tlmm {
> +	bt_en: bt-en {
> +		pins = "gpio85";
> +		function = "gpio";
> +		drive-strength = <2>;

is it really necessary to specify the drive strength?

Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml:

  drive-strength:
    enum: [2, 4, 6, 8, 10, 12, 14, 16]
    default: 2

The default is 2, so it shouldn't be needed.

> +		output-low;
> +		bias-disable;
> +	};
> +
>  	nvme_pwren: nvme-pwren {
>  		function = "gpio";
>  	};
> @@ -554,6 +584,13 @@
>  		 */
>  		bias-pull-up;
>  	};
> +
> +	swctrl_gpio: swctrl-gpio {

The 'gpio' suffix isn't really useful.

I suggest to use the signal name from the schematics "mos-sw-ctrl" or
call it "bt-sw-ctrl". If you use the schematic name then this should
be also done for the enable pin.