Re: [PATCH 1/2] rtc: max31343: Add a driver for Maxim MAX31343

[afirago]

Hello,

Thanks for your review.

On 01.12.2021 01:32, Alexandre Belloni wrote:
> Hello,
>
> On 16/10/2021 22:21:17+0300, Alexey Firago wrote:
> > +#define MAX31343_REG_TIMER_CFG	(0x05)
> > +#define  TIMER_CFG_TFS		GENMASK(1, 0) /* Timer frequency */
> > +#define  TIMER_CFG_TRPT		BIT(2) /* Timer repeat mode */
> > +#define  TIMER_CFG_TPAUSE	BIT(3) /* Timer Pause */
> > +#define  TIMER_CFG_TE		BIT(4) /* Timer enable */
> > +
> > +/* RTC section */
> > +#define MAX31343_REG_SEC	(0x06)
> > +#define  SEC10_MASK	GENMASK(6, 4) /* RTC seconds in multiples of 10 */
> > +#define  SEC_MASK	GENMASK(3, 0) /* RTC seconds value */
>
> I'm not convinced having separate masks is useful here, was that
> automatically generated?

I've just exported those definitions from the table in the datasheet 
prior to creating the driver.

> > +static int max31343_rtc_set_time(struct device *dev, struct rtc_time *tm)
> > +{
> > +	struct max31343_rtc_data *max31343 = dev_get_drvdata(dev);
> > +	u8 date[7];
> > +	int ret;
> > +
> > +	dev_dbg(dev, "RTC set time %04d-%02d-%02d %02d/%02d/%02d\n",
> > +		tm->tm_year + 1900, tm->tm_mon, tm->tm_mday,
> > +		tm->tm_hour, tm->tm_min, tm->tm_sec);
> > +
>
> This could use %ptR

Will change it (or probably completely remove it) after hwmon review.

> > +	date[0] = bin2bcd(tm->tm_sec);
> > +	date[1] = bin2bcd(tm->tm_min);
> > +	date[2] = bin2bcd(tm->tm_hour);
> > +	date[3] = tm->tm_wday;
> > +	date[4] = bin2bcd(tm->tm_mday);
> > +	date[5] = bin2bcd(tm->tm_mon + 1);
> > +
> > +	if (tm->tm_year >= 200)
> > +		date[5] |= CENTURY;
> > +	date[6] = bin2bcd(tm->tm_year % 100);
> > +
> > +	ret = regmap_bulk_write(max31343->regmap, MAX31343_REG_SEC, date,
> > +				sizeof(date));
> > +	return ret;
> > +}
> > +
>
> [...]
>
> > +static int
> > +max31343_probe(struct i2c_client *client, const struct i2c_device_id *id)
> > +{
> > +	struct max31343_rtc_data *max31343 = NULL;
> > +	int ret, status;
> > +	struct nvmem_config nvmem_cfg = {
> > +		.name = "max31343_nvram",
> > +		.word_size = 1,
> > +		.stride = 1,
> > +		.size = MAX31343_RAM_SIZE,
> > +		.type = NVMEM_TYPE_BATTERY_BACKED,
> > +		.reg_read = max31343_nvram_read,
> > +		.reg_write = max31343_nvram_write,
> > +	};
> > +
> > +	max31343 = devm_kzalloc(&client->dev, sizeof(struct max31343_rtc_data),
> > +				GFP_KERNEL);
> > +	if (!max31343)
> > +		return -ENOMEM;
> > +
> > +	max31343->regmap = devm_regmap_init_i2c(client, &max31343_regmap_config);
> > +	if (IS_ERR(max31343->regmap))
> > +		return PTR_ERR(max31343->regmap);
> > +
> > +	i2c_set_clientdata(client, max31343);
> > +
> > +	ret = regmap_read(max31343->regmap, MAX31343_REG_STATUS, &status);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	max31343->rtc = devm_rtc_allocate_device(&client->dev);
> > +	if (IS_ERR(max31343->rtc))
> > +		return PTR_ERR(max31343->rtc);
> > +
> > +	max31343->rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
> > +	max31343->rtc->range_max = RTC_TIMESTAMP_END_2199;
>
> For my information, did you check the time continuity in this interval?

Yes, I've checked setting of out-of-range values, checked edge values 
and checked 2099 -> 2100 -> 2101 transitions.

> > +	max31343->rtc->ops = &max31343_rtc_ops;
> > +	ret = devm_rtc_register_device(max31343->rtc);
> > +	if (ret)
> > +		return ret;
> > +
> > +	nvmem_cfg.priv = max31343->regmap;
> > +	devm_rtc_nvmem_register(max31343->rtc, &nvmem_cfg);
> > +	max31343_hwmon_register(&client->dev);
>
> The whole driver seems ok, I'd like to get a review from the hwmon
> maintainers on the hwmon part as it is quite large.

Ok.

Thanks,
Alexey