Re: [PATCH V2 4/5] arm64: dts: imx8mm-beacon: Enable OV5640 Camera

[Laurent Pinchart]

Hi Adam,

On Sun, Nov 21, 2021 at 09:07:26PM -0600, Adam Ford wrote:
> On Sun, Nov 21, 2021 at 5:18 PM Laurent Pinchart wrote:
> > On Sat, Nov 06, 2021 at 10:54:26AM -0500, Adam Ford wrote:
> > > The baseboard has support for a TDNext 5640 Camera which
> > > uses an OV5640 connected to a 2-lane CSI2 interface.
> > >
> > > With the CSI and mipi_csi2 drivers pointing to an OV5640 camera, the media
> > > pipeline can be configured with the following:
> > >
> > >     media-ctl --links "'ov5640 1-003c':0->'imx7-mipi-csis.0':0[1]"
> > >
> > > The camera and various nodes in the pipeline can be configured for UYVY:
> > >     media-ctl -v -V "'ov5640 1-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
> > >     media-ctl -v -V "'csi':0 [fmt:UYVY8_1X16/640x480 field:none]"
> > >
> > > Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> >
> > As the ov5640 is on an add-on module, would a DT overlay be better ?
> 
> At least for the Beacon / LogicPD boards, I would prefer to avoid the
> overlays.  We have an i.M6Q and an OMAP3 board with cameras enabled in
> our development kit device trees.  If the cameras are not connected,
> they just display a message that the cameras are not communicating and
> move on.  I'm OK with that.

You know the board better than I do, so I won't push against this, but I
still think it may not lead to the best user experience, especially if a
user wanted to connect a different sensor to the development board.

> > > ---
> > > V2:  No change
> > >
> > >  .../freescale/imx8mm-beacon-baseboard.dtsi    | 58 +++++++++++++++++++
> > >  1 file changed, 58 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> > > index 6f5e63696ec0..0fb95f4a5e78 100644
> > > --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
> > > @@ -43,6 +43,16 @@ reg_audio: regulator-audio {
> > >               enable-active-high;
> > >       };
> > >
> > > +     reg_camera: regulator-camera {
> > > +             compatible = "regulator-fixed";
> > > +             regulator-name = "mipi_pwr";
> > > +             regulator-min-microvolt = <2800000>;
> > > +             regulator-max-microvolt = <2800000>;
> > > +             gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>;
> > > +             enable-active-high;
> > > +             startup-delay-us = <100000>;
> > > +     };
> > > +
> > >       reg_usdhc2_vmmc: regulator-usdhc2 {
> > >               compatible = "regulator-fixed";
> > >               regulator-name = "VSD_3V3";
> > > @@ -67,6 +77,10 @@ sound {
> > >       };
> > >  };
> > >
> > > +&csi {
> > > +     status = "okay";
> > > +};
> > > +
> > >  &ecspi2 {
> > >       pinctrl-names = "default";
> > >       pinctrl-0 = <&pinctrl_espi2>;
> > > @@ -90,6 +104,30 @@ &i2c2 {
> > >       pinctrl-names = "default";
> > >       pinctrl-0 = <&pinctrl_i2c2>;
> > >       status = "okay";
> > > +
> > > +     camera@3c {
> > > +             compatible = "ovti,ov5640";
> > > +             pinctrl-names = "default";
> > > +             pinctrl-0 = <&pinctrl_ov5640>;
> > > +             reg = <0x3c>;
> > > +             clocks = <&clk IMX8MM_CLK_CLKO1>;
> > > +             clock-names = "xclk";
> > > +             assigned-clocks = <&clk IMX8MM_CLK_CLKO1>;
> > > +             assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
> > > +             assigned-clock-rates = <24000000>;
> > > +             AVDD-supply = <&reg_camera>;  /* 2.8v */
> > > +             powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> > > +             reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> > > +
> > > +             port {
> > > +                     /* MIPI CSI-2 bus endpoint */
> > > +                     ov5640_to_mipi_csi2: endpoint {
> > > +                             remote-endpoint = <&imx8mm_mipi_csi_in>;
> > > +                             clock-lanes = <0>;
> > > +                             data-lanes = <1 2>;
> > > +                     };
> > > +             };
> > > +     };
> > >  };
> > >
> > >  &i2c4 {
> > > @@ -141,6 +179,18 @@ pca6416_1: gpio@21 {
> > >       };
> > >  };
> > >
> > > +&mipi_csi {
> > > +     status = "okay";
> > > +     ports {
> > > +             port@0 {
> > > +                     imx8mm_mipi_csi_in: endpoint {
> > > +                             remote-endpoint = <&ov5640_to_mipi_csi2>;
> > > +                             data-lanes = <1 2>;
> > > +                     };
> > > +             };
> > > +     };
> > > +};
> > > +
> > >  &sai3 {
> > >       pinctrl-names = "default";
> > >       pinctrl-0 = <&pinctrl_sai3>;
> > > @@ -209,6 +259,14 @@ MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28        0x41
> > >               >;
> > >       };
> > >
> > > +     pinctrl_ov5640: ov5640grp {
> > > +             fsl,pins = <
> > > +                     MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7               0x19
> > > +                     MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6               0x19
> > > +                     MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1      0x59
> > > +             >;
> > > +     };
> > > +
> > >       pinctrl_pcal6414: pcal6414-gpiogrp {
> > >               fsl,pins = <
> > >                       MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27               0x19

-- 
Regards,

Laurent Pinchart