Re: [net-next PATCH] net: dsa: qca8k: make sure PAD0 MAC06 exchange is disabled

From: Ansuel Smith
Date: Tue Nov 02 2021 - 14:28:58 EST


On Tue, Nov 02, 2021 at 08:26:55PM +0200, Vladimir Oltean wrote:
> On Tue, Nov 02, 2021 at 06:56:29PM +0100, Ansuel Smith wrote:
> > Some device set MAC06 exchange in the bootloader. This cause some
> > problem as we don't support this strange mode and we just set the port6
> > as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
> > instead of port0. Add an extra check and explicitly disable MAC06 exchange
> > to correctly configure the port PAD config.
> >
> > Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> > ---
>
> Reviewed-by: Vladimir Oltean <olteanv@xxxxxxxxx>
>
> Since net-next has closed, please add
>
> Fixes: 3fcf734aa482 ("net: dsa: qca8k: add support for cpu port 6")
>
> and resend to the "net" tree.
>

Oh sorry! I checked http://vger.kernel.org/~davem/net-next.html
before posting and it does say it's open. Will resend sorry.

> > drivers/net/dsa/qca8k.c | 8 ++++++++
> > drivers/net/dsa/qca8k.h | 1 +
> > 2 files changed, 9 insertions(+)
> >
> > Some comments here:
> > Resetting the switch using the sw reg doesn't reset the port PAD
> > configuration. I was thinking if it would be better to clear all the
> > pad configuration but considering that the entire reg is set by phylink
> > mac config, I think it's not necessary as the PAD related to the port will
> > be reset anyway with the new values. Have a dirty configuration on PAD6
> > doesn't cause any problem as we have that port disabled and it would be
> > reset and configured anyway if defined.
> >
> > diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> > index ea7f12778922..a429c9750add 100644
> > --- a/drivers/net/dsa/qca8k.c
> > +++ b/drivers/net/dsa/qca8k.c
> > @@ -1109,6 +1109,14 @@ qca8k_setup(struct dsa_switch *ds)
> > if (ret)
> > return ret;
> >
> > + /* Make sure MAC06 is disabled */
> > + ret = qca8k_reg_clear(priv, QCA8K_REG_PORT0_PAD_CTRL,
> > + QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
> > + if (ret) {
> > + dev_err(priv->dev, "failed disabling MAC06 exchange");
> > + return ret;
> > + }
> > +
> > /* Enable CPU Port */
> > ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0,
> > QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
> > diff --git a/drivers/net/dsa/qca8k.h b/drivers/net/dsa/qca8k.h
> > index e10571a398c9..128b8cf85e08 100644
> > --- a/drivers/net/dsa/qca8k.h
> > +++ b/drivers/net/dsa/qca8k.h
> > @@ -34,6 +34,7 @@
> > #define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8)
> > #define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8)
> > #define QCA8K_REG_PORT0_PAD_CTRL 0x004
> > +#define QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN BIT(31)
> > #define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19)
> > #define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18)
> > #define QCA8K_REG_PORT5_PAD_CTRL 0x008
> > --
> > 2.32.0
> >

--
Ansuel