Re: [RFC PATCH] USB: host: ehci-atmel: Allow enabling HSIC on SAMA5D2

From: Alexander Dahl
Date: Mon Sep 06 2021 - 03:20:54 EST


Hello Nicolas,

Am Donnerstag, 2. September 2021, 17:33:50 CEST schrieb Nicolas Ferre:
> Hi Alexander,
>
> On 24/08/2021 at 08:37, Alexander Dahl wrote:
> > Unlike other SoC series featuring the 'atmel,at91sam9g45-ehci' USB EHCI
> > controller, which have embedded USB high-speed transceivers for each
> > port, the third port on the SAMA5D2 series is HSIC only. That HSIC
> > interface is not enabled after a power-on reset, but can be enabled by
> > setting a flag in a vendor specific EHCI register.
> >
> > The register offsets added to the new header file were compared with
> > those for the SAM9G45, SAM9X25, SAMA5D3, SAMA5D4, and SAM9X60 series and
> > there are no differences in the offsets or contents of those registers.
> > Which of those additional vendor specific registers are supported,
> > differs by SoC family. So while the HSIC enable feature is currently
> > only present for SAMA5D2, it probably does not hurt to set it on the
> > other families, hence no additional check for SoC family here.
> >
> > Tested on a custom board featuring a SAMA5D27C-D5M SiP connected to an
> > USB3503 hub with an upstream HSIC interface.
> >
> > Link: https://community.atmel.com/forum/sama5d2-using-hsic-under-linux
> > Signed-off-by: Alexander Dahl <ada@xxxxxxxxxxx>
>
> Sorry for not having coming back to you earlier, summertime...

I had one week off last week due to a mild infection myself, so we just
proceed here and now. (-:

> What you are looking for is what Cristian developed in our "vendor tree"
> and that needs to be "Mainlined":
> https://github.com/linux4sam/linux-at91/commit/ca368f544899c14b03df9ce751068
> 4f03acf1bf9

Looks like it does what it should from quick code inspection. One could
nitpick some things, maybe I add some comments on GitHub.

> It allows us to have a gigabit Ethernet HSIC connected on our sama5d2
> ICP board. It works well for some time.

Good to hear.

> For DT, we rely on the standard "phy_type" property set to "hsic" as
> highlighted in this DT node on the ICP board precisely:
> https://github.com/linux4sam/linux-at91/blob/master/arch/arm/boot/dts/at91-s
> ama5d2_icp.dts#L766
>
> This way we can use the of_usb_get_phy_mode() standard function:
> https://github.com/linux4sam/linux-at91/blob/master/drivers/usb/phy/of.c#L28

I noticed that phy_type property, but did not follow that approach, because
that USB block in SAMA5D2 has three ports, where one (A) is shared with a
device port, two (A and B) have embedded transceivers, and only the third (C)
has that HSIC interface, but nothing else. So the flag has no effect on port A
and B anyways, and I would have found it misleading to set phy_type to HSIC
for the whole USB block.

> All this tells me that I would prefer Cristi's approach. If agreed,
> we'll make sure to make progress on the mainlining part soon.

I don't mind. If that's your preferred approach, I will happily test it. Was
the series already posted to upstream?

> Hope that it helps. Best regards,
> Nicolas

Yes, indeed. Thanks for your feedback.

Greets
Alex

>
> > ---
> >
> > Notes:
> > - for introducing new dt binding, would be nice to convert old one
> >
> > first, probably needs split up and multiple iteration review?
> >
> > - name of that new dt property?
> > - register definitions put to a separate file, like
> >
> > 'drivers/usb/host/ehci-fsl.h'
> >
> > - unsure where exactly in the probe process that register write
> > should
> >
> > happen, datasheet gives no hint
> >
> > - should suspend/resume be considered?
> >
> > drivers/usb/host/ehci-atmel.c | 17 +++++++++++++++++
> > drivers/usb/host/ehci-atmel.h | 19 +++++++++++++++++++
> > 2 files changed, 36 insertions(+)
> > create mode 100644 drivers/usb/host/ehci-atmel.h
> >
> > diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c
> > index e893467d659c..f8d9e686c082 100644
> > --- a/drivers/usb/host/ehci-atmel.c
> > +++ b/drivers/usb/host/ehci-atmel.c
> > @@ -20,6 +20,7 @@
> >
> > #include <linux/usb/hcd.h>
> >
> > #include "ehci.h"
> >
> > +#include "ehci-atmel.h"
> >
> > #define DRIVER_DESC "EHCI Atmel driver"
> >
> > @@ -85,6 +86,7 @@ static void atmel_stop_ehci(struct platform_device
> > *pdev)
> >
> > static int ehci_atmel_drv_probe(struct platform_device *pdev)
> > {
> >
> > + struct device_node *np = pdev->dev.of_node;
> >
> > struct usb_hcd *hcd;
> > const struct hc_driver *driver = &ehci_atmel_hc_driver;
> > struct resource *res;
> >
> > @@ -149,6 +151,14 @@ static int ehci_atmel_drv_probe(struct
> > platform_device *pdev)>
> > atmel_start_ehci(pdev);
> >
> > + if (of_property_read_bool(np, "atmel,enable-hsic")) {
> > + u32 tmp;
> > +
> > + tmp = ehci_readl(ehci, hcd->regs + AT91_UHPHS_INSNREG08);
> > + tmp |= AT91_UHPHS_HSIC_EN;
> > + ehci_writel(ehci, tmp, hcd->regs + AT91_UHPHS_INSNREG08);
> > + }
> > +
> >
> > retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
> > if (retval)
> >
> > goto fail_add_hcd;
> >
> > @@ -170,10 +180,17 @@ static int ehci_atmel_drv_probe(struct
> > platform_device *pdev)>
> > static int ehci_atmel_drv_remove(struct platform_device *pdev)
> > {
> >
> > struct usb_hcd *hcd = platform_get_drvdata(pdev);
> >
> > + struct ehci_hcd *ehci;
> > + u32 tmp;
> >
> > usb_remove_hcd(hcd);
> > usb_put_hcd(hcd);
> >
> > + ehci = hcd_to_ehci(hcd);
> > + tmp = ehci_readl(ehci, hcd->regs + AT91_UHPHS_INSNREG08);
> > + tmp &= ~AT91_UHPHS_HSIC_EN;
> > + ehci_writel(ehci, tmp, hcd->regs + AT91_UHPHS_INSNREG08);
> > +
> >
> > atmel_stop_ehci(pdev);
> >
> > return 0;
> >
> > diff --git a/drivers/usb/host/ehci-atmel.h b/drivers/usb/host/ehci-atmel.h
> > new file mode 100644
> > index 000000000000..4c4998c2a6dd
> > --- /dev/null
> > +++ b/drivers/usb/host/ehci-atmel.h
> > @@ -0,0 +1,19 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Vendor specific definitions for EHCI on Atmel/Microchip SoCs.
> > + *
> > + * © 2021 Alexander Dahl <ada@xxxxxxxxxxx>
> > + */
> > +#ifndef EHCI_ATMEL_H
> > +#define EHCI_ATMEL_H
> > +
> > +/* device specific register offsets, taken from SAMA5D2 datasheet */
> > +
> > +#define AT91_UHPHS_INSNREG06 0xA8 /* AHB Error Status Register
> > */ +
> > +#define AT91_UHPHS_INSNREG07 0xAC /* AHB Master Error Address
> > Register */ +
> > +#define AT91_UHPHS_INSNREG08 0xB0 /* HSIC Enable/Disable
> > Register */ +#define AT91_UHPHS_HSIC_EN (1 << 2) /* HSIC
> > Enable/Disable */ +
> > +#endif /* ECHI_ATMEL_H */
> >
> > base-commit: e22ce8eb631bdc47a4a4ea7ecf4e4ba499db4f93
> > --
> > 2.30.2


--