RE: [PATCH 2/2] gpio: modepin: Add driver support for modepin GPIO controller

From: Piyush Mehta
Date: Mon Jun 21 2021 - 13:09:42 EST


Hello Linus,

Thanks for the review comments.
We will address all the reviews in the next version.

Regards,
Piyush Mehta

-----Original Message-----
From: Linus Walleij <linus.walleij@xxxxxxxxxx>
Sent: Friday, June 18, 2021 3:14 PM
To: Piyush Mehta <piyushm@xxxxxxxxxx>
Cc: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>; Rob Herring <robh+dt@xxxxxxxxxx>; open list:GPIO SUBSYSTEM <linux-gpio@xxxxxxxxxxxxxxx>; open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; linux-kernel <linux-kernel@xxxxxxxxxxxxxxx>; Linux ARM <linux-arm-kernel@xxxxxxxxxxxxxxxxxxx>; git <git@xxxxxxxxxx>; Srinivas Goud <sgoud@xxxxxxxxxx>; Michal Simek <michals@xxxxxxxxxx>
Subject: Re: [PATCH 2/2] gpio: modepin: Add driver support for modepin GPIO controller

Hi Piyush!

thanks for your patch!

On Tue, Jun 15, 2021 at 10:06 AM Piyush Mehta <piyush.mehta@xxxxxxxxxx> wrote:

> This patch adds support for the mode pin GPIO controller. GPIO Modepin
> driver set and get the value and status of the PS_MODE pin, based on
> device-tree pin configuration. These 4-bits boot-mode pins are
> dedicated configurable as input/output. After the stabilization of the
> system, these mode pins are sampled.
>
> Signed-off-by: Piyush Mehta <piyush.mehta@xxxxxxxxxx>

OK, sounds interesting!

> +#include <linux/slab.h>

I think I saw somewhere that this is not needed anymore, check if you need it.

> +#define GET_OUTEN_PIN(pin) (1U << (pin))

Delete this macro and just use BIT(pin) inline.
#include <linux/bits.h>

> +static int modepin_gpio_get_value(struct gpio_chip *chip, unsigned
> +int pin) {
> + u32 out_en;
> + u32 regval = 0;
> + int ret;
> +
> + out_en = GET_OUTEN_PIN(pin);

Drop this and out_en

> + ret = zynqmp_pm_bootmode_read(&regval);
> + if (ret) {
> + pr_err("modepin: get value err %d\n", ret);
> + return ret;
> + }
> +
> + return (out_en & (regval >> 8U)) ? 1 : 0;

return !!(regval & BIT(pin + 8));

should work and is easier to read IMO. We just check the right bit immediately.

> +static void modepin_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
> + int state) {
> + u32 out_en;
> + u32 bootpin_val = 0;
> + int ret;
> +
> + out_en = GET_OUTEN_PIN(pin);

Skip this helper variable.

> + state = state != 0 ? out_en : 0;

Uh that is really hard to read and modified a parameter. Skip that too.

> + bootpin_val = (state << (8U)) | out_en;

What you want is mask and set.

bootpin_val = BIT(pin + 8);

> + /* Configure bootpin value */
> + ret = zynqmp_pm_bootmode_write(bootpin_val);

This just looks weird.

Why are you not reading the value first since you are using read/modify/write?

I *think* you want to do this:

ret = zynqmp_pm_bootmode_read(&val);
if (ret)
/* error handling */
if (state)
val |= BIT(pin + 8);
else
val &= ~BIT(pin + 8);
ret = zynqmp_pm_bootmode_write(val);
if (ret)
/* error handling */

> +/*
> + * modepin_gpio_dir_in - Set the direction of the specified GPIO pin as input
> + * @chip: gpio_chip instance to be worked on
> + * @pin: gpio pin number within the device
> + *
> + * Return: 0 always
> + */
> +static int modepin_gpio_dir_in(struct gpio_chip *chip, unsigned int
> +pin) {
> + return 0;
> +}

I think you said this was configurable in the commit message.

Use the define GPIO_LINE_DIRECTION_OUT rather than 0.

> +static int modepin_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
> + int state) {
> + return 0;
> +}

Configurable?

> + status = devm_gpiochip_add_data(&pdev->dev, chip, chip);
> + if (status)
> + dev_err_probe(&pdev->dev, status,
> + "Failed to add GPIO chip\n");

just return dev_err_probe(...)

Yours,
Linus Walleij